PbS和PbO反应动力学及其机理SCIEI

本文得出了PbS和PbO交互反应的速率方程:(da)/(dt)=kx_(PbS)~3x_(PbO)^(-2);发现了反应过程中有过渡产物碱式硫酸铅(PbSO_4·2PbO);从电子转移角度,探讨了反应机理。     

Ti3SiC2在900℃与1000℃下的热腐蚀行为

研究了Ti3SiC2三元层状陶瓷材料在900和1000℃下由Na2SO4盐膜引起的热腐蚀行为，用XRD及SEM分析了腐蚀产物膜的成分、结构和形貌等。实验表明，腐蚀膜由TiO2和SiO2混合组成：在结构上明显地分成两层，外层晶粒粗大且多孔，内层晶粒细小且致密。Ti3SiC2与熔融盐接触时遭受较严重的腐蚀。     

Microstructure and Application of YBCO Superconductive Films with Low Surface Resistance

ＭｉｃｒｏｓｔｒｕｃｔｕｒｅａｎｄＡｐｐｌｉｃａｔｉｏｎｏｆＹＢＣＯＳｕｐｅｒｃｏｎｄｕｃｔｉｖｅＦｉｌｍｓｗｉｔｈＬｏｗＳｕｒｆａｃｅＲｅｓｉｓｔａｎｃｅＷａｎｇＸｉａｏｐｉｎｇ，ＹａｎｇＢｉｎｇｃｈｕａｎ，ＳｈｉＤｏｎｇｑｉ，ＰｅｎｇＺｈｅｎｇ...     

淬火态TC4合金热循环硬化行为及断口特征

在７７－６２３Ｋ对淬火态ＴＣ４合金进行了热循环试验，测定了合金热循环后的硬度，并与６２３Ｋ时效合金的硬度进行了对比；还观察了拉伸试样断口形貌。结果表明：热应力能加速亚稳相的分解，使合金中的位错密度升高，层错和形变孪晶的数量增多；循环温度场作用下淬火态合金拉伸试样断口由韧窝型断裂向韧窝和撕裂棱混合型断裂转变。     

FRACTURE BEHAVIOUR AND FRACTURE TOUGHNESS OF Al-2.5Li-1.3Cu-0.9Mg-0.13Zr ALLOY

The fracture mechanism for Al-2.5Li-1.3Cu-0.9Mg-0.13Zr alloy is quite different fromundergone various regimes of heat treatment.With the decrease of solution temperature andthe increase of aging temperature,the intergranular delamination and necking fracture on thefracture surface increase and the shearing facture decreases.Thus,the toughness of the alloymay be much improved.     

MOCVD Growth of Doped GaAs/AlGaAs Quantum Heterostructures

The influences of growth techniques of AP-MOCVD GaAs/AlGaAs silicon-doped multi-quantum wells(MQWs), heterostructure bipolar transistors (HBTs), double barrier resonant tunneling diodes(DBRTDs) ontheir structures and performances were studied. Continuously grown MQWs, that is, no growth interruption atthe heterointerfaces, shown blue-shifted, narrower and stronger photoluminescence(PL) compared withinterruptedly grown ones.TEM examination of the interrupted interfaces revealed a bright line correspondingto the compositional fluctuation and impurity adsorption, and indicated noncommutative structures ofAlGaAs/GaAs and GaAs/AlGaAs interfaces. High performance HBTs and DBRTDs were obtained bycontinuously grown method while growth interruption caused performance degradation. It was concluded thatgrowth interruption may cause accumulation of residua1 impurities in the ambient as well as compositionalfluctuation while continuous growth at very low growth rates can overcome such problems.     

Resistance welding of carbon fibre reinforced polyetheretherketone composites using metal mesh and PEI film

Weldability of polyetheretherketone( PEEK) with polyetherimide( PEI) is tested. And carbon fiber reinforced PEEK laminates are resistance welded using stainless steel mesh heating element. The effects of the welding time and welding pressure on the lap shear strength of joints are investigated. Results show that PEEK can heal with PEI well in welding condition and the lap shear strength of PEEK/CF(carbon fibre) joint increases linearly with welding time, but reaches a maximum value when welding pressure ranging from 0.3 MPa to 0.5 MPa with constant welding time. The fracture characteristics of surface are analyzed by SEM techniques, and four types of fracture modes of lap shear joints are suggested.     

流动液体中夹杂物超声去除的影响因素

以高密度聚乙烯（HDPE）颗粒和水形成的悬浮液为研究体系。考察了有无超声波作用下。介质流量、夹杂物数量以及夹杂物的粒径对总去除率、上浮去除率、壁面粘附去除率的影响。实验结果表明，在短时间内（30s)超声波对流动液体中的夹杂物具有明显的去除效果。总去除率达93％。夹杂物的总去除率随着超声波输入电功率的增大而提高；超声波对较多数量或较大粒径的夹杂物去除效果更显著。超声波作用下流动液体中的夹杂物比静止液体中的更容易去除。超声波对流动液体中夹杂物去除效果的去除机理主要是通过气泡捕获夹杂物，超声空化效应产生直接包裹夹杂物的气泡以及通过夹杂物碰撞凝聚使夹杂物容易上浮实现去除。     

Au-Ni-Kovar合金系统基底元素表面偏聚的SAM和XPS研究SCIEI

本文采用SAM和XPS对实用Au-Ni-Kovar合金系统热处理样品(250—350℃,0.5—1.5h)进行了基底元素穿透Au层的表面偏聚研究,给出了这一复杂系统中Ni,Co表面偏聚机理的直观证据,即Ni,Co主要是通过晶界扩散穿透Au层而后以表面扩散覆盖镀Au表面的;表面偏聚元素化学态的研究则不仅表明,氧的吸附和氧化反应是Ni,Co表面偏聚的驱动力,而且发现,上述偏聚会引起样品表面吸水的现象。     

Ti-6Al-4V合金在真空中的干滑动磨损行为

在真空(10^-^5Pa)条件下对Ti-6Al-4V合金进行了系统的磨损性能测试，研究了载荷和滑动速度对Ti-6Al-4V合金磨损率的影响．对Ti-6Al-4V合金的磨损表面进行了显微组织分析．实验结果表明，Ti-6Al-4V合金的磨损率随载荷和滑动速度的升高而增加．磨损表面具有层状结构的舌状形貌特征，分析表明这是Ti-6Al-4V合金表面通过接触点处材料的被推挤和碾压过程形成了特殊的变形堆砌层的结果．显微组织分析显示，这种变形堆砌层具有50—100nm尺寸的细小显微组织结构和50mm以上的厚度．