An investigation of sugar extraction methods and the use of microwave power for date syrup processing: efficiency and color related considerations.

This study investigates the effect of extraction methods on the color of date syrup and the potential use of microwave power for syrup processing. Sugar solutions were extracted from dates by boiling, soaking and blending. Color and sugar content of the extracted solutions were measured, and the percentage of sugar extracted form the total fruit sugar determined. Boiling was found to be the most efficient method of extraction whereby 74% of total samples sugar was extracted. In contrast, only 54.2% of fruit sugar was extracted by blending and 42% by soaking. In addition, solutions extracted by soaking and blending had a foaming problem in the subsequent concentration process. The extraction method had no effect on the product final color. The extracted solution was concentrated using two heating methods: conventional and microwave heating at a 600 W capacity and a frequency of 2450 MHz applied at three power levels: 10, 7, and 6. In the heating process, 180 minutes were needed to achieve a 77% degrees Brix using convective heating, while it took 81, 138, and 166 minutes of microwave heating at power level 10, 7, and 6, respectively to achieve the same concentration. Water activity of the syrup was measured within a sugar content range of 50 to 80% degrees Brix and the sugar concentration at which the product is shelf stable was determined at 76%.     

Techniques for microstructural characterization of powder-processed nickel-based superalloys

Methods are described for sample preparation of polycrystalline Ni-based superalloys in order to perform a detailed microstructural characterization. Specific techniques for the precise definition of the various phases present are outlined and these are shown to be useful for the measurement of size, volume fractions and distribution. A number of optical, scanning and transmission microscopy techniques are used to provide the necessary information.     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Hf-doped and NH/sub 3/-nitrided high-K gate dielectric thin film with least drain current degradation and flatband voltage shift

A novel technique to form high-K dielectric of HfSiON by doping base oxide with Hf and nitridation with NH/sub 3/, sequentially, is proposed. The HfSiON gate dielectric demonstrates excellent device performances such as only 10% degradation of saturation drain current and almost 45 times of magnitude reduction in gate leakage compared with conventional SiO/sub 2/ gate at the approximately same equivalent oxide thickness. Additionally, negligible flatband voltage shift is achieved with this technique. Time-dependent dielectric breakdown tests indicate that the lifetime of HfSiON is longer than 10 years at V/sub dd/=2 V.     

The measurement of the diffusion coefficient and the sorption isotherm of water in paint films

An experimental technique together with a numerical model is proposed with which the diffusion coefficient and the sorption isotherm of water in paint can be measured. Inside a closed vessel, paint films are on stainless-steel plates. Water is present as water vapour in the air and in the paint. After blowing dry or wet air through the vessel for some time, the situation moves to a new equilibrium. The relative humidity of the air inside the vessel is measured as a function of time. From fitting the theoretical/numerical model against the experimental values, follow the diffusion coefficient and the sorption isotherm of water in the paint. The results show large scattering. When the independently measured sorption isotherm is used as an input parameter in the model, the fitting procedure gives much smaller scattering for the diffusion coefficient.     

Development of a Continuous Segmented Flow Tubular Reactor and the “Scale‐out” Concept – In Search of Perfect Powders

The synthesis of powders with controlled shape and narrow particle size distributions is still a major challenge for many industries. A continuous Segmented Flow Tubular Reactor (SFTR) has been developed to overcome homogeneity and scale‐up problems encountered when using batch reactors. Supersaturation is created by mixing the co‐reactants in a micromixer inducing precipitation; the suspension is then segmented into identical micro‐volumes by a non‐miscible fluid and sent through a tube. These micro‐volumes are more homogeneous when compared to large batch reactors leading to narrower size distributions, better particle morphology, polymorph selectivity and stoichiometry. All these features have been demonstrated on single tube SFTR for different chemical systems. To increase productivity for commercial application the SFTR is being “scaled‐out” by multiplying the number of tubes running in parallel instead of scaling‐up by increasing their size. The versatility of the multi‐tube unit will allow changes in type of precipitate with a minimum of new investment as new chemistry can be researched, developed and optimised in a single tube SFTR and then transferred to the multi‐tube unit for powder production.     

Photosensitivity of surface barrier structures based on Cu(In,Ga)Se<Subscript>2</Subscript> films grown by codeposition in vacuum

Polycrystalline Cu(In,Ga)Se₂ (CIGS) films with various ratios of Cu, In, and Ga were grown by codeposition of all elements in vacuum. The X-ray diffraction study showed that the films are single-phase and possess a chalcopyrite structure with predominant [112] orientation. The films exhibited a mirror smooth surface and had a close-packed structure composed of crystallites with clear faceting and a transverse size of 0.1–0.3 μm. Related surface barrier structures of the (In,Ag)/Cu(In,Ga)Se₂ type were obtained and their spectra of the quantum efficiency of photoconversion were studied. The obtained structures can be used for optimization of the CIGS film technology.     

The hot compaction behaviour of woven oriented polypropylene fibres and tapes. I. Mechanical properties

The aim of this work was to establish the important parameters that control the hot compaction behaviour of woven oriented polypropylene. Five commercial woven cloths, based on four different polypropylene polymers, were selected so that the perceived important variables could be studied. These include the mechanical properties of the original oriented tapes or fibres, the geometry of the oriented reinforcement (fibres or tapes), the mechanical properties of the base polymer (which are crucially dependant on the molecular weight and morphology), and the weave style. The five cloths were chosen so as to explore the boundaries of these various parameters, i.e. low and high molecular weight: circular or rectangular reinforcement (fibres or tapes): low or high tape initial orientation: coarse or fine weave.A vital aspect of this study was the realisation that hot compacted polypropylene could be envisaged as a composite, comprising an oriented ‘reinforcement’ bound together by a matrix phase, formed by melting and recrystallisation of the original oriented material. We have established the crucial importance of the properties of the melted and recrystallised matrix phase, especially the level of ductility, in controlling the properties of the hot compacted composite.