柴油机自动减压起动装置的有限元分析

分析了柴油机自动减压装置的工作原理,针对在潍柴WP10型柴油机上加装的减压装置,利用Solidworks Simulation对压板进行了静力分析,找出了应力最大的部位和最大值,并按照Von Mises准则,判别压板满足刚度要求。     

Optimization of uncertain acoustic metamaterial with Helmholtz resonators based on interval model

Uncertainties existing in the acoustic metamaterial may strongly affect its unusual properties. Aiming at this actuality, the interval model is introduced to treat with uncertainties existing in the acoustic metamaterial with Helmholtz resonators. Frequency intervals in which the sound intensity transmission coefficients are certainly less than the required value and the effective bulk moduli are certainly negative are defined as conservative approximations. Frequency intervals in which the sound intensity transmission coefficients may be less than the required value and the effective bulk moduli may be negative are defined as unsafe approximations. The proportion of the conservative approximation and the unsafe approximation is defined as an approximate precision. Based on the quantification of uncertainties of the sound intensity transmission coefficients and the negative effective bulk moduli, an optimization model for the interval acoustic metamaterial with Helmholtz resonators is constructed. Numerical results showed that even suffering from effects of interval parameters, unusual properties of the optimized acoustic metamaterial (such as the bandgap of the sound transmission and the negative effective bulk modulus) could be improved.     

Polybrominated Diphenyl Ethers in Surface Sediment from Songhua River Basin, Northeast of China

Sixty sediment samples were collected from the main Songhua River in three years. Twelve polybrominated diphenyl ether ( PBDE) congeners ( BDE17, 28, 47, 66, 99, 100, 153, 154, 138, 183, and BDE?209) w...     

德惠断陷下白垩统碎屑岩储层特征及控制因素分析

德惠断陷下白垩统登娄库组、营城组、沙河子组储层物性差,勘探风险大.利用岩心观察、铸体薄片鉴定、扫描电镜分析、黏土X线衍射分析等方法,分析储层基本特征、储层成岩作用和控制因素.结果表明:德惠断陷下白垩统碎屑岩储层成分成熟度和结构成熟度较低,储层孔隙类型主要有残余原生孔、次生孔和混合孔,储层物性和孔隙结构较差;压实作用是导致储层物性变差的主要原因,溶蚀作用改善储层物性;纵向上发育2个次生孔隙带,主要形成于中成岩期,次生孔隙带的形成与有机质生烃排酸和断裂有关.研究结果为德惠断陷下白垩统进一步油田勘探提供地质依据,对其他地区类似储层研究有一定借鉴意义.     

Evaluation research on applicability of rapid iodide migration test

The applicability of the rapid iodide migration test was systematically studied. Comparative experimental tests of different test conditions, including several external voltages, test durations, concrete ages and mixing proportions, were carried out to make clear the transport behaviors of iodide under parallel electric fields. Numerical simulations were also done using the finite element method to found the correlation between chloride and iodide transport behaviors. The test and numerical results show that the chloride transport behaviors of RIM and RCM tests have a good correlation under the several conditions used in the present paper. Moreover, the influence of external conditions （external voltages, test durations） on the test results is small. Thus, it can be concluded that the RIM method is available to determine the chloride penetration resistance of the chloride-eroded structural concrete.     

Electrochemical investigation of La0.4Sr0.6TiO3 synthesized in air for SOFC application

Journal of Applied Electrochemistry - La-doped titanate materials have been widely investigated as alternative Ni-free anodes for solid oxide fuel cells (SOFCs). In this study, La0.4Sr0.6TiO3 (LST)...     

Size and pressure effects on solid transition temperatures of ZrO2

Transition temperatures between tetragonal and monoclinic polymorphs of ZrO₂ nanoparticles, thin films and nanostructured materials are calculated by considering energetic contributions of surface (interface) energy and surface stress on total Gibbs free energy. The transition temperatures drop as the size of the nanocrystals decreases, which is consistent with available results.     

耐候钢连铸工艺的改进

分析耐候钢连铸出现的问题,认为凝固时应力过大和磷铜元素偏析造成晶界脆化是出现铸坯纵裂的主要原因;结晶器中喂稀土丝恶化保护渣性能,影响结晶器与坯壳间的润滑与传热,并使热流不均匀是连铸漏钢的主因。采用钙处理代喂稀土丝工艺,以及减缓连铸一、二次冷却强度,改进保护渣后,连铸缺陷获得极大改善。     

保温条件下过共晶Al-Si合金半固态浆料的组织演变

研究了保温时间和保温温度对电磁搅拌ZL117合金半固态浆料稳定性的影响.试验结果表明：半固态浆料中初生Si的颗粒直径随着保温时间的延长而逐渐增大,但在前15 min内增长速度比较缓慢,15 min后增长较快;随着保温温度的升高而缓慢增大;初生Si的形状系数随着保温时间的延长而变得越来越大,但也在前15 min内变化较为缓慢,15 min后变大速度突然加快;初生Si的形状系数在620 ℃下保温时最小,在610～620 ℃之间随着保温温度的升高而缓慢变小;在620～650 ℃之间随着保温温度的升高而逐渐增加.     

TENSILE FRACURE IN AN Al-Li ALLOY 8090

ＴＥＮＳＩＬＥＦＲＡＣＵＲＥＩＮＡＮＡｌ－ＬｉＡＬＬＯＹ８０９０￥Ｊｉａｎｇ，Ｄａｍｉｎｇ；Ｗａｎｇ，Ｙｉｎｏｎｇ；Ｈｏｎｇ，Ｂａｎｄｅ；Ｌｅｉ，Ｔｉｎｇｑｕａｎ（ＨａｒｂｉｎＩｎｓｔｉｔｕｔｅｏｆＴｅｃｈｎｏｌｏｇｙ，Ｈａｒｂｉｎ１５００８０）Ｓｕ...