Effect of surface roughness and surface modification of indium tin oxide electrode on its potential response to tryptophan

The effect of surface modification of indium tin oxide (ITO) electrode on its potential response to tryptophan was investigated for ITO substrates with different surface roughness. It was found that a small difference in surface roughness, between ∼1 and ∼2 nm of R_a evaluated by atomic force microscopy, affects the rest potential of ITO electrode in the electrolyte. A slight difference in In:Sn ratio at the near surface of the ITO substrates, measured by angle-resolved X-ray photoelectron spectrometry and Auger electron spectroscopy is remarkable, and considered to relate with surface roughness. Interestingly, successive modification of the ITO surface with aminopropylsilane and disuccinimidyl suberate, of which essentiality to the potential response to indole compounds we previously reported, improved the stability of the rest potential and enabled the electrodes to respond to tryptophan in case of specimens with R_a values ranging between ∼2 and ∼3 nm but not for those with R_a of ∼1 nm. It was suggested that there are optimum values of effective work function of ITO for specific potential response to tryptophan, which can be obtained by the successive modification of ITO surface.     

Flammability behavior of fiber–fiber hybrid fabrics and composites

The effect of heat flux levels on burning behavior and heat transmission properties of hybrid fabrics and composites has been investigated using cone calorimeter and heat transmission techniques. The hybrid fabric structures woven out of E‐glass (warp) and polyether ether ketone (PEEK) (weft) and E‐glass (warp) and polyester (weft) have been studied at high heat flux levels keeping in view the flame retardant requirements of structural composites. The performance of the glass–PEEK fabric even at high heat flux levels of 75 kW/m² was comparable with the performance of glass–polyester fabric evaluated at 50 kW/m². The results further demonstrate that glass–PEEK hybrid fabrics exhibit low peak heat release rate, low heat release rate, low heat of combustion, suggesting an excellent combination of materials and fall under the low‐risk category and are comparable with the performance of carbon fiber‐epoxy‐based systems. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Compressive mechanical properties of sawdust/high density polyethylene composites under various strain rate loadings

This article is concerned with the static and dynamic mechanical properties of high‐density polyethylene (HDPE) reinforced with sawdust (SD) at a strain rate of up to 10³ s^?1. In this study, the static and dynamic properties of HDPE/SD composites with different filler loadings of 5, 10, 15, 20, and 30 wt% SD were deliberated at different levels of strain rates (0.001, 0.01, 0.1, 650, 900, and 1100 s^?1) using a conventional universal testing machine and the split Hopkinson pressure bar apparatus. The results showed that the stress–strain curves, yield behavior, stiffness, and strength properties of the HDPE/SD composites were strongly affected by both the strain rate and the filler loadings. Furthermore, the rate sensitivityof the HDPE/SD composites showed a great dependency on the applied strain rate, increasing as the strain rate increased. However, the thermal activation values showed a contrary trend. Meanwhile, for the postdamage analysis, the results showed that the applied strain rates influenced the deformation behavior of the tested HDPE/SD composites. Moreover, for the fractographic analysis at dynamic loading, the composites showed that all the specimens underwent a severe catastrophic deformation. J. VINYL ADDIT. TECHNOL., 24:162–173, 2018. © 2016 Society of Plastics Engineers     

Synthesis of poly(acrylonitrile‐co‐divinylbenzene‐co‐vinylbenzyl chloride)‐derived hypercrosslinked polymer microspheres and a preliminary evaluation of their potential for the solid‐phase capture of pharmaceuticals

