Thermomechanical properties of copper–carbon nanofibre composites prepared by spark plasma sintering and hot pressing

Several types of carbon nanofibres (CNF) were coated with a uniform and dense copper layer by electroless copper deposition. The coated fibres were then sintered by two different methods, spark plasma sintering (SPS) and hot pressing (HP). The Cu coating thickness was varied so that different volume fraction of fibres was achieved in the produced composites. In some cases, the CNF were pre-coated with Cr for the improvement the Cu adhesion on CNF. The results show that the dispersion of the CNF into the Cu matrix is independent of the sintering method used. On the contrary, the dispersion is directly related to the efficiency of the Cu coating, which is tightly connected to the CNF type. Overall, strong variations of the thermal conductivity (TC) of the composites were observed (20–200 W/mK) as a function of CNF type, CNF volume fraction and Cr content, while the coefficient of thermal expansion (CTE) in all cases was found to be considerably lower than Cu (9.9–11.3 ppm/K). The results show a good potential for SPS to be used to process this type of materials, since the SPS samples show better properties than HP samples even though they have a higher porosity, in applications where moderate TC and low CTE are required.     

Influence of Molecular Weight on the Performance of Organic Solar Cells Based on a Fluorene Derivative

The performance of organic photovoltaic (OPV) bulk‐heterojunction blends comprising a liquid‐crystalline fluorene derivative and a small‐molecular fullerene is found to increase asymptotically with the degree of polymerization of the former. Similar to various thermodynamic transition temperatures as well as the light absorbance of the fluorene moiety, the photocurrent extracted from OPV devices is found to strongly vary with increasing oligomer size up to a number average molecular weight, M_n ≈ 10 kg mol^?1, but is rendered less chain‐length dependent for higher M_n as the fluorene derivative gradually adopts polymeric behavior.     

Effect of titanium–magnesium catalyst morphology on the properties of polypropylene upon propylene polymerization in a liquid monomer

The effect of the particle size of an IK-8-21 domestic titanium-magnesium catalyst on the properties of polypropylene (PP) produced during the polymerization of propylene in a liquid monomer is studied. Catalysts with particle sizes of 20 to 64 μm are shown to have high activity and identical sensitivity to hydrogen and allow PP to be obtained with a narrow distribution of particles over size, high isotacticity, and close values of crystallinity, melting temperature, and physicomechanical properties. A slight decrease in the activity and bulk density of PP powder is observed when the average size of catalyst particles is increased from 20 to 43 μm. A more notable reduction in the activity and bulk density of PP powder is observed for catalyst with particle sizes of 62 to 64 μm. IK-8-21 catalyst is not inferior to its foreign analogues with respect to the properties of the resulting PP.     

Orange to green switching anthraquinone-based electrochromic material

An easily accessible anthraquinone-benzodithiophene-based high bandgap polymer (PTAq) was synthesized by Stille coupling reactions in remarkably high yield (96.5%). The highest occupied molecular orbital energy level of the polymer was estimated from the onset of oxidation in a cyclic voltammetry study to be −5.7 eV. PTAq showed an orange-to-green color switching with the application of a 1.0-V external potential to the polymer film, which was visible to the naked eye. The optical behavior change was also monitored using ultraviolet–visible absorption spectroscopy and revealed a respectable 75% transmittance change when the polymer film was subjected to a 1.0-V external potential. The high color contrast observed makes PTAq one of the most promising materials for electrochromic device applications. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47729.     

Biosynthesis of Jasmonates from Linoleic Acid by the Fungus Fusarium oxysporum. Evidence for a Novel Allene Oxide Cyclase

Fusarium oxysporum f. sp. tulipae (FOT) secretes (+)-7-iso-jasmonoyl-(S)-isoleucine ((+)-JA-Ile) to the growth medium together with about 10 times less 9,10-dihydro-(+)-7-iso-JA-Ile. Plants and fungi form (+)-JA-Ile from 18:3n-3 via 12-oxophytodienoic acid (12-OPDA), which is formed sequentially by 13S-lipoxygenase, allene oxide synthase (AOS), and allene oxide cyclase (AOC). Plant AOC does not accept linoleic acid (18:2n-6)-derived allene oxides and dihydrojasmonates are not commonly found in plants. This raises the question whether 18:2n-6 serves as the precursor of 9,10-dihydro-JA-Ile in Fusarium, or whether the latter arises by a putative reductase activity operating on the n-3 double bond of (+)-JA-Ile or one of its precursors. Incubation of pentadeuterated (d₅) 18:3n-3 with mycelia led to the formation of d₅-(+)-JA-Ile whereas d₅-9,10-dihydro-JA-Ile was not detectable. In contrast, d₅-9,10-dihydro-(+)-JA-Ile was produced following incubation of [17,17,18,18,18-²H₅]linoleic acid (d₅-18:2n-6). Furthermore, 9(S),13(S)-12-oxophytoenoic acid, the 15,16-dihydro analog of 12-OPDA, was formed upon incubation of unlabeled or d₅-18:2n-6. Appearance of the α-ketol, 12-oxo-13-hydroxy-9-octadecenoic acid following incubation of unlabeled or [¹³C₁₈]-labeled 13(S)-hydroperoxy-9(Z),11(E)-octadecadienoic acid confirmed the involvement of AOS and the biosynthesis of the allene oxide 12,13(S)-epoxy-9,11-octadecadienoic acid. The lack of conversion of this allene oxide by AOC in higher plants necessitates the conclusion that the fungal AOC is distinct from the corresponding plant enzyme.     

Effects of thiol additives on urethane acrylate UV primers for SMC applications

Sheet molded compound (SMC) is a highly filled, glass fiber reinforced, thermoset material used in trim and body panel automotive parts. When SMC-substrates are coated with conventional thermally cured paints, inherent porosity and entrapped volatiles of the substrate result in popping (“paint pops”) defects. UV-curable primers (UVP) provide an order of magnitude reduction of paint defects in SMC coatings, but typically have poor adhesion. Mercaptan polymers have a long history, dating back to 1928, of use in adhesives and sealant applications. The present study investigates a series of UVPs, showing the effect of resin functionality and thiol functional additive content on the adhesion of the coatings to SMC substrates. The SMC formulation is also considered when evaluating UVP adhesion, regarding variables such as surface chemistry, morphology, and surface area. The present study brings to light how adhesion of acrylate UVP can be enhanced with mercaptan moieties in additive amounts. The effect is most apparent on SMC substrates that have been treated to expose inorganic fillers as opposed to untreated surfaces of polyester. Additionally annealing the films boosts adhesion, but only in thiol containing formulations. This is a result of the decrease in T_gs and modulus of the films with the addition of mercaptans, thus providing better contact with the substrate in comparison to non-thiol containing formulations.     

Eccentric Circumferential Cracks in Cylindrical Specimens

The effect of eccentricity on the stress intensity factors for circumferential cracks in cylindrical specimens subjected to torsional and axial loading is studied. BEM solutions are compared with proposed approximate methods and some agreement is found for the axial load cases. A simple method of how the eccentricity develops under axial loading as the crack grows is presented. It shows that the eccentricity accelerates as the crack grows and that the problem thereby can be characterized as unstable.