1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Training and optimization of an artificial neural network controlling a hybrid power filter

A hybrid power compensator (HPC) consisting of a static VAr compensator and a dynamic compensator needs to be optimally controlled during the compensation of nonlinear loads. The HPC must be controlled to meet minimum requirements in terms of power factor and harmonic distortion, while at the same time minimizing its total cost. An artificial neural network (ANN) is used to control the HPC amidst a very dynamic power system environment. The performance of a reference ANN is evaluated while controlling an HPC connected to a typical nonlinear industrial load. The training and performance of the ANN is then optimized in terms of training set size, training set packing and ANN topology and the performance compared to the reference ANN. This paper highlights the importance of optimising the mentioned ANN parameters to achieve optimum ANN training and modeling accuracy. The results obtained reveals that the application of an ANN in controlling an HPC is feasible given that the ANN parameters are chosen appropriately.     

Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.     

The First Template‐Free Growth of Crystalline Silicon Microtubes

A simple template‐free high‐temperature evaporation method was developed for the growth of crystalline Si microtubes for the first time. As‐grown Si microtubes were characterized using X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, and room‐temperature photoluminescence. The lengths of the Si tubes can reach several hundreds of micrometers; some of them have lengths on the order of millimeters. Each tube has a uniform outer diameter along its entire length, and the typical outer diameter is ≈ 2–3 μm. Most of the tubes have a wall thickness of ≈ 400–500 nm, though a considerable number of them exhibit a very thin wall thickness of ≈ 50 nm. Room‐temperature photoluminescence measurement shows the as‐synthesized Si microtubes have two strong emission peaks centered at ≈ 589 nm and ≈ 617 nm and a weak emission peak centered at ≈ 455 nm. A possible mechanism for the formation of these Si tubes is proposed. We believe that the present discovery of the crystalline Si microtubes will promote further experimental studies on their physical properties and smart applications.     

Influence of device engineering on the analog and RF performances of SOI MOSFETs

This work presents a systematic comparative study of the influence of various process options on the analog and RF properties of fully depleted (FD) silicon-on-insulator (SOI), partially depleted (PD) SOI, and bulk MOSFET's with gate lengths down to 0.08 /spl mu/m. We introduce the transconductance-over-drain current ratio and Early voltage as key figures of merits for the analog MOS performance and the gain and the transition and maximum frequencies for RF performances and link them to device engineering. Specifically, we investigate the effects of HALO implantation in FD, PD, and bulk devices, of film thickness in FD, of substrate doping in SOI, and of nonstandard channel engineering (i.e., asymmetric Graded-channel MOSFETs and gate-body contacted DTMOS).     

An improved statistical analysis of the least mean fourth (LMF) adaptive algorithm

The paper presents an improved statistical analysis of the least mean fourth (LMF) adaptive algorithm behavior for a stationary Gaussian input. The analysis improves previous results in that higher order moments of the weight error vector are not neglected and that it is not restricted to a specific noise distribution. The analysis is based on the independence theory and assumes reasonably slow learning and a large number of adaptive filter coefficients. A new analytical model is derived, which is able to predict the algorithm behavior accurately, both during transient and in steady-state, for small step sizes and long impulse responses. The new model is valid for any zero-mean symmetric noise density function and for any signal-to-noise ratio (SNR). Computer simulations illustrate the accuracy of the new model in predicting the algorithm behavior in several different situations.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

用于单芯片系统的改进型WXGA LCoS成像器

本文讨论用于单芯片时序混色的菲利浦DD-720硅基液晶(LCoS)片。这种芯片主要用于HDTV背投影机和多媒体系统。与菲利浦以前的单片LCoS设计相比，由于该芯片具有电接口接点较少、封装简单和温度传感器内置等许多特点，使其应用于投影系统时成本降低。