Effects of solid retention time on the performance of submerged anoxic/oxic membrane bioreactor.

In this study, four similar bench-scale submerged Anoxic/Oxic Membrane Bioreactors (MBR) were used simultaneously to investigate the effects of solids retention time (SRT) on organic and nitrogen removal in MBR for treating domestic wastewater. COD removal efficiencies in all reactors were consistently above 94% under steady state conditions. Complete conversion of NH(4+)-N to NO(3-)-N was readily achieved over a feed NH(4+)-N concentration range of 30 to 50 mg/L. It was also observed that SRT did not significantly affect the nitrification in the MBR systems investigated. The average denitrification efficiencies for the 3, 5, 10 and 20 days SRT operations were 43.9, 32.6, 47.5 and 66.5%, respectively. In general, the average effluent nitrogen concentrations, which were mainly nitrate, were about 22.2, 27.6, 21.7 and 13.9 mg/L for the 3, 5, 10 and 20 days SRT systems, respectively. The rate of membrane fouling at 3 days SRT operation was more rapid than that observed at 5 days SRT. No fouling was noted in the 10 days and 20 days SRT systems during the entire period of study.     

Thermal simulation for geometric optimization of metallizedpolypropylene film capacitors

In this paper, the authors use an analytical model to calculate the losses in the metallized polypropylene film capacitors. The model is validated experimentally for capacitors having the same capacitance but different geometry. For each group of capacitors, a temperature distribution in the roll is assumed with the aim of optimizing its thermal performance. It appears that the heating of a long capacitor is higher than that of an equivalent flat capacitor subjected to the same electric stresses     

A study on hydrogen storage by use of cryoadsorbents

This paper reports investigations on the techniques and economics of hydrogen storage by means of cryoadsorption. Also a comparison with alternative storage methods is included. The hydrogen storage capacity of several adsorbents in the temperature range 65–150 K has been investigated experimentally. Based on these data, economics and operating conditions for minimum total costs of the system are calculated. Utilization-factor and capacity-factor parameters are shown to be decisive for outlining the favourable ranges of application for competitive hydrogen storage methods.     

Novel bipolar differential input/output current-controlled current source

A new bipolar differential input/output current-controlled current source (CCCS) is described. The basic cell consists of a translinear array of six transistors with two bipolar inputs, and is suited for the input stage of a differential current-mode operational amplifier.     

Dicyanate semi IPNs—A new class of high performance,high temperature plastics

Dicyanate Semi-Interpenetrating Polymer Networks (semi IPNs) are made by dissolving a thermoplastic in crosslinking dicyanates and then curing the resulting mixture. The semi IPNs produced are strong, with tensile strengths of 10,000 to 12,000 psi, and flexible, with elongations to break of 10 to 17 percent. Dicyanate semi IPNs also have good thermal stability and the softening temperatures of the IPNs are significantly, higher than those of the corresponding thermoplastics.     

Specific retroactive interference in modified recognition tests: Evidence for an unknown cause of interference.

McCloskey and Zaragoza (1985a) have recently argued that all item-specific retroactive interference (RI) can be attributed to response bias or demand characteristics. These sources of RI were eliminated in the present studies by a modified recognition test that excluded the interpolated item. Nature pictures were shown; some were followed by related pictures (experimental), and others were followed by dissimilar pictures (control). When forced to choose between two related pictures (the original and a new picture), the original picture was chosen more often for control than for experimental items (Experiments 1 and 2). Paired-associate studies were cited that have found RI in analogous matching recognition tests. These findings contradict McCloskey and Zaragoza's conclusion and must be attributed to some other cause of item-specific RI, such as trace alteration (e.g., Loftus, 1979). Experiments 3 and 4 showed that most items must be accessible in order to detect RI in the forced-choice modified test. However, even with sensitive measures, RI has not always been found in modified recognition. Suggestions are offered to explain the discrepant results. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Rapid and comprehensive indicator for evaluation of performance of treatment processes and of river waters.

