Thermodynamic behaviour of zinc in Fe‐C and CaO‐FeO‐CaF2 slag at high temperatures

The distribution ratio of zinc between Ag‐Zn and Fe‐Zn alloys was measured to clarify the thermodynamic behaviour of zinc in Fe‐C melt at high temperatures. Also, the distribution ratio between Ag‐Zn alloy and CaO‐FeO‐CaF₂ slag was measured to understand the dissolution mechanism of zinc in molten slags. The activity coefficient of zinc in Ag‐Zn alloy was preliminarily measured as a fundamental thermodynamic data for the activity of zinc in Fe‐C melt. From the dependence of the activity coefficient of zinc in Fe‐C melts on temperature and carbon content, the following equation could be obtained at 1473 ‐ 1623 K: The distribution ratio of zinc between Ag‐Zn alloy and CaO‐FeO‐CaF₂ slag increased by increasing both the oxygen potential and slag basicity. The stoichiometric coefficients of the dissolution reaction were obtained by considering the relationship between zinc distribution ratio and slag basicity or oxygen partial pressure, when one of these two independent variables was fixed. The dissolution reaction of zinc into the slags could be described as follows:      

LED‐backlight feedback control system with integrated amorphous‐silicon color sensor on an LCD panel

Abstract— Thin‐film‐transistor liquid‐crystal displays (TFT‐LCDs) have the largest market share of all digital flat‐panel displays. An LCD backlighting system employing a three‐color red‐green‐blue light‐emitting diode (RGB‐LED) array is very attractive, considering its wide color gamut, tunable white point, high dimming ratio, long lifetime, and environmental compatibility. But the high‐intensity LED has problems with thermal stability and degradation of brightness over time. Color and white luminance levels are not stable over a wide range of temperature due to inherent long‐term aging characteristics. In order to minimize color point and brightness differences over time, optical feedback control is the key technology for any LED‐backlight system. In this paper, the feasibility of an optical color‐sensing feedback system for an LED backlight by integrating the amorphous‐silicon (a‐Si) color sensor onto the LCD panel will be presented. To minimize the photoconductivity degradation of a‐Si, a new laser exposure treatment has been applied. The integrated color‐sensor optical‐feedback‐controlled LED‐backlight system minimized the color variation to less than 0.008 Δu'v' (CIE1976) compared to 0.025 for an open‐loop system over the temperature range of 42–76°C.     

Practical crack control during the construction of precast segmental box girder bridges

Cracks that occurred in the bottom slab of a precast segmental bridge were investigated through a construction sequence analysis, which revealed that the cracks were caused by excessive deformation during temporary post-tensioning while joining the segments. In addition, a parametric study was performed to evaluate the effects of the prestressing sequence, bottom slab thickness, and position of the prestressing anchors. The structural behavior of the girder sections was greatly affected by the thickness of the bottom slab and the position of prestressing anchors, but not by the prestressing sequence. Based on the results, a construction method that prevents the cracks is proposed.     

Lightweight monitors for the Java virtual machine

Java supports the monitor construct for language‐level synchronization in the context of multi‐threading. This paper introduces the lightweight monitor, an efficient user‐level monitor implementation. The lightweight monitor is useful for single‐threaded Java programs as well as for multi‐threaded Java programs with little lock contention. A 32‐bit lock is embedded in each object for efficient lock access while other monitor data structures are managed using a hash table. We highly optimized the lock manipulation code, which is translated and inlined by a just‐in‐time (JIT) compiler. In the most probable cases, only nine SPARC instructions are spent for lock acquisition and five instructions are spent for lock release. Our experimental results indicate that the lightweight monitor is faster than the monitor implementation in the SUN JDK 1.2 RC1 by up to 21 times in the absence of lock contention and by up to seven times in the presence of lock contention. Copyright © 2004 John Wiley & Sons, Ltd.     

