Analysis of feedback for higher order polarization-mode dispersion mitigation of NRZ 40-Gb/s optical transmission

First-order polarization-mode dispersion (PMD) compensation by means of a polarization controller and a differential delay line is not sufficient to guarantee error-free transmission for 40-Gb/s channels when higher order effects severely increase signal distortion. Higher order mitigation is possible by cascading more than one first-order block. However, only two-stage or three-stage devices remain simple enough to be actually controlled. The performance of such higher order PMD compensators is evaluated by means of numerical simulations. Two different feedback signals have been used, demonstrating that first-order and higher order PMD distortion of nonreturn-to-zero (NRZ) pulses at 40 Gb/s can be strongly mitigated for instantaneous values of the differential group delay (DGD) up to the bit slot, when the compensator is properly controlled.     

Dispersion-relation-preserving FDTD algorithms for large-scale three-dimensional problems

We introduce dispersion-relation-preserving (DRP) algorithms to minimize the numerical dispersion error in large-scale three-dimensional (3D) finite-difference time-domain (FDTD) simulations. The dispersion error is first expanded in spherical harmonics in terms of the propagation angle and the leading order terms of the series are made equal to zero. Frequency-dependent FDTD coefficients are then obtained and subsequently expanded in a polynomial (Taylor) series in the frequency variable. An inverse Fourier transformation is used to allow for the incorporation of the new coefficients into the FDTD updates. Butterworth or Chebyshev filters are subsequently employed to fine-tune the FDTD coefficients for a given narrowband or broadband range of frequencies of interest. Numerical results are used to compare the proposed 3D DRP-FDTD schemes against traditional high-order FDTD schemes.     

Modeling aviation baggage screening security systems: a case study

Aviation security protects vital national interests, as well as passengers and aircraft. Key components of an aviation security system include baggage and passenger screening devices and operations. Determining how and where to assign (deploy) such devices can be quite challenging. Moreover, even after such systems are in place, it can be difficult to measure their effectiveness. This paper describes how discrete optimization models can be used to address these questions, based on three performance measures that quantify the effectiveness of airport baggage screening security device systems. These models are used to solve for optimal airport baggage screening security device deployments considering the number of passengers on a set of flights who have not been cleared using a security risk assessment system in use by the Federal Aviation Administration (i.e., passengers whose baggage is subjected to screening), the number of flights in this set, and the size of the aircraft for such flights. Several examples are provided to illustrate these results, including an example that uses data available from the Official Airline Guide.     

Experimental characterisation of the drying effect on uniaxial mechanical behaviour of mortar

The main objective of this present study was to evaluate, for a standard mortar, the drying effect on its mechanical behaviour. Numerous uniaxial compression tests were thus performed with loading-unloading cycles. They were carried out on different samples previously preserved under various conditions of conservation: preserved from desiccation, air drying and rapid drying at 60°C. The obtained results showed significant influences of these conditions on the material behaviour (increase in strength, decrease in Young's modulus and Poisson's ratio) and the necessity of taking into account the coupling effects between mechanical—poromechanical behaviours and drying.     

Gamma-irradiation-induced Ag/SiO2 composite films and their optical absorption properties

Small Ag particles or clusters dispersed mesoporous SiO₂ composite films were prepared by a new method: First the matrix SiO₂ films were prepared by sol-gel process combined with the dip-coating technique, then they were soaked in AgNO₃ solutions followed by irradiation of γ-ray at room temperature and in ambient pressure. The structures of these films were examined by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), and optical absorption spectroscopy. It has been shown that the Ag particles grown within the porous SiO₂ films are very small, and they are isolated and dispersed from each other with very narrow size distributions. With increasing the soaking concentration and an additional annealing, an opposite peakshift effect of the surface plasmon resonance (SPR) was observed in the optical absorption measurements.     

Polarizational Frequency-Selective Multipath Interference Devices for Millimetric- and Submillimetric-Wave Receivers

Variants are considered of palarizational frequency-selective multipath interference devices for millimetric- and submillimetric- wave receivers. Main expressions are presented that describe their characteristics. Advantages are pointed out of the devices as compared with Fabry-Perot interferometers when solving problems of received frequency-band shaping, heterodyne noise rejection, and signal- and heterodyne-radiation transfer to mixer.     

Low Temperature Physics at the Laboratoire National des Champs Magnétiques Pulsés in Toulouse

An overview over past and present activities and future developments at the Toulouse pulsed magnetic field facility is given, both as far as technical developments of the infrastructure, as well as low temperature physics performed at the LNCMP are concerned.     

Analysis of the mechanism of die soldering in aluminum die casting

A mechanism of soldering of an aluminum alloy die casting to a steel die is proposed. A soldering critical temperature is postulated, at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. The liquid joins the die with the casting upon solidification. The critical temperature is determined by the elements in both the casting alloy and the die material and is equal to the solidus temperature of the resulting alloy. The critical temperature is used to predict the onset of die soldering, and the local liquid fraction is related to the soldering tendency. Experiments have been carried out to validate the concept and to determine the critical temperature for die soldering in an iron-aluminum system. Thermodynamic calculations are used to determine the critical temperature and soldering tendency for the cases of pure aluminum and a 380 alloy in a steel mold. Factors affecting the soldering tendency are discussed, and methods for reducing die soldering are suggested.     

Sorting Second-Grade Students: Differentiating Those Retained From Those Promoted.

A cohort of 2nd-grade students provided comparisons of academic and social competence based on school retention/promotion decisions. Sample groups were (a) retained, (b) at risk for retention, (c) special education, and (d) promoted. Findings suggested most children with academic deficiencies are identified by schools early and are sorted into educational treatments differing in intensity that represent a continuum of competence. The authors provide empirical evidence counter to the assumptions that retained students have the requisite ability to catch up and have more problem behaviors than other low-achieving students. The relevance of high-stakes test scores for promotion/retention decisions and the parallels between schools' implementation of retention policy and implementation of regulations for identifying children with disabilities are included in the discussion. (PsycINFO Database Record (c) 2010 APA, all rights reserved)