Naturally occurring UV active compounds, commonly present in almost all source waters, can be rapidly monitored by their ultraviolet absorbance at 260 nm (E260). Herein, the extent of correlation between the E260 and the removal efficiency of the hazardous contaminants, endocrine disrupters and dioxins, were investigated using various treatment and river source waters. The detection of various types of hazardous contaminants using sophisticated analytical methods, such as high resolution gas chromatography (HRGC)/high resolution mass spectrometry (HRMS) and high performance liquid chromatography (HPLC)/inductively coupled plasma (ICP)/mass spectrometry (MS), as well as various short-term bioassays, can require hours or even days for results to be obtained. The removal of the E260 correlated well with those of individual contaminants, such as endocrine disruptor chemicals and dioxins, with the various treatment processes employed. In the plots of the endocrine disrupters against the DOC/E260, a correlation was found with the endocrine activity of the Korean/Japanese river waters employed in this study.     

Influence of residual milk-clotting enzyme and proteolysis on melting properties of soft cheese

In this work, we assessed the influence of coagulant residual activity and primary proteolysis on Cremoso Argentino cheese melting properties. For that purpose, we made Cremoso soft cheeses using different amounts of coagulant, and also obtained samples in which milk-clotting enzyme was inactivated. Primary proteolysis correlated with residual activity of coagulant in early stages of cheese ripening; however, it was similar in all cheeses after 30 days. The hydrolysis of caseins did not significantly affect the melting ability of the cheeses, expressed as the area increase after heating samples under standardized conditions. Samples with similar proximate composition showed some changes in meltability; those seemed related to pH evolution during ripening.     

Following a path of varying curvature as an output regulation problem

Given a path of nonconstant curvature, local asymptotic stability can be proven for the general n trailer whenever the curvature can be considered as the output of an exogenous dynamical system. The controllers that provide convergence to zero of the tracking error chosen for the path-following problem are composed of a prefeedback that input-output linearizes the system, plus a linear controller.     

Rheology and microstructure of semi-solid aluminum alloys compressed in the drop-forge viscometer

The rheological behavior and microstructure of semi-solid aluminum alloys were studied using a novel apparatus, the drop-forge viscometer (DFV). The viscometer determines force from the second-derivative-of-displacement data with respect to time and permits calculations of viscosities at shear rates in excess of 1000 s⁻¹. Alternatively, the DFV can be operated like a conventional parallel-plate viscometer, attaining shear rates as low as 10⁻⁵ s⁻¹. Rapid compression experiments (in the DFV) result in first rapidly increasing, then decreasing, shear rates. In a typical experiment, the viscosity decreased from about 100 to 1 Pa·s as the shear rate increased from approximately 200 to 1300 s⁻¹ in less than 4 ms. The viscosity later increased to about 10 Pa·s as the shear rate decreased from 1300 to 30 s⁻¹ over 2 ms. The minimum viscosity obtained depended on the maximum shear rate, not the duration of shear. The dual observed phenomena of (1) a very rapid drop of viscosity with increasing shear rate followed by (2) a relatively slow increase of viscosity with decreasing shear rate thereafter have potential significance for future machine and process design. For example, it should be possible to form higher fraction solid slurries than is now feasible by applying vigorous shear to semi-solid slurries just before the metal is introduced to the die entrance. The DFV was used to calculate viscosity as a function of shear rate for samples produced by the commercial strain-induced, melt-activated (SIMA) and magnetohydrodynamic (MHD) methods, as well as the recently developed Massachusetts Institute of Technology (MIT) method. Isothermal experiments were conducted between fraction solid of 0.44 and 0.67 for the various alloys (corresponding to a temperature range of 579 °C to 611 °C). The viscosity of the commercial semi-solid Al-Si alloys A357 and A356 produced by the various methods was similar. Separation of liquid and solid phases was not observed in rapid compression experiments shorter than 10 ms, either visually or with energy-dispersive spectroscopy (EDS) characterization. At low compression velocities, segregation was observed and increased with increasing amounts of strain. The maximum fraction solid compressed at high and low shear rates were 0.67 and 0.69, respectively.