Reduction of thermal effects in a diode-end-pumped, composite Nd:YAG rod with a sapphire end

We present what is to our knowledge the first theoretical and experimental estimation of the thermal characteristics of a composite Nd:YAG rod with an Al(2)O(3) (sapphire) end in diode-end-pumped geometry. The peak temperature rise in the active segment is calculated to be reduced to 66% and the focal length of the thermal lens was measured to be reduced by 20% compared with a noncomposite Nd:YAG rod. By using a composite rod we successfully demonstrated the improvement of high-power performance that is due to reduction of thermally induced birefringence, which has not been observed in a composite rod with an undoped YAG end.     

Carbonization properties of carbonaceous substances oxidized by air blowing—I: Carbonization behaviors and chemical structure of residual oils oxidized by air blowing

The carbonization process of oxidized oils was investigated by the successive observation of the cokes at several intermediate stages with particular attention to the cocarbonization compatibility of the components, in order to understand how the medium mosaic texture was developed from the oxidized oils. When the oxidized oil was carbonized, very small anisotropic spheres appeared in the matrix, but, being fixed into the mosaic texture, they formed clusters with limited growth of their diameters. The n-hexane insoluble (nHI) and the n-hexane soluble (nHS) components in the, oxidized oil produced isotropic and flow textures in the cokes, respectively. These components did not allow the smooth growth of the anisotropic spheres because of their poor compatibility. Cocarbonization with some proper additives was found effective both in developing a flow texture from the nHI of the oxidized oil and producing a high coke yield. Chemical analyses of the components were performed in order to explain the compatibility.     

Photocatalytic partial oxidation of methylpyridine isomers on TiO2 particles under an anaerobic condition

Photocatalytic oxidation of methylpyridine isomers (2-methylpyridine, 3-methylpyridine, and 4-methylpyridine) was investigated in a mixed solution of acetonitrile and water or acetonitrile using various kinds of TiO₂ powders as photocatalysts. The main products from methylpyridine isomers were pyridinecarboxaldehyde isomers (2-pyridinecarboxaldehyde, 3-pyridinecarboxaldehyde, and 4-pyridinecarboxaldehyde). Rutile large TiO₂ particles showed the highest level of activity for oxidation of 2-methylpyridine probably because band bending was necessary for the oxidation of 2-methylpyridine. On the other hand, a fine particle having an anatase or rutile phase showed a higher level of activity than large TiO₂ particles for oxidation of 3-methylpyridine. A rutile fine particle showed the highest level of activity for the reaction. It was found that pure rutile or pure anatase particles were inactive for oxidation of 4-mathylpyridine. If the particles are not extremely small, pure rutile and pure anatase powders show fairly high levels of activity, and those containing both anatase and rutile phases show the highest level of activity. The activity of pure rutile particles was also enhanced by physically mixing them with a small amount of small anatase particles, which were inactive for this reaction. These results can be explained by the synergism between rutile and anatase particles. All of these reactions effectively proceeded even under anaerobic conditions. Photocatalytic reduction of methylpyridine isomers concomitantly proceeded on TiO₂ particles under the conditions used. These results suggest that the activities of TiO₂ photocatalysts for oxidation of methylpyridine isomers are dominated by the oxidation potential of alkylpiridine and band bending of TiO₂ particles.     

Monitoring behaviour of catabolic genes and change of microbial community structures in seawater microcosms during aromatic compound degradation

The behaviour of microbial populations responsible for degradation of the aromatic compounds, phenol, benzoate, and salicylate, and changes of microbial community structures in seawater microcosms were analysed quantitatively and qualitatively using MPN–PCR and PCR–DGGE. The purpose of the study was to investigate the ecology of the entire microbial community during bioremediation. Bacterial populations possessing catechol 1,2-dioxygenase (C12O) DNA were evidently the primary degraders of phenol and benzoate, but others possessing catechol 2,3-dioxygenase (C23O) DNA increased to enhance substrate degradation under high-load conditions when the substrates were present for long periods. However, salicylate degradation was evidently facilitated by specific bacterial populations possessing C23O DNA. PCR–DGGE analyses suggested that bacterial populations already relatively dominant in the original microcosm contributed to phenol degradation. Bacteria composing a minor fraction of the original population apparently increased and contributed to benzoate degradation. Bacterial populations possessing C23O DNA were responsible for salicylate degradation, however, and different degrading bacteria were evidently selected for, depending on the initial salicylate concentration. Microbial community structure tended to be simplified by aromatic compound degradation. Thus, microbial monitoring can elucidate the behaviour of bacterial populations responsible for aromatic compound degradation and be used to assess the effects of bioremediation on intact microbial ecosystems.     

