Aluminium electrodeposition from AlCl3-NaCl melts on glassy carbon,platinum and gold electrodes

The electrochemical deposition and dissolution of aluminium on glassy carbon, platinum and gold electrodes in chloraluminate melts have been investigated using linear sweep voltammetry and potentiostatic pulse techniques. It was shown that deposition of aluminium on the glassy carbon electrode at low overpotentials takes place by 3-D progressive nucleation and growth, with the incorporation of atoms in the crystal lattice as the rate-determining step. At overpotentials higher than –100 mV vs Al, in the melts containing more than 52 mol % of AlCl₃, diffusion of Al₂Cl ₇ ^– , takes over the control of deposition of aluminium. Alloying of platinum and gold electrodes with aluminium from the melt occurs in the underpotential region.     

Permeation study on the hollow-fiber supported liquid membrane for the extraction of Cobalt(II)

The transport of Co(II) through hollow-fiber-supported liquid membrane containing di-(2-ethylhexyl) phosphoric acid (D2EHPA) diluted in kerosene was examined. The mass transfer rate, expressed as permeability, P, focused on diffusion through the aqueous layer in the feed solution, the organic layer and the aqueous layer in the stripping solution. Experiments were performed as a function of aqueous feed solution velocity (100-500 ml/min), carrier concentration (0.1-20% v/v), aqueous stripping solution velocity (100-1,000 ml/min) and feed concentration (100-1,000 ppm) with 0.1 M HCl in the product phase. pH of the feed solution was 5.0. The measured permeabilities were compared to generally accepted mass transfer correlations. The validity of the prediction was evaluated with the experimental data, and the data were found to tie in well with the theoretical values. The model is the reported describing that the rate limiting step in the transport of the ion was the diffusion through both aqueous films, feed and stripping, whereas the organic resistance of the membrane was negligible. From this study, the model has good potential for the prediction of permeability of Co(II).     

Voltammetric and galvanostatic studies of hydrous and anhydrous iridium oxide films

Electrolytically grown hydrous oxide films on iridium wire electrodes have been thermally treated from 473 to 773 K. Anhydrous oxide films formed by this treatment have been subjected to cathodic polarization at the potential of the hydrogen evolution reaction, square-wave pulsing of potential from –0.25 to +1.25 V with respoect to SCE and to anodic galvanostatic polarization in 0.5 mol dm^–3 H₂SO₄. Cathodic pretreatment caused an increase of the voltammetric charge in the oxide formation region while the square-wave pulsing formed a hydrous oxide film whose voltammetric charge was superimposed on the charge of the anhydrous oxide film. Both procedures restored the hydrophilic nature of the electrode/solution interface. Potential-time curves during anodic galvanostatic polarization served as a diagnostic criterion for the stability and the state of the oxide film.     

Contribution to the hydration of expansive cement on the basis of metakaolinite

The study of hydration of expansive cement prepared from 64% portland cement clinker, 23% metakaolinite and 13% CaSO₄.2H₂O is described. It was found that in the course of a 10-day hydration period, all the gypsum entered the reaction with the formation of ettringite. In 7–10 days, after the termination of the expansion processes, typical stalk-like crystals were transformed into leaf-shaped or other formations. Ettringite was identified even after 4 months of hydration. Monosulphate (3CaO.Al₂O₃.CaSO₄.12H₂O) was found in none of the investigated high-expansion cement paste samples.     