Organic thin‐film devices on paper substrates

Abstract— A high‐performance polymer thin‐film transistor fabricated on a paper substrate has been demonstrated. As a water barrier layer, parylene was coated on a paper substrate by using a vacuum deposition process. Using poly (3‐hexylthiophene) as an active layer, a polymer thin‐film transistor with a field‐effect mobility of up to 0.086 cm²/V‐sec and an on/off ratio of 10⁴ was achieved. The fabrication of a polymer thin‐film transistor built on an inexpensive paper substrate is expected to open a channel for future applications in flexible and disposable electronics with extremely low cost.     

Interfacial reaction between 42Sn-58Bi solder and electroless Ni-P/immersion Au under bump metallurgy during aging

The interfacial reaction between 42Sn-58Bi solder (in wt.% unless specified otherwise) and electroless Ni-P/immersion Au was investigated before and after thermal aging, with a focus on the formation and growth of an intermetallic compound layer, consumption of under bump metallurgy (UBM), and bump shear strength. The immersion Au layer with thicknesses of 0 μm (bare Ni), 0.1 μm, and 1 μm was plated on a 5-μm-thick layer of electroless Ni-P (with 14–15 at.% P). The 42Sn-58Bi solder balls were then fabricated on three different UBM structures by using screen printing and pre-reflow. A Ni₃Sn₄ layer formed at the joint interface after the pre-reflow for all three UBM structures. On aging at 125°C, a quaternary phase, identified as Sn₇₇Ni₁₅Bi₆Au₂, was observed above the Ni₃Sn₄ layer in the UBM structures that contain Au. The thick Sn₇₇Ni₁₅Bi₆Au₂ layer degraded the integrity of the solder joint, and the shear strength of the solder bump was about 40% less than the nonaged joints.     

Wavelet-based low-delay ECG compression algorithm for continuous ECG transmission.

The delay performance of compression algorithms is particularly important when time-critical data transmission is required. In this paper, we propose a wavelet-based electrocardiogram (ECG) compression algorithm with a low delay property for instantaneous, continuous ECG transmission suitable for telecardiology applications over a wireless network. The proposed algorithm reduces the frame size as much as possible to achieve a low delay, while maintaining reconstructed signal quality. To attain both low delay and high quality, it employs waveform partitioning, adaptive frame size adjustment, wavelet compression, flexible bit allocation, and header compression. The performances of the proposed algorithm in terms of reconstructed signal quality, processing delay, and error resilience were evaluated using the Massachusetts Institute of Technology University and Beth Israel Hospital (MIT-BIH) and Creighton University Ventricular Tachyarrhythmia (CU) databases and a code division multiple access-based simulation model with mobile channel noise.     

An integrated model for the design of end-of-aisle order picking system and the determination of unit load sizes of AGVs

In this paper, we deal with an assembly line production system in which an automated guided vehicle (AGV) delivers parts to each workstation of assembly lines from a miniload automated storage/retrieval system (AS/RS). Each assembly production line is characterized by a sequence of workstations linked together for the production of a given type of product. We consider simultaneously the design problem of miniload AS/RS and the problem of determining a unit load size of the AGV. First, a non-linear mathematical model is formulated under a proposed AGV dispatching policy. And then, we determine an appropriate sequence of lines of the vehicle visits. Finally, based on the characteristics of the objective function and feasible region of the decision variables, a heuristic solution procedure is developed to find a near optimal solution. To examine the validity of the model, an example problem is solved.     

An application of polarized domains in ferroelectric thin films using scanning probe microscope

The feasibility of utilizing PZT films as future data storage media was investigated using a modified AFM. Applying voltages between a conductive AFM tip and the PZT films causes the switching of ferroelectric domains. The domains are observed using an EFM imaging technique. The experimental results and calculations revealed that the electrostatic force generated between the polarized area and the tip is a main contributor for the imaging of the polarized domains. The written features on ferroelectric films were less than 100 nm in diameter, implying the possibility of realizing data storage devices with ultra-high area density. The disappearance of the polarized images without any applied voltage was observed, which is a drawback in this application of PZT thin films.