Push-pull quantum series resonant rectifier without start-up inrushcurrent

A new combined buck and boost push-pull quantum series resonant rectifier (PPQSRR) is proposed to achieve a power factor correction without start-up inrush current. With the proposed control method and circuitry, a high power factor and wide range of output voltage without an inrush current can be obtained     

Covalently cross-linked sulfonated poly(ether ether ketone)/tungstophosphoric acid composite membranes for water electrolysis application

Composite polymer electrolyte membranes consisting of covalently cross-linked sulfonated polyether ether ketone (SPEEK) with tungstophosphoric acid (TPA) are prepared and their electrochemical and mechanical properties are investigated with regards to application in water electrolysis. Covalently cross-linked membranes (CL-SPEEK) comprised of sulfochlorinated SPEEK membranes and SPEEK partially lithiated by LiCl, are prepared by reaction with 1,4-diiodobutane, and blended with TPA to avoid excessive water swelling and to reinforce their mechanical properties. These ion-exchange membranes show good electrochemical properties, including proton conductivity, ion exchange capacity (IEC), thermal stability, anti-oxidative stability, and satisfactory mechanical characteristics, such as tensile strength and elongation. In particular, among the TPA-composite membranes, the CL-SPEEK/TPA30 (30 wt.% TPA) membrane displays higher proton conductivity (0.128 S cm⁻¹) and tensile strength (75.01 MPa) than Nafion^® 117 at 80 °C. The ion-exchange membranes are used to construct membrane electrode assemblies (MEAs) of use in polymer electrolyte membrane electrolysis (PEME). The MEA are prepared using a non-equilibrium impregnation–reduction (I–R) method. The electrochemical surface area (ESA) and roughness factor of the MEA prepared with CL-SPEEK/TPA30 electrolyte measured by cyclic voltammetry are 25.11 m² g⁻¹ and 321.4 cm² Pt cm⁻², respectively. The prepared MEAs are used in the water-electrolysis unit cells. The cell voltage is 1.78 V at 1 A cm⁻² and 80 °C, with a platinum loading of 1.28 mg cm⁻². The results of the present study suggest that the good conductivity and mechanical properties of covalently CL-SPEEK/TPA composite membranes make them well suited for use in PEME.     

Spatially adaptive high-resolution image reconstruction of DCT-based compressed images

The problem of recovering a high-resolution image from a sequence of low-resolution DCT-based compressed observations is considered in this paper. The introduction of compression complicates the recovery problem. We analyze the DCT quantization noise and propose to model it in the spatial domain as a colored Gaussian process. This allows us to estimate the quantization noise at low bit-rates without explicit knowledge of the original image frame, and we propose a method that simultaneously estimates the quantization noise along with the high-resolution data. We also incorporate a nonstationary image prior model to address blocking and ringing artifacts while still preserving edges. To facilitate the simultaneous estimate, we employ a regularization functional to determine the regularization parameter without any prior knowledge of the reconstruction procedure. The smoothing functional to be minimized is then formulated to have a global minimizer in spite of its nonlinearity by enforcing convergence and convexity requirements. Experiments illustrate the benefit of the proposed method when compared to traditional high-resolution image reconstruction methods. Quantitative and qualitative comparisons are provided.     

New Syndrome Check Error Estimation and Its Concatenated Coding

A low-complexity and high performance SCEE (Syndrome Check Error Estimation) decoding method for convolutional codes and its concatenated SCEE/RS (Reed–Solomon) coding scheme are proposed. First, we describe the operation of the decoding steps in the proposed algorithm. Then deterministic values on the decoding operation are derived when some combination of predecoder-reencoder is used. Computer simulation results show that the computational complexity of the proposed SCEE decoder is significantly reduced compared to that of conventional Viterbi decoder without degradation of the P_e performance. Also, simulation results of BER performance of the concatenated SCEE/Hard Decision Viterbi (HD-Viterbi) and SCEE/RS (Reed–Solomon) codes are presented.     

Wide‐Band Fine‐Resolution DCO with an Active Inductor and Three‐Step Coarse Tuning Loop

This paper presents a wide‐band fine‐resolution digitally controlled oscillator (DCO) with an active inductor using an automatic three‐step coarse and gain tuning loop. To control the frequency of the DCO, the transconductance of the active inductor is tuned digitally. To cover the wide tuning range, a three‐step coarse tuning scheme is used. In addition, the DCO gain needs to be calibrated digitally to compensate for gain variations. The DCO tuning range is 58% at 2.4 GHz, and the power consumption is 6.6 mW from a 1.2 V supply voltage. An effective frequency resolution is 0.14 kHz. The phase noise of the DCO output at 2.4 GHz is –120.67 dBc/Hz at 1 MHz offset.     