Effects of aging on polyimide: A study of bulk and interface chemistry

We are investigating the bulk and interfacial chemistry of polyimide (PI) exposed to heat and relative humidity (RH) stress (85°C/85% RH) over long periods to understand the long-term reliability aspects of PI for microelectronic applications. The PI surface chemistry and the PI–Si interface chemistry was followed with electron spectroscopy for chemical analysis (ESCA). For exposure times greater than 550 h, the PI surface exhibits significant changes in emission structure and atomic concentration. The PI–Si interface indicates little change in the PI chemistry when compared to control samples. The water-contact angle at the PI surface shows no statistically significant change as a function of exposure time. Bulk and surface chemistry were followed with Fourier transform infrared spectroscopy (FTIR) in a grazing incidence reflection configuration. There were measurable differences in FTIR spectra between aged and control samples only for the case of very thin PI layers. These results suggest that for exposure times of less than 1100 h, chemical changes in PI occur primarily at the PI–air interface for samples 1 μm thick and greater. These changes represent a possible rearrangement of the imide structure and may be a form of deimidization of the polymer, but the final state is not polyamic acid. The PI surface chemistry changes observed with ESCA are reversible upon reheating to the cure temperature.     

Purification of 2-mercaptobenzothiazole by solvent extraction

−Purification of 2-mercaptobenzothiazole (91.9% purity) by solvent extraction was studied. The extraction of impurities present in crude 2-MBT (e.g. benzothiazole, sulfides and sulfur containing compounds) was carried out at temperatures between 70-180°C using various solvents and their mixtures of different polarity. The highest purity of 2-MBT, above 99% was obtained using nitrobenzene, toluene and ethanol, even at a concentration of 2-MBT above 50 wt%. Increasing temperature and decreasing concentration of the raw material have a positive influence on the purification process. A comparable efficiency of purification was observed also with mixed solvents, (toluene with ethanol, acetone and aniline) possessing the same polarities. A correlation between the polarity indexes (PI) of mixed solvents and experimentally obtained purity of 2-MBT was found. The highest purity of 2-MBT provides extraction of the raw material with mixed solvents having PI 3.8-4.4.     

Using static suffix array in dynamic application: Case of text compression by longest first substitution

Over the last decade, enhanced suffix arrays (ESA) have replaced suffix trees in many applications. Algorithms based on ESAs require less space, while allowing the same time efficiency as those based on suffix trees. However, this is only true when a suffix structure is used as a static index. Suffix trees can be updated faster than suffix arrays, which is a clear advantage in applications that require dynamic indexing. We show that for some dynamic applications a suffix array and the derived LCP-interval tree can be used in such a way that the actual index updates are not necessary. We demonstrate this in the case of grammar text compression with longest first substitution and provide the source code. The proposed algorithm has O(N²)$O(N^2)$ worst case time complexity but runs in O(N)$O(N)$ time in practice.     

Developing a model to assess the success of e-learning systems: evidence from a manufacturing company in transitional economy

This paper examines the success of an e-learning system in a company from the perspective of employees by using a multimethod approach. For this purpose Moodle learning management system was used. The success of e-learning as an information system was evaluated using four constructs of the updated DeLone and McLean IS success model—system quality, use, user satisfaction and net benefits, and adding one more construct—user performance. In this research a combination of observation and survey as two different research methods was used, which allowed the new measure to be incorporated into the model. Empirical assessment was carried out by exploratory factor analysis, confirmatory factor analysis and structural equation modeling. The research model was found to be valid and reliable. The results provide an expanded understanding of the constructs that measure the success of an e-learning system, helping to more deeply understand the key success dimensions and their interrelationships. The implications of our work were discussed. The DeLone and McLean IS success model applied equally well. However, the use of observation as a method of data collection revealed the weaknesses of the original model.     

Small‐signal and noise modeling of class of HEMTs using knowledge‐based artificial neural networks

In this article, the neural network approach is exploited for development of bias‐dependent small‐signal and noise models of a class of microwave field effect transistor (FETs) made in the same technology but differing in the gate width. The prior knowledge neural approach is applied. Introducing gate width at the input of proposed neural networks, as well as the S/noise parameters of a device that belongs to the same class as the modeled device representing the prior knowledge, leads to very accurate scattering and noise parameters' modeling, as exemplified by modeling of class of pseudomorphic high electron mobility transistor (pHEMT) devices. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.