Thermal Analysis of Non-linear Convective–Radiative Hyperbolic Lumped Systems with Simultaneous Variation of Temperature-Dependent Specific Heat and Surface Emissivity by MsDTM and BPES

With the advent of temperatures near absolute zero, it is often claimed that at very low temperatures the effect of thermal wave propagation must be included by the hyperbolic heat conduction equation (HHCE). In this paper the non-linear convective–radiative HHCE is investigated. Opposite to common numerical analyses, analytical expressions are obtained for the temperature variations by the multi-step differential transformation method. Some conclusions about alteration of the specific heat of the material, temperature steeping, and Vernotte number have been formulated.     

Large-scale parallel lattice Boltzmann–cellular automaton model of two-dimensional dendritic growth

An extremely scalable lattice Boltzmann (LB)–cellular automaton (CA) model for simulations of two-dimensional (2D) dendritic solidification under forced convection is presented. The model incorporates effects of phase change, solute diffusion, melt convection, and heat transport. The LB model represents the diffusion, convection, and heat transfer phenomena. The dendrite growth is driven by a difference between actual and equilibrium liquid composition at the solid–liquid interface. The CA technique is deployed to track the new interface cells. The computer program was parallelized using the Message Passing Interface (MPI) technique. Parallel scaling of the algorithm was studied and major scalability bottlenecks were identified. Efficiency loss attributable to the high memory bandwidth requirement of the algorithm was observed when using multiple cores per processor. Parallel writing of the output variables of interest was implemented in the binary Hierarchical Data Format 5 (HDF5) to improve the output performance, and to simplify visualization. Calculations were carried out in single precision arithmetic without significant loss in accuracy, resulting in 50% reduction of memory and computational time requirements. The presented solidification model shows a very good scalability up to centimeter size domains, including more than ten million of dendrites.     

Hybrid solar parabolic dish power plant and high‐temperature phase change material energy storage system

In this study, a conventional steam power plant with two regenerative boilers is considered, and one of its boilers is replaced with parabolic solar dish collectors and storing the produced thermal energy by the phase change material (PCM) in a storage tank. The results show the necessity of the existence of an auxiliary fired‐gas boiler to provide constant load during the whole 24 hours. The performance of the proposed hybridized system is evaluated through energy and exergy analyses. It was demonstrated that substituting solar collectors with one of the boilers marginally lowers the energy efficiency but increases the exergy efficiency of the whole power plant up to 41.76%. Moreover, it is found out that this hybridization decreases the total irreversibility of the power plant in comparison with the base case, from 51.1 to 47.2 MW. The parametric analysis states that raising the mass flow rate of the heat transfer fluid in the solar collectors not only enhances the system performance but also increases the volume of the PCM tank.     

The release rate and antimicrobial activity of calcium-alginate films containing self-microemulsifying Thymus vulgaris essential oil against Escherichia coli and Staphylococcus aureus

The aim of this study was to fabricate antimicrobial calcium-alginate-based films containing the self-microemulsifying thyme essential oil (TEO) formulations using Tween 80 as the surfactant, and acetic (AA) or propionic (PA) acids as the cosurfactants. A Ca-alginate film containing nano-emulsified TEO as well as a neat Ca-alginate film were considered as the controls. The scanning electron microscopy micrographs showed a highly porous texture for SME films, which resulted in an increase in water vapor permeability and water absorption capacity of these films. The SME films released the TEO completely within 155 min and inhibited the growth of S. aureus and E. coli in in vitro antimicrobial tests. The population of S. aureus and E. coli reduced significantly in ground beef covered with SME films. The results of this study showed that self-microemulsifying TEO films could effectively increase the shelf life of ground beef by controlling its microbial population.     

Describing a strategy to estimate the CO2-heavy oil minimum miscibility pressure based on the experimental methods

To measure MMP, slim tube method is time consuming, especially for heavy oils. In this study, a strategy is considered to measure the MMP in one of the Iranian heavy oil reservoirs. The strategy steps were done through; partial data of slim tube, coupling numerical model (CNM), full slim tube, and VIT test. The results showed that CNM technique with two experimental data obtains the MMP value faster than running a full slim tube with low error result. However, VIT determined MMP faster and its results illustrated that miscibility pressure for heavy oil occurs at zero IFT, unlike light oils.     

A Short Review on Copper Calcium Titanate (CCTO) Electroceramic: Synthesis,Dielectric Properties,Film Deposition,and Sensing Application

Nano-Micro Letters - Electroceramic calcium copper titanates (CaCu3Ti4O12, CCTO), with high dielectric permittivities (ε) of approximately 105 and 104, respectively, for single crystal and...