Thermally Controlled,Patterned Graphene Transfer Printing for Transparent and Wearable Electronic/Optoelectronic System

Graphene has been highlighted as a platform material in transparent electronics and optoelectronics, including flexible and stretchable ones, due to its unique properties such as optical transparency, mechanical softness, ultrathin thickness, and high carrier mobility. Despite huge research efforts for graphene‐based electronic/optoelectronic devices, there are remaining challenges in terms of their seamless integration, such as the high‐quality contact formation, precise alignment of micrometer‐scale patterns, and control of interfacial‐adhesion/local‐resistance. Here, a thermally controlled transfer printing technique that allows multiple patterned‐graphene transfers at desired locations is presented. Using the thermal‐expansion mismatch between the viscoelastic sacrificial layer and the elastic stamp, a “heating and cooling” process precisely positions patterned graphene layers on various substrates, including graphene prepatterns, hydrophilic surfaces, and superhydrophobic surfaces, with high transfer yields. A detailed theoretical analysis of underlying physics/mechanics of this approach is also described. The proposed transfer printing successfully integrates graphene‐based stretchable sensors, actuators, light‐emitting diodes, and other electronics in one platform, paving the way toward transparent and wearable multifunctional electronic systems.     

A WDM-PON Employing Fabry–PÉrot Laser Diodes Without a Seed Light Injection

We propose and demonstrate a wavelength-division-multiplexed passive optical network by employing double-contact Fabry-Perot laser diodes (F-P LDs) without a seed light injection. To avoid the high mode partition noise at low frequency, we use a binary phase-shift keying as a modulation format at a low relative intensity noise window. An error-free transmission is achieved by compensating a lasing envelope shift due to temperature variation with the double-contact F-P LD.     

High Performance Three‐Dimensional Chemical Sensor Platform Using Reduced Graphene Oxide Formed on High Aspect‐Ratio Micro‐Pillars

The sensing performance of chemical sensors can be achieved not only by modification or hybridization of sensing materials but also through new design in device geometry. The performance of a chemical sensing device can be enhenced from a simple three‐dimensional (3D) chemiresistor‐based gas sensor platform with an increased surface area by forming networked, self‐assembled reduced graphene oxide (R‐GO) nanosheets on 3D SU8 micro‐pillar arrays. The 3D R‐GO sensor is highly responsive to low concentration of ammonia (NH₃) and nitrogen dioxide (NO₂) diluted in dry air at room temperature. Compared to the two‐dimensional planar R‐GO sensor structure, as the result of the increase in sensing area and interaction cross‐section of R‐GO on the same device area, the 3D R‐GO gas sensors show improved sensing performance with faster response (about 2%/s exposure), higher sensitivity, and even a possibly lower limit of detection towards NH₃ at room temperature.     

Direct Transfer Printing with Metal Oxide Layers for Fabricating Flexible Nanowire Devices

A direct printing method for fabricating devices by using metal oxide transfer layers instead of conventional transfer media such as polydimethylsiloxane is presented. Metal oxides are not damaged by organic solvents; therefore, electrodes with gaps less than 2 μm can be defined on a metal oxide transfer layer through photolithography. In order to determine a suitable metal oxide for use as transfer layer, the surface energies of various metal oxides are measured, and Au layers deposited on these oxides are transferred onto polyvinylphenol (PVP). To verify the feasibility of our approach, Au source–drain electrodes on transfer layers and Si nanowires (NWs) addressed by the dielectrophoretic (DEP) alignment process are transferred onto rigid and flexible PVP‐coated substrates. Based on transfer test and DEP process, Al₂O₃ is determined to be the best transfer layer. Finally, Si NWs field effect transistors (FETs) are fabricated on a rigid Si substrate and a flexible polyimide film. As the channel length decreases from 3.442 to 1.767 μm, the mobility of FET on the Si substrate increases from 127.61 ± 37.64 to 181.60 ± 23.73 cm² V^?1 s^?1. Furthermore, the flexible Si NWs FETs fabricated through this process show enhanced electrical properties with an increasing number of bending cycles.