Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Modeling and verification of the double frequency effect using a MEMS device

The derivation, verification, and implication of the nonlinear dynamic and frequency response of electrostatic actuator due to the double frequency effect (DFE) were reported in this study. In particular, an extra mode called half mode was observed and measured in various studies. However, a complete in-depth discussion of the effect was not reported in the past. In the present study, a second-order dynamical equation was adapted firstly to model the dynamic and frequency response of electrostatic actuator where typical harmonic input signal with a dc bias was used. Secondly, by solving the equation, complex waveform in dynamic response and an extra half mode in frequency response due to the double frequency effect can be observed and discussed. To verify the simulated result, an electrostatic driving device was fabricated using PolyMUMPS^© process. Note that in frequency response, when dc bias is equal to the amplitude of ac signal, simulated and experimental results indicated that the amplitude of half mode was one-fourth of first mode.     

硫化物预处理方法研究及测定中的质量保证

针对水和废水中硫离子的特点,设计制作了测定硫化物的酸化—吹气—吸收预处理装置,并验证了该装置对硫化物的回收效果,简化了原来的预处理方法。总结分光测定过程中注意的若干事项,确定了最佳实验条件,使该方法具有更准确、简便、快速的特点。     

Colloidal Synthesis of Hollow Cobalt Sulfide Nanocrystals

Formation of cobalt sulfide hollow nanocrystals through a mechanism similar to the Kirkendall Effect has been investigated in detail. It is found that performing the reaction at > 120 °C leads to fast formation of a single void inside each shell, whereas at room temperature multiple voids are formed within each shell, which can be attributed to strongly temperature‐dependent diffusivities for vacancies. The void formation process is dominated by outward diffusion of cobalt cations; still, the occurrence of significant inward transport of sulfur anions can be inferred as the final voids are smaller in diameter than the original cobalt nanocrystals. Comparison of volume distributions for initial and final nanostructures indicates excess apparent volume in shells, implying significant porosity and/or a defective structure. Indirect evidence for fracture of shells during growth at lower temperatures was observed in shell‐size statistics and transmission electron microscopy images of as‐grown shells. An idealized model of the diffusional process imposes two minimal requirements on material parameters for shell growth to be obtainable within a specific synthetic system.     

Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.     

Effects of surface charge, micro-bubble size and particle size on removal efficiency of electro-flotation.

Flotation is a water treatment alternative to sedimentation, and uses small bubbles to remove low-density particles from potable water and wastewater. The effect of zeta potential, bubble size and particle size on removal efficiency of the electro-flotation process was investigated because previous model-simulations indicated that these attributes are critical for high collision efficiency between micro-bubbles and particles. Solutions containing Al3+ as the metal ion were subjected to various conditions. The zeta potentials of bubbles and particles were similar under identical conditions, and their charges were influenced by metal ion concentration and pH. Maximum removal efficiency was 98 and 12% in the presence and absence of flocculation, respectively. Removal efficiency was higher when particle size was similar to bubble size. These results agree with modelling simulations and indicate that collision efficiency is greater when the zeta potential of one is negative and that of the other is positive and when their sizes are similar.     

Cover Picture: Arresting,Fixing, and Separating Dimers Composed of Uniform Silica Colloidal Spheres (Adv. Funct. Mater. 12/2006)

In colloidal suspensions of silica, particles undergo constant collisions. By controlling various parameters, the repulsive barrier can be reduced, thereby substantially increasing the number of collision‐induced dimerization events. Xia and co‐workers report on p. 1627 that the dimers could be arrested and then permanently fixed by introducing a small amount of fresh tetraethylorthosilicate into the colloidal suspension, with monodisperse dimer yields of up to 50 %. This yield could be increased to 80 % by centrifugation in a density gradient medium. When fresh tetraethylorthosilicate is introduced into a colloidal suspension of silica spheres, it hydrolyzes and condenses in situ to arrest and fix the dimers resulting from constant collisions between the spheres. By optimizing the experimental parameters (including the length of aging time) and the diameter of the silica spheres, as well as the concentrations of counterions, water, and ammonia, it is possible to routinely produce monodisperse dimers with a yield as high as 50 %. When combined with centrifugation using a density gradient medium, the yield of such dimers could be further increased to 80 %. It is believed that this method will provide a simple and versatile approach to the high‐volume production of dimers from spherical colloids composed of different materials. These dimers may find widespread use in a range of applications such as fabrication of photonic crystals and fundamental studies related to colloidal science.