Poly[acrylonitrile (AN)‐co‐divinylbenzene (DVB)‐co‐vinylbenzyl chloride (VBC)] terpolymers were synthesized by precipitation polymerization in the form of porous polymer microspheres. The poly(AN‐co‐DVB‐co‐VBC) polymers were then hypercrosslinked, via a Friedel‐Crafts reaction with FeCl₃ in nitrobenzene, to provide a significant uplift in the specific surface areas of the polymers. FTIR spectra of the hypercrosslinked poly(AN‐co‐DVB‐co‐VBC)s showed that the chloromethyl groups derived from VBC were consumed by the Friedel‐Crafts reactions, which was consistent with successful hypercrosslinking. Hypercrosslinking installed a number of new, small pores into the polymers, as evidenced by a dramatic increase in the specific surface areas upon hypercrosslinking (from ～530 to 1080 m² g^?1). The hypercrosslinked polymers are very interesting for a range of applications, not least of all for solid‐phase extraction (SPE) work, where the convenient physical form of the polymers (beaded format), their low mean particle diameters, and narrow particle size distributions, as well as their high specific surface areas and polar character (arising from the AN residues), make them attractive candidates as SPE sorbents. In this regard, in a preliminary study one of the hypercrosslinked polymers was utilized as an SPE sorbent for the capture of the polar pharmaceutical diclofenac from a polar environment. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45677.     

Melt compounded nanocomposites with semi‐interpenetrated network structure based on natural rubber,polyethylene, and carrot nanofibers

The present study deals with the processing and characterization of cellulose nanocomposites natural rubber (NR), low‐density polyethylene (LDPE) reinforced with carrot nanofibers (CNF) with the semi‐interpenetrated network (S‐IPN) structure. The nanocomposites were compounded using a co‐rotating twin‐screw extruder where a master‐batch of NR and CNF was fed to the LDPE melt, and the NR phase was crosslinked with dicumyl peroxide. The prepared S‐IPN nanocomposites exhibited a significant improvement in tensile modulus and yield strength with 5 wt % CNF content. These improvements are due to a better phase dispersion in the S‐IPN nanocomposites compared with the normal blend materials, as demonstrated by optical microscopy, electron microscopy and ultraviolet–visible spectroscopy. The S‐IPN nanocomposite also displayed an improved crystallinity and higher thermal resistance compared with NR, CNF, and the normal blend materials. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45961.     

Synthesis of poly(ε‐caprolactone)/clay nanocomposites using polyhedral oligomeric silsesquioxane surfactants as organic modifier and initiator

Poly(ε‐caprolactone)/clay nanocomposites were synthesized by in situ ring‐opening polymerization of ε‐caprolactone in the presence of montmorillonite modified by hydroxyl functionalized, quaternized polyhedral oligomeric silsesquioxane (POSS) surfactants. The octa(3‐chloropropyl) polyhedral oligomeric silsesquioxane was prepared by hydrolytic condensation of 3‐chloropropyltrimethoxysilane, which was subsequently quaternized with 2‐dimethylaminoethanol. Montmorillonite was modified with the quaternized surfactants by cation exchange reaction. Bulk polymerization of ε‐caprolactone was conducted at 110°C using stannous octoate as an initiator/catalyst. Nanocomposites were analyzed by X‐ray diffraction, transmission electron microscopy, thermo gravimetric analysis, and differential scanning calorimetry. Hydroxyl functionalized POSS was employed as a surface modifier for clay which gives stable clay separation for its 3‐D structure and also facilitates the miscibility of polymer with clay in the nanocomposites due to the star architecture. An improvement in the thermal stability of PCL was observed even at 1 wt % of clay loading. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Flexible and Conductive 3D Printable Polyvinylidene Fluoride and Poly(N,N‐dimethylacrylamide) Based Gel Polymer Electrolytes

In this work, 3D printable gel polymer electrolytes (GPEs) based on N,N‐dimethylacrylamide (DMAAm) and polyvinylidene fluoride (PVDF) in lithium chloride containing ethylene glycol solution are synthesized and their physicochemical properties are investigated. 3D printing is carried out with a customized stereolithography type 3D gel printer named “Soft and Wet Intelligent Matter‐Easy Realizer” and free forming GPE samples having variable shapes and sizes are obtained. Printed PVDF/PDMAAm‐based GPEs exhibit tunable mechanical properties and favorable thermal stability. Electrochemical proprieties of the printed GPEs are carried out via impedance spectroscopy in the temperature range of 25–90 °C by varying PVDF content. Ionic conductivity as high as 6.5 × 10^?4 S cm^?1 is achieved at room temperature for GPE containing low PVDF content (5 wt%) and conductivity of the GPEs is increased as temperature rises.     

