On-line dead-time compensation method using disturbance observer

A new on-line dead-time compensation method for a permanent magnet (PM) synchronous motor drive is proposed. Using a simple disturbance observer without any additional circuit and off-line experimental measurement, disturbance voltages in the rotor reference dq frame caused by the dead time and nonideal switching characteristics of power devices are estimated in an on-line manner and fed to voltage references in order to compensate the dead-time effects. The proposed method is applied to a PM synchronous motor drive system and implemented by using software of a digital signal processor (DSP) TMS320C31. Simulations and experiments are carried out for this system and the results well demonstrate the effectiveness of the proposed method.     

A unified group technology implementation using the backpropagation learning rule of neural networks

Two engineering problems in implementing Group Technology are part family formation and part classification. Regardless of the approach adopted for the formation and classification, a critical problem is how to maintain consistency. The consistency problem can be addressed most effectively if the formation and classification is a single procedure rather than two separate procedures. A feedforward neural network using the Backpropagation learning rule is adopted to automatically generate part families during the part classification process. The spontaneous generalization capability of the neural network is utilized in classifying the parts into the families and creating new families if necessary. A heuristic algorithm using the neural network is described with an illustrative example.     

A 0.8-V accurately tuned linear continuous-time filter

An accurately tuned low-voltage linear continuous-time filter is presented in this paper. Accurate tuning is achieved using time-constant matched master-slave tuning combined with power-up mismatch calibration. A low-pass biquad designed for a corner frequency of 115 kHz achieves better than -80-dB total harmonic distortion with a 250-mV/sub pp/ 10-kHz input signal. The prototype implemented in 0.18-/spl mu/m CMOS process occupies an area of 0.4 mm/sup 2/ and dissipates 4.6 mW (2.6 mW for the filter and 2 mW for tuning) of power.     

Effect of Annealing on the Surface Microstructure of Y-Ba-Cu-O Superconducting Ceramics

Precusors to the YBa₂Cu₃O_7-δ material were prepared by both the oxalate precipitation method and conventional ceramic processing. Second-phase grains were observed to develop on the exposed fracture surface during annealing at 500° to 600°C in an ambient atmosphere. The second-phase grains were identified to be BaCO₃ using EDX and XRD. The liquid phase, which was formed because of local chemical inhomogeneity in the Y-Ba-Cu-O system, contributed to the formation of second-phase grains as a source of Ba.     

汉城旅游商务区的空间特征:以梨泰院专项旅游区为例

韩国许多城市指定了专项旅游区,通过提供若干激励政策来促进城市旅游.汉城的梨泰院1997年被指定为专项旅游区并成为CBD的一部分.本研究追溯了它作为旅游购物区的变化过程,并通过调查其土地使用找出城市空间结构的变化特征.最后,作者提出了对发展城市旅游的政策性建议,包括减少指定性区域和特殊政策.     

Preparation of aligned polyetherimide fiber by electrospinning

Fifteen to 20 wt % polyetherimide (PEI) solutions with 1-methyl-2-pyrrolidinone (NMP) were prepared. The electrical conductivity and surface tension of the solutions were determined. The fiber spinning technique of electrospinning was optimized in order to prepare unidirectionally aligned, structurally oriented nanofiber tows. The morphology of the PEI fibers was investigated using field emission scanning electron microscopy (FESEM). The well-aligned fibers with diameters between 0.58 and 0.90 μm (FESEM) were collected by electrospinning 20 wt % PEI solutions with NMP in the range of 8–10 kV onto a target rotating with a surface velocity 9.8 m/s. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008