Direct Instantaneous Torque Control in Direct Drive Permanent Magnet Synchronous Motors—a New Approach

In this paper, a novel direct instantaneous torque control scheme for a direct drive (DD) permanent magnet synchronous motor (PMSM) is presented. A hybrid control structure combining the internal model principle and the variable structure control (VSC) approach is proposed. First, a variable structure torque controller is adopted to regulate the torque angle increment according to the torque feedback error. Second, the appropriate control voltage vector is determined using the reference stator flux vector and the estimated dynamic back electromotive force (EMF) vector, as an internal model, in a deadbeat control manner. Subsequently, better disturbance rejection can be obtained with the proposed cascaded control structure. To robustly obtain the instantaneous torque and flux information, a robust adaptive motor model is proposed. The Lyapunov stability theory is used to analyze the stability of the augmented robust adaptive motor model and to give a guideline for tuning model parameters. Experimental results are presented to demonstrate the validity and effectiveness of the proposed instantaneous torque control scheme.     

Effect of surfactant replacement therapy on the outcome of premature infants with respiratory distress syndrome

Lung surfactant replacement has been tested clinically in recent years. In this study the outcome of 31 premature infants with moderate to severe neonatal respiratory distress syndrome (RDS) treated with surfactant was compared to that of 74 prematures with RDS treated conventionally by positive pressure ventilation and supportive care. The groups were well matched for gestational age, birthweight, sex, and Apgar scores at 1 and 5 min. Surfactant treatment resulted in a significant decrease in mortality--from 36.6% in the untreated group to 12.9% in the surfactant-treated group (P < 0.04). This improvement in survival was seen also in prematures with a birthweight < 1,000 g; in the untreated group mortality was 57.6% compared to 23.5% in the treated group (P < 0.05). The incidence of pneumothorax was lower in the treated group--42% vs. 13% (P < 0.01). Surfactant treatment resulted in a trend of more survivors without bronchopulmonary dysplasia or intraventricular hemorrhage, even though surfactant therapy did not change the incidence of either.     

Adaptive fuzzy fault-tolerant control using Nussbaum-type function with state-dependent actuator failures

Neural Computing and Applications - This paper presents an adaptive fuzzy fault-tolerant tracking control for a class of unknown multi-variable nonlinear systems, with external disturbances,...     

Preparation,Properties and Applications of the Hybrid Organic/Inorganic Nanocomposite Based on Nanoporous Carbon Matrix

Journal of Inorganic and Organometallic Polymers and Materials - Nanoporous carbon matrix was prepared by the sol–gel process from pyrogallol-formaldehyde (PF) mixtures in water using picric...     

SOLUBILITY AND DIFFUSIVITY OF GASES IN AN ORGANIC SOLUTION OF AMINE

Solubilities and diffusivities of carbon dioxide and nitrous oxide in a mixture of toluene and isopropanol organic solution of cyclohexylamine were measured at 20°C in the range of pressures of solute from 1 to 3 bars. This was performed with an original chromatographic technique taking into account the presence of the product of the reaction.     

Extraction of metals from sulphides using sulphur trioxide in fluidised bed

The kinetics of the reaction of chalcopyrite, iron sulphide, copper sulphide, and nickel sulphide with sulphur trioxide gas were studied using a fluidised bed technique. O₂, N₂, or air was used as a carrier gas for the sulphur trioxide in fluidisation. Binary mixtures of finely ground (0.37–75 μm) samples were reacted with the sulphur trioxide in a Pyrex column at 373–673 K. The reaction products were leached with water and the soluble metals in the solution were determined by atomic absorption spectrometry. The total soluble reaction products were determined gravimetrically. The results obtained showed that a higher yield of soluble salts was obtained when O₂ or air was used as a carrier gas for sulphur trioxide than when an inert gas was used. Higher yields of soluble salts were obtained when the samples were most finely ground. Increase of copper sulphide content in binary mixtures with iron or nickel sulphide led to an increase in the yield of soluble salts. For iron sulphide/nickel sulphide mixtures, the yield of soluble salts increased with the nickel sulphide content. There were maximum values for the soluble metal ratios Ni/Fe and Cu/Ni in the corresponding sulphide binary mixtures and this maximum was at about 50% weight. The soluble Cu/Fe ratio increased with copper sulphide content in mixtures with iron sulphide.     

Arylidene polymers. XVIII. Synthesis and thermal behavior of organometallic arylidene polyesters containing ferrocene derivatives in the main chain

A new interesting category of organometallic polyesters based on diarylidenecycloalkanones containing ferrocene derivatives in the polymer main chain has been prepared by interfacial polycondensation of 1,1′-dichlorocarbonyl ferrocene or 1,1′-dichlorocarbonyl-4,4′-diiodoferrocene with 2,5-bis(p-hydroxybenzylidene)cyclopentanone, 2,5-divanillylidenecyclopentanone, 2,6-bis(p-hydroxybenzylidene)cyclohexanone, 2,6-divanillylidenecyclohexanone, and 2,7-bis(p-hydroxybenzylidene) cycloheptanone. The resulting polyesters were characterized by elemental analyses, infrared spectroscopy, solubility, and viscometry measurements. The thermal behavior of the synthesized polymers was evaluated by thermal gravimetric analysis and correlated with their structures. The crystallinity of all polymers were examined by x-ray diffraction analysis. Moreover, the electrical conductivity of a selected example of polymer was investigated above the temperature range (300–500 K) and showed that it followed an Arrhenius-type equation with activation energy 2.09 eV. © 1993 John Wiley & Sons, Inc.     

Studies on the pulping of egyptian cotton linters by the nitric acid process

Egyptian cotton linters were pulped by the nitric acid process. In order to reduce the high ash and silica contents of the resulting pulps it was found necessary to apply hot refining with sodium hydroxide solution. Different conditions of concentration, temperature, and pressure in the refining step were investigated. Refining before and during bleaching were compared.     

Sintering of Ceramic Particulate Composites: Effect of Matrix Density

Composites consisting of a fine-grained, polycrystalline zinc oxide matrix and <10 vol% coarse, rigid silicon carbide inclusions were prepared by the same mixing procedure and then compacted to produce samples with matrix densities of 0.45 and 0.68 of the theoretical. The samples were sintered under identical temperature profiles in separate experiments that employed either a constant rate of heating of 4°C/min or near isothermal heating at 735°C. The ratio of the densification rate of the composite matrix to the densification rate of the unreinforced zinc oxide was found to be independent of the initial matrix density. This ratio increased significantly with temperature in the constant-heating-rate experiments but was relatively constant in the isothermal experiments. The results indicate that microstructural coarsening may be an important mechanism for explaining the reduced sinterability of polycrystalline matrix composites.     

Numerical and experimental investigation of three-dimensional flow in extrusion dies

The univariant element, Q₁ P₀, and the multivariant elements, QP₀ and R P₀, are compared for the numerical simulation of the flow in extrusion dies. The pressure distribution obtained by using the Q₁ P₀ element was found to be afflicted with the checkerboard pressure mode. On the other hand, the multivariant elements, Q P₀ and R P₀, gave accurate and physically reasonable velocity and pressure distributions. The computed values of the pressure drop across extrusion dies matched well with the pressure drop determined experimentally.