Study of morphology and gas separation properties of polysulfone/titanium dioxide mixed matrix membranes

Polysulfone (PSf)‐based mixed matrix membranes (MMMs) with the incorporation of titanium dioxide (TiO₂) nanoparticles were prepared. Distribution and agglomeration of TiO₂ in polymer matrix and also surface of membranes were observed by scanning electron microscopy, transmission electron microscopy, and energy dispersive X‐ray. Variation in surface roughness of MMMs with different TiO₂ loadings was analyzed by atomic force microscopy. Physical properties of membranes before and after cross‐linking were identified through thermal gravimetric analysis. At low TiO₂ loadings (≤3 wt%), both CO₂ and CH₄ permeabilities decreased and consequently gas selectivity improved and reached to 36.5 at 3 bar pressure. Interestingly, PSf/TiO₂ 3 wt% membrane did not allow to CH₄ molecules to pass through the membrane and this sample just had CO₂ permeability at 1 bar pressure. Gas permeability increased considerably at high filler contents (≥5 wt%) and CO₂ permeance reached to 37.7 GPU for PSf/TiO₂ 7 wt% at 7 bar pressure. It was detected that, critical nanoparticle aggregation has occurred at higher filler loadings (≥5 wt%), which contributed to formation of macrovoids and defects in MMMs. Accordingly, MMMs with higher gas permeance and lower gas selectivity were prepared in higher TiO₂ contents (≥5 wt%). POLYM. ENG. SCI., 55:367–374, 2015. © 2014 Society of Plastics Engineers     

Influence of Some Hofmeister Anions on the Krafft Temperature and Micelle Formation of Cetylpyridinium Bromide in Aqueous Solution

In this work, the effect of some Hofmeister anions on the Krafft temperature (T_K) and micelle formation of cetylpyridinium bromide (CPB) have been studied. The results show that more chaotropic anions increase, while the less chaotropic ones lower the T_K of the surfactant. More chaotropic I^? and SCN^? form contact ion pairs with the cetylpyridinium ion and reduce the electrostatic repulsion between the CPB molecules. As a result, these ions show salting‐out behavior, with a consequent increase in the T_K. In contrast, less chaotropic Cl^? and NO₃^? increase the activity of free water molecules and enhance hydration of CPB molecules, showing a decrease in the T_K. A rather unusual behavior was observed in the case of SO₄^2? and F^?. These strong kosmotropes shift from their usual position in the Hofmeister series and behave like moderate chaotropes, lowering the T_K of the surfactant. Because of the high charge density and the strong tendency for hydration these ions preferentially remain in the bulk. Rather than forming contact ion pairs, these ions stay away from the CPB molecules, decreasing the T_K of the surfactant. In term of decreasing the T_K, the ions follow the order NO₃^? > SO₄^2? > Cl^? > F^? > Br^? > SCN^? > I^?. The critical micelle concentration (CMC) of the surfactant decreases significantly in the presence of these ions due to the screening of the micelle surface charge by the excess counterions. The decreasing trend of the CMC in the presence of the salts follows the order SCN^? > I^? > SO₄^2? > NO₃^? > Br^? > Cl^? > F^?.     

Electrochemical Impedance Spectroscopic Analysis of Sensitization-Based Solar Cells

Electrochemical impedance spectroscopy (EIS) is a very powerful tool for elucidation of charge transfer and transport processes in sensitization-based solar cells (e.g., dye-sensitized solar cells [DSSCs], quantum dot-sensitized solar cells [QDSSCs], and perovskite solar cells [PSCs]). EIS measures the electrochemical response to small amplitude AC signals over a wide range of frequencies. Analysis of the EIS response provides information about the corresponding parameters of the cells. Here, we review the fundamentals of EIS, charge transport kinetic processes, and equivalent circuit models of sensitization-based solar cells and use these concepts to explain the EIS spectra of DSSCs, QDSSCs, and PSCs. This review will be very useful for understanding the fundamental charge transfer and transport processes in different sensitization-based solar cells and the use of an equivalent circuit model to interpret the observed charge transfer and reactions.