Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Molecular weight effect on the obtainment of parallel and perpendicular orientation in thermotropic poly(diethylene glycol <Emphasis Type="Italic">p,p′</Emphasis>-bibenzoate)

Summary The effect of molecular weight on the uniaxial orientation process has been analyzed in two samples of thermotropic poly(diethylene glycol p,p′-bibenzoate), evaluating the influence of that parameter on the type of orientation obtained. Several strain rates and deformation temperatures have been tested in order to map out the conditions for obtaining the two different kinds of orientation. The results show that in the lower molecular weight PDEB sample (M_w=31200) it is rather easy to get exclusively perpendicular “anomalous” orientation, with the molecular axes aligned transversely to the stretching direction. However, it is extremely difficult to obtain 100% parallel “normal” orientation. On the contrary, either type of orientation or a mixture of them can be easily developed for the higher molecular weight PDEB sample (M_w=102900).     

Simultaneous sulfide and acetate oxidation under denitrifying conditions using an inverse fluidized bed reactor

BACKGROUND: Simultaneous removal of sulfur, nitrogen and carbon compounds from wastewaters is a commercially important biological process. The objective was to evaluate the influence of the CH₃COO^?/NO₃^? molar ratio on the sulfide oxidation process using an inverse fluidized bed reactor (IFBR). RESULTS: Three molar ratios of CH₃COO^?/NO₃^? (0.85, 0.72 and 0.62) with a constant S^2?/NO₃^? molar ratio of 0.13 were evaluated. At a CH₃COO^?/NO₃^? molar ratio of 0.85, the nitrate, acetate and sulfide removal efficiencies were approximately 100%. The N₂ yield (g N₂ g^?1 NO₃^?‐N consumed) was 0.81. Acetate was mineralized, resulting in a yield of 0.65 g inorganic‐C g^?1 CH₃COO^?‐C consumed. Sulfide was partially oxidized to S⁰, and 71% of the S^2? consumed was recovered as elemental sulfur by a settler installed in the IFBR. At a CH₃COO^?/NO₃^? molar ratio of 0.72, the efficiencies of nitrate, acetate and sulfide consumption were of 100%, with N₂ and inorganic‐C yields of 0.84 and 0.69, respectively. The sulfide was recovered as sulfate instead of S⁰, with a yield of 0.92 g SO₄^2?‐S g^?1 S^2? consumed. CONCLUSIONS: The CH₃COO^?/NO₃^? molar ratio was shown to be an important parameter that can be used to control the fate of sulfide oxidation to either S⁰ or sulfate. In this study, the potential of denitrification for the simultaneous removal of organic matter, sulfide and nitrate from wastewaters was demonstrated, obtaining CO₂, S⁰ and N₂ as the major end products. Copyright © 2008 Society of Chemical Industry     

Grouped Approach for the Design of H.264/AVC Motion Estimation Architectures

This letter presents a novel approach for organizing computational resources into groups within H.264/AVC motion estimation architectures, leading to reductions of up to 75% in the equivalent gate count with respect to state‐of‐the‐art designs.     

Use of recycled copper slag for blended cements

Copper slag is a by‐product generated during smelting to extract copper metal from the ore. The copper slag obtained may exhibit pozzolanic activity and may therefore be used in the manufacture of addition‐containing cements. In this paper the effect of the incorporation of the copper slag in cement is measured. Blends of copper slag with Portland cement generally possess properties equivalent to Portland cement containing fly ash, but very different to the silica fume incorporation. Copper slag and fly ash reduce the heat of hydration more effectively than silica fume in mortars. The replacement of 30% cement by copper slag reduces the flexural and compressive strength in a similar way to fly ash; however, after 28 days, the reduction is less than the percentage of substitution. Hydrated calcium aluminate phases were analysed using scanning electron microscopy (SEM) and X‐ray diffraction (XRD) techniques. The pozzolanic activity of copper slag is similar to that of fly ash and higher than silica fume. In the presence of low water/cement ratios, certain pozzolanic materials produce a very compact cement paste that limits the space available for hydration products, a determining factor in the formation of hydrated calcium aluminates. SEM was found to be a useful analytical technique when aluminates are formed and can be clearly detected by XRD. Copyright © 2008 Society of Chemical Industry     

Time Decay of the Activity of the Reduction Reaction of NO by CO on a Pd/Al2O3 Catalyst

An experimental study is made of the time decay of activity of the CO–NO reaction on a Pd/Al₂O₃ looking at the effect on reaction order and apparent activation energy. The optimum kinetics parameters fitting the steady state data at moderate pressures are determined. The time decay curves are analyzed through various catalyst deactivation models.     

Manifold mapping: a two-level optimization technique

In this paper, we analyze in some detail the manifold-mapping optimization technique introduced recently [Echeverría and Hemker in space mapping and defect correction. Comput Methods Appl Math 5(2): 107—136, 2005]. Manifold mapping aims at accelerating optimal design procedures that otherwise require many evaluations of time-expensive cost functions. We give a proof of convergence for the manifold-mapping iteration. By means of two simple optimization problems we illustrate the convergence results derived. Finally, the performances of several variants of the method are compared for some design problems from electromagnetics.