Theoretical analysis of transient recovery voltages when clearing a transformer secondary fault

An analytical formula for the transient recovery voltage and its derivative dv/dt across a circuit breaker has been derived for the case of a transformer secondary fault. A comparison of the calculated results with field test and EMTP simulation results has demonstrated it to have satisfactory accuracy. By applying the formula, the effects of various circuit parameters on the transient recovery voltage and its derivative dv/dt are elucidated. The derivative dv/dt, defined conventionally as the ratio of the crest value and the time to the crest, is found to be about two‐thirds of the maximum value of dv/dt given as a function of time. In addition, a formula for the critical circuit parameters at which dv/dt across a vacuum circuit breaker reaches the critical condition, that is, the circuit breaker fails to interrupt a fault current, is derived. © 2000 Scripta Technica, Electr Eng Jpn, 134(3): 44–52, 2001     

Field test and EMTP simulation of transient voltages when clearing a transformer secondary fault

A field test was carried out to investigate a fault clearing transient due to current interruption of a three‐phase to ground fault at the secondary side of a 3‐MVA, 22/6.6‐kV transformer by a vacuum circuit breaker. EMTP simulations in comparison with the measured results have made it clear that the capacitance C_p of a CR divider to measure voltages reduces dv/dt of transient recovery voltage across the circuit breaker by the ratio of (C_t/(C_t + C_p) where C_t is the transformer stray capacitance. The leakage inductance evaluated from the transformer rating has been found to be noticeably greater than that determined from the measured fault current possibly due to the transformer saturation. Considering the transformer magnetizing conductance and selecting an appropriate interrupted current, EMTP simulation gives a satisfactory result compared with a field test. © 1999 Scripta Technica, Electr Eng Jpn, 130(2): 40–48, 2000     

Convective heat transfer of horizontal spherical particle layer heated from below and cooled from above Part II: Effect of thickness of particle layer

Convection heat transfer and pressure drop measurements were performed with a rectangular duct, having a cooled upper and a heated lower surface, which was packed with spherical particles. Air was used as the test fluid and four kinds of spherical particles having different diameters and thermal conductivities were used as the packing materials. The ratio of the diameter of the spherical particle to the distance between the cooled and heated surfaces, d/H, was varied from 0.173 to 1. The thermal conductivity of the particle layer was also measured under the still air condition. The thermal conductivity of the particle layer was not affected by the value of d/H. In the case of the one-stage arrangement of spherical particles (d/H = 1), the flow resistance took on a remarkably small value compared with the flow resistance of a homogeneous spherical particle layer. Moreover, the flow resistance of the particle layer formed with some layers of particles could be predicted by combining the flow characteristics of the one-stage particle layer and that of the homogeneous spherical particle layer. The heat transfer coefficient of the particle layer was larger than that of turbulent air flow on a flat plate. At a constant superficial air velocity, there existed a value of d/H which gave a maximum value of the average heat transfer coefficient. Nondimensional heat transfer correlation equations were derived in terms of parameters expressing the average characteristics of the spherical particle layers. © 1998 Scripta Technica, Heat Trans Jpn Res, 26(3): 176–192, 1997     

Fast drive of displacement magnification mechanism with flexure hinge using loading type impact damper

A displacement magnification mechanism which uses flexure motion guide using elastic hinges can realize smooth frictionless motion but has poor vibration damping capability. An impact damper is a damping mechanism which uses collision energy to dissipate vibration energy. If the damper is used for vibration control of the flexure mechanism, it may be able to dissipate unexpected vibration without killing the merits of the flexure mechanism. In the paper, a loading type impact damper is applied to settle down transient vibration of a displacement magnification mechanism. We investigate differences of damping effect by setting conditions of the damper. It is shown that the impact damper can eliminate residual vibration at step response effectively without steady state error. The experimental displacement magnification mechanism with impact damper can settle down less than 1/5 of the response without the damper under appropriate setting conditions. Influence of natural frequency ratio between damper and displacement magnification mechanism is investigated. Influences of indentation at impact point are also examined.     

Electrochemical properties of LiPON films made from a mixed powder target of Li3PO4 and Li2O

Lithium phosphorus oxynitride (LiPON) films were prepared by radio frequency magnetron sputtering. In order to control the atomic composition of the films, a mixture of Li₃PO₄ and Li₂O powders was used as the sputtering target. The ionic conductivity of the films showed a maximum (6.4 × 10^− 6 S/cm) when the molar ratio of Li₃PO₄ to Li₂O in the target was 1:2. The films formed from a target not containing Li₂O showed good durability in air at the expense of slightly poorer ionic conductivity. This is probably due to the amount of Li in the film being significantly less which effectively suppressed absorption of CO₂ in air.     

Physician-received scatter radiation with angiography systems used for interventional radiology: comparison among many X-ray systems

Radiation protection for interventional radiology (IR) physicians is very important. Current IR X-ray systems tend to use flat-panel detectors (FPDs) rather than image intensifiers (IIs). The purpose of this study is to test the hypothesis that there is no difference in physician-received scatter radiation (PRSR) between FPD systems and II systems. This study examined 20 X-ray systems in 15 cardiac catheterisation laboratories (11 used a FPD and 9 used an II). The PRSR with digital cineangiography and fluoroscopy were compared among the 20 X-ray systems using a phantom and a solid-state-detector electronic pocket dosemeter. The maximum PRSR exceeded the minimum PRSR by ~12-fold for cineangiography and ~9-fold for fluoroscopy. For both fluoroscopy and digital cineangiography, the PRSR had a statistically significant positive correlation with the entrance surface dose (fluoroscopy, r = 0.87; cineangiography, r = 0.86). There was no statistically significant difference between the average PRSR of FPDs and IIs during either digital cineangiography or fluoroscopy. There is a wide range of PRSR among the radiography systems evaluated. The PRSR correlated well with the entrance surface dose of the phantom in 20 X-ray units used for IR. Hence, decreasing the dose to the patient will also decrease the dose to staff.