High‐density polyethylene reinforced with submicron titania particles

Submicron titania particles were prepared by means of two different synthetic procedures in order to obtain different particle size (diameter ranging from 20 to 350 nm), shapes, and morphologies (amorphous or crystalline). Titania particles were surface modified with octadecylsilane in order to improve their compatibility with respect to polymeric matrices. High‐density polyethylene (HDPE)–titania composites were prepared by melt blending by using an internal mixer. The obtained composites were mechanically characterized in quasi static and creep tensile conditions. The presence of submicron titania particles (1 %vol) led to a significant increase of elastic modulus (20–25%) with respect to the unreinforced HDPE together with a slight increase of yield stress and a decrease of ultimate elongation. An interesting reduction for both elastic and viscoelastic creep compliance components was also evidenced. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Tribological Behavior of Aluminum Alloy AlSi10Mg-TiB<Subscript>2</Subscript> Composites Produced by Direct Metal Laser Sintering (DMLS)

Direct metal laser sintering (DMLS) is an additive manufacturing technique for the production of parts with complex geometry and it is especially appropriate for structural applications in aircraft and automotive industries. Aluminum-based metal matrix composites (MMCs) are promising materials for these applications because they are lightweight, ductile, and have a good strength-to-weight ratio This paper presents an investigation of microstructure, hardness, and tribological properties of AlSi10Mg alloy and AlSi10Mg alloy/TiB₂ composites prepared by DMLS. MMCs were realized with two different compositions: 10% wt. of microsize TiB₂, 1% wt. of nanosize TiB₂. Wear tests were performed using a pin-on-disk apparatus on the prepared samples. Performances of AlSi10Mg samples manufactured by DMLS were also compared with the results obtained on AlSi10Mg alloy samples made by casting. It was found that the composites displayed a lower coefficient of friction (COF), but in the case of microsize TiB₂ reinforcement the wear rate was higher than with nanosize reinforcements and aluminum alloy without reinforcement. AlSi10Mg obtained by DMLS showed a higher COF than AlSi10Mg obtained by casting, but the wear rate was higher in the latter case.     

Regulatory Noncoding and Predicted Pathogenic Coding Variants of CCR5 Predispose to Severe COVID-19

Genome-wide association studies (GWAS) found locus 3p21.31 associated with severe COVID-19. CCR5 resides at the same locus and, given its known biological role in other infection diseases, we investigated if common noncoding and rare coding variants, affecting CCR5, can predispose to severe COVID-19. We combined single nucleotide polymorphisms (SNPs) that met the suggestive significance level (P ≤ 1 × 10⁻⁵) at the 3p21.31 locus in public GWAS datasets (6406 COVID-19 hospitalized patients and 902,088 controls) with gene expression data from 208 lung tissues, Hi-C, and Chip-seq data. Through whole exome sequencing (WES), we explored rare coding variants in 147 severe COVID-19 patients. We identified three SNPs (rs9845542, rs12639314, and rs35951367) associated with severe COVID-19 whose risk alleles correlated with low CCR5 expression in lung tissues. The rs35951367 resided in a CTFC binding site that interacts with CCR5 gene in lung tissues and was confirmed to be associated with severe COVID-19 in two independent datasets. We also identified a rare coding variant (rs34418657) associated with the risk of developing severe COVID-19. Our results suggest a biological role of CCR5 in the progression of COVID-19 as common and rare genetic variants can increase the risk of developing severe COVID-19 by affecting the functions of CCR5.     

Long-Term Efficacy of Intranasal Esketamine in Treatment-Resistant Major Depression: A Systematic Review

Esketamine (ESK) has been approved as a rapid-acting intranasal treatment for treatment-resistant depression (TRD). Although existing studies have investigated the efficacy of ESK in the 4-week induction phase, our knowledge about long-term ESK efficacy remains poor. The aim of this systematic review was to summarize the available data on long-term ESK efficacy for TRD. A systematic search was performed including articles in English, up to 31 March 2021. The search found 7 relevant studies, involving 1024 adult TRD patients. Continuing treatment with ESK after the 4-week induction phase may be associated with stable efficacy in relapse prevention among TRD patients. Conversely, the long-term antidepressant effectiveness upon discontinuation of ESK might be limited, although data from three studies had a moderate to high risk of bias. Overall, the results on the effectiveness of this compound in the long term are mixed. According to our findings, ESK treatment should be continued following the induction phase to reach a stable efficacy in relapse prevention, while the long-term antidepressant and anti-suicidal effects of ESK after discontinuation are inconsistent. Currently, the level of proof of ESK efficacy in long-term TRD treatment remains low and more RCTs with larger sample sizes and active comparators are needed.     

Optimization of the working cycle for a hydrogen production and power generation plant based on aluminum combustion with water

The working cycle of a novel hydrogen and power generation system based on aluminum combustion with water is analyzed in order to evaluate the best performance in terms of energy conversion efficiency. The system exploits the exothermic reaction between aluminum and steam and produces thermal power for a super-heated steam cycle and hydrogen as a by-product of the reaction.     

Experimental study of dry reforming of biogas in a tubular anode-supported solid oxide fuel cell

The performance of a tubular Ni/YSZ anode supported SOFC directly fed by an anaerobic digestion simulated biogas, with an extra addition of carbon dioxide to operate in conservative operating conditions to avoid coking on the anode support, was investigated. The fuel cell has been tested at a fixed oven temperature of 800 °C and under biogas/CO₂ mixtures with different volumetric ratios, fuel utilization (FU) and current densities. Polarization curves and performance maps were obtained to better understand the influence of the investigated operational parameters on the cell behavior. Furthermore, since the tubular geometry enables an easy separation of the anode and cathode exhaust gases, the anode off-gas has been collected and monitored through a gas-chromatograph under open circuit voltage to investigate on the catalytic behavior of a Ni-based state-of-the-art anode. For corresponding operative conditions, performances of the cell for biogas/CO₂ 1/1.5 (i.e. CH₄/CO₂ 30/70) and 1/2 (i.e. CH₄/CO₂ 24/76) were at least 2% and 4% lower than the case 1/1 (i.e. CH₄/CO₂ 20/80), respectively. The highest efficiency of 43.4% was reached at 17.5 A and FU = 70%.     

Combustion of fine aluminum and magnesium powders in water

Micron-sized metal powders carried by a nitrogen flow were fed along the axis of a cylindrical hydrogen/oxygen diffusion flame. The particles ignited and burned in the water vapor at approximately 2500 K. Experiments were performed at atmospheric pressure. The environment in which particles burned was characterized in detail using computational fluid dynamics. The computations confirmed that the metal powders burned in water while the effect of oxygen and other oxidizing species could be neglected. Combustion was characterized experimentally for micron-sized powders of both aluminum and magnesium. Particle size distributions were measured using low-angle laser light scattering. Optical emission of the burning particles was recorded using filtered photomultiplier tubes. Measured durations of individual particle emission pulses were assumed to represent their burn times; these data were classified into logarithmically spaced time bins. The distribution of the particle burn times was correlated with their size distributions assuming that larger size particles burned longer. It was observed that correlation between the burn times, t, and particle diameters, D, can be approximately described as t ∼ D^0.64 and t ∼ D^0.68 for aluminum and magnesium powders, respectively. The results were compared to previous reports and possible reasons for discrepancies between the present and earlier results were discussed.