Mechanical Property of HVOF Inconel 718 Coating for Aeronautic Repair

The module of elasticity is one of the most important mechanical properties defining the strength of a material which is a prerequisite to design a component from its early stage of conception to its field of application. When a material is to be thermally sprayed, mechanical properties of the deposited layers differ from the bulk material, mainly due to the anisotropy of the highly textured coating microstructure. The mechanical response of the deposited layers significantly influences the overall performance of the coated component. It is, therefore, of importance to evaluate the effective module of elasticity of the coating. Conventional experimental methods such as microindentation, nanoindentation and four-point bending tests have been investigated and their results vary significantly, mainly due to inhomogeneous characteristics of the coating microstructure. Synchrotron radiation coupled with a tensile test rig has been proposed as an alternative method to determine the coating anisotropic elastic behavior dependence on crystallographic orientations. The investigation was performed on Inconel 718 (IN718) HVOF coatings sprayed on IN718 substrates. Combining these experimental techniques yield a deeper understanding of the nature of the HVOF coating Young’s modulus and thus a tool for Design Practice for repair applications.     

Mass Spectrometry-Based Proteomics Reveal Alcohol Dehydrogenase 1B as a Blood Biomarker Candidate to Monitor Acetaminophen-Induced Liver Injury

Acute liver injury (ALI) is a severe disorder resulting from excessive hepatocyte cell death, and frequently caused by acetaminophen intoxication. Clinical management of ALI progression is hampered by the dearth of blood biomarkers available. In this study, a bioinformatics workflow was developed to screen omics databases and identify potential biomarkers for hepatocyte cell death. Then, discovery proteomics was harnessed to select from among these candidates those that were specifically detected in the blood of acetaminophen-induced ALI patients. Among these candidates, the isoenzyme alcohol dehydrogenase 1B (ADH1B) was massively leaked into the blood. To evaluate ADH1B, we developed a targeted proteomics assay and quantified ADH1B in serum samples collected at different times from 17 patients admitted for acetaminophen-induced ALI. Serum ADH1B concentrations increased markedly during the acute phase of the disease, and dropped to undetectable levels during recovery. In contrast to alanine aminotransferase activity, the rapid drop in circulating ADH1B concentrations was followed by an improvement in the international normalized ratio (INR) within 10–48 h, and was associated with favorable outcomes. In conclusion, the combination of omics data exploration and proteomics revealed ADH1B as a new blood biomarker candidate that could be useful for the monitoring of acetaminophen-induced ALI.     

Stress corrosion cracking susceptibility of P285NH and API 5L X65 steel grades in the high-level radioactive waste repository cell concept

Since 2014, the concept developed for the disposal of high-level radioactive waste in the French deep geological repository project Cigéo includes a cement-based grout material. This cement-based grout material will be injected between the casing and the claystone to neutralize the potential acidity resulting from the claystone oxidation induced by the drilling process of the disposal cell. In these conditions of pH (around 10.5) and temperature (90°C, maximum expected during the disposal), the metallic materials could be sensitive to stress corrosion cracking (SCC). In this project, different environments (aerated or deaerated, at room temperature or at 90°C) and synthetic solutions are considered to reproduce the different periods expected during the long life repository. The project is based on electrochemical measurements (polarization curves to define the SCC critical domain of potentials), slow strain rate tensile tests, and long-term immersion for crack initiation and propagation tests.     

Spark plasma sintering of double-walled carbon nanotubes

Bulk samples of double-walled carbon nanotubes are prepared for the first time. The best spark plasma sintering conditions are (1100 °C, 100 MPa). Raman spectroscopy and scanning electron microscopy show that the nanotubes are undamaged. The density is equal to 1.29 g cm⁻³ and the pores are all below 6 nm in diameter. The electrical conductivity is equal to 1650 S cm⁻¹. The transverse fracture strength is equal to 47 MPa.     

A predictive hybrid force modeling in turning: application to stainless steel dry machining with a coated groove tool

The International Journal of Advanced Manufacturing Technology - This paper presents an hybrid numerical/analytical modeling for estimation of cutting forces in machining process. The approach...     

Hydrodynamic characteristics of gas–solid fluidization at high temperature

Effect of temperature on the hydrodynamics of bubbling gas–solid fluidized beds was investigated in this work. Experiments were carried out at different temperatures ranged of 25–600°C and different superficial gas velocities in the range of 0.17–0.78 m/s with sand particles. The time‐position trajectory of particles was obtained by the radioactive particle tracking technique at elevated temperature. These data were used for determination of some hydrodynamic parameters (mean velocity of upward and downward‐moving particles, jump frequency, cycle frequency, and axial/radial diffusivities) which are representative to solids mixing through the bed. It was shown that solids mixing and diffusivity of particles increases by increasing temperature up to around 300°C. However, these parameters decrease by further increasing the temperature to higher than 300°C. This could be attributed to the properties of bubble and emulsion phases. Results of this study indicated that the bubbles grow up to a maximum diameter by increasing the temperature up to 300°C, after which the bubbles become smaller. The results showed that due to the wall effect, there is no significant change in the mean velocity of downward‐moving clusters. In order to explain these trends, surface tension of emulsion between the rising bubble and the emulsion phase was introduced and evaluated in the bubbling fluidized bed. The results showed that surface tension between bubble and emulsion is increased by increasing temperature up to 300°C, however, after that it acts in oppositely.     

Interface step-induced thin-film delamination and buckling

Atomistic simulations based on experimental observations provide the first evidence that the interface delamination of a thin film from its substrate may start from interface steps. Buckling of the film after interface gliding from both edges of its delaminated part is also observed. In the framework of the Föppl–von Kármán theory of thin plates, the expression of the critical strain beyond which the film buckles has been then analytically determined as a function of the step height and gliding displacements. Both numerical and analytical results confirm that the formation of blisters is favoured in the neighbourhood of interfacial imperfections.     

Modification of hydrophobic/hydrophilic properties of Vulcan XC72 carbon powder by grafting of trifluoromethylphenyl and phenylsulfonic acid groups

Carbon supports (glassy carbon and Vulcan XC72 powder) were modified by electrochemical and spontaneous grafting of phenylsulfonic acid (PSA) or trifluoromethylphenyl (TFMP) groups via diazonium ion reduction. The effectiveness of the grafting was confirmed electrochemically, by XPS measurements and elemental analyses. The hydrophobic or hydrophilic character of carbon surfaces was evidenced by measuring the contact angles of drops of different liquids (water, ethylene glycol and glycerol) in heptane. The surface energy was calculated and it was found, for example, that spontaneous grafting of a glassy carbon surface by PSA groups led to an increase by a factor 20 of the surface energy compared with an unmodified glassy carbon surface. The study of the grafting of such groups on XC72 carbon powder indicated that a very low grafting ratio (in wt%) led to a significant change in the macroscopic properties of the powder. Thermogravimetric analysis coupled with mass spectroscopy measurements (TGA-MS) showed that these grafted layers were thermally stable even in the presence of dispersed platinum nanoparticles. It was shown by cyclic voltammetry that the carbon substrate modification did not affect the electrochemical behavior of platinum catalyst, since the same active surface area was determined on Pt-XC72, Pt-PSA-XC72 and Pt-TFMP-XC72 catalysts.