Thermally reused solar energy harvesting using current mirror cells

This paper implements a simultaneous solar and thermal energy harvesting system, as a hybrid energy harvesting (HEH) system, to convert ambient light into electrical energy through photovoltaic (PV) cells and heat absorbed in the body of PV cells. Indeed, a solar panel equipped with serially connected thermoelectric generators not only converts the incoming light into electricity but also takes advantage of heat emanating from the light. In a conventional HEH system, the diode block is used to provide the path for the input source with the highest value. In this scheme, at each time, only one source can be handled to generate its output, while other sources are blocked. To handle this challenge of combining resources in HEH systems, this paper proposes a method for collecting all incoming energies and conveying its summation to the load via the current mirror cells in an approach similar to the maximum power point tracking. This technique is implemented using off-the-shelf components. The measurement results show that the proposed method is a realistic approach for supplying electrical energy to wireless sensor nodes and low-power electronics.     

Verformungsverhalten nanostrukturierter HPPMS‐Hartstoffschichten

Elastic‐Plastic Deformation Behavior of Nanostructured HPPMS Hard Coatings Nitride hard coatings deposited via HPPMS (High Power Pulsed Magnetron Sputtering) or HiPIMS (High Power Impulse Magnetron Sputtering) are widely used in tribological applications due to their promising wear and corrosion resistance. During the application, the coated tools or components may be exposed to significant mechanical loads. Therefore, investigations on deformation behavior of the coatings under mechanical loading are of great importance. The objective of the present study was a comprehensive investigation on deformation behavior of nitride hard coatings from the coating system M‐Al‐O‐N (M = Cr, V) using nanoindentation und nanoscratch tests. In this regard, both nanoscale multilayer (nanolaminate) and monolayer coatings were investigated. All the coatings were deposited using HPPMS technology. Contrary to the expectations regarding a brittle behavior of ceramic‐like coatings, the results depict a considerable plastic deformation of the investigated hard coatings. Furthermore, in addition to a high strength, the applied coatings show a high crack resistance under mechanical loading.     

Thermo-mechanical vibration analysis of rotating nonlocal nanoplates applying generalized differential quadrature method

In this study, thermal and small-scale effects on the flapwise bending vibrations of a rotating nanoplate, which can be the basis of nano-turbine design, have been analyzed. The nano-turbine is made of an orthotropic nanoplate with a setting angle that is modeled based on the classical plate theory (CPT) with cantilever boundary conditions. The axial forces are also included in the model as the true spatial variation due to the rotation and temperature change. The governing equations and boundary conditions are derived according to Hamilton's principle and the governing equations are solved with the aid of the generalized differential quadrature method. The effects of small-scale parameter, nondimensional angular velocity, temperature change, and setting angles in the first four nondimensional frequencies are discussed. Due to the consideration of the rotating effects, results of this study are applicable in nano-machines, such as nano-motors, nano-rotor, and other rotating nano-structures. Also, by considering the effect of thermal loading on rotation of a nanoplate, the results are useful in the design of nano-turbines.     

Optical-fibre network system for air-pollution monitoring over a wide area by optical absorption method

A low-loss optical-fibre network system for monitoring air pollution and species concentrations in various environments utilising the differential absorption method is proposed and discussed as a sensitive and economical as well as nonhazardous method. Its feasibility and advantages are also described on the basis of the present state of the art of the relevant technology.     

Synthesis,characterization and comparison of polythiophene–carbon nanocomposite materials as Pt electrocatalyst supports for fuel cell applications

A novel polymer–carbon (PTh–C) nanocomposites containing different percentages of polythiophene (10, 20 and 50% (w/w)) and carbon (Vulcan XC-72) was prepared by a facile solution dispersion method and used to support platinum nanoparticles. The effect of using different percentages of polythiophene in nanocomposites and subsequently prepared electrocatalysts was investigated. The resultant electrocatalysts were extensively characterized by physical (X-ray diffraction (XRD) and transmission electron microscopy (TEM)) and electrochemical (cyclic voltammetry (CV)) techniques. The TEM results showed that the fine Pt nanoparticles prepared by ethylene glycol (EG) method were distributed on the surface of the 50% PTh–C nanocomposites successfully. From the XRD patterns, the average size of dispersed Pt nanoparticles with the face-centered cubic (fcc) structure on 50% PTh–C, 20% PTh–C, 10% PTh–C and carbon were about 4.9, 5.2, 5.4 and 6.1 nm, respectively. The conductivity of PTh–C with different percentages of pure PTh was compared with the conductivity of the corresponding support of pure PTh. It is observed that the conductivity of 50% PTh–C nanocomposites is about 600 times higher than that of pure PTh. Finally, CV measurements of hydrogen and methanol oxidations indicated that Pt/50% PTh–C had a higher electrochemical surface area and higher catalytic activity for methanol oxidation reaction compared to other electrocatalysts. These measurements showed that the Pt/50% PTh–C electrocatalyst by the value of 3.85 had higher \(I_{\mathrm{f}}/I_{\mathrm{b}}\) ratio with respect to Pt/10% PTh–C and Pt/20% PTh–C by the values of 2.66 and 2.0, respectively.     

In situ synthesis of hydroxyapatite-grafted titanium nanotube composite

ABSTRACT

The present study is an investigation to demonstrate the effectiveness of in situ approach in the synthesis of hydroxyapatite-grafted titanium nanotube composite (HA-TNT). This method involves combining the process of HA sol–gel and rapid breakdown anodisation of titanium in a novel solution consisting of NaCl and N₃PO₄. This new synthesis approach produced a uniform dispersion of Anatase and Rutile phases of TiO₂ nanotubes with minimal agglomeration in the matrix of crystalline HA. The characterisation of homogenised HA-TNT composite was investigated via field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), transmission electron microscope (TEM) and X-ray diffraction (XRD). FESEM and TEM images indicated the nanostructure of composite with TiO₂ nanotube diameter of approximately 10 nm. XRD and EDS analyses confirmed the formation of HA crystalline with the Ca/P ratio of 1.58 and formation of Anatase and Rutile phase of TiO₂ nanotubes.     

Self-standing crystalline TiO2 nanotubes/CNTs heterojunction membrane: synthesis and characterization

In the present study, we report for the first time synthesis of TiO(2) nanotubes/CNTs heterojunction membrane. Chemical vapor deposition (CVD) of CNTs at 650 °C in a mixture of H(2)/He atmosphere led to in situ detachment of the anodically fabricated TiO(2) nanotube layers from the Ti substrate underneath. Morphological and structural evolution of TiO(2) nanotubes after CNTs deposition were investigated by field- emission scanning electron microscopy (FESEM), glancing angle X-ray diffraction (GAXRD), and X-ray photoelectron spectroscopy (XPS) analyses.     

Prediction of Acid Mine Drainage: Importance of Mineralogy and the Test Protocols for Static and Kinetic Tests

Static tests, which compare the acid-generating potential and acid-neutralizing potential for a given mine waste (tailings or waste rocks), are characterized by a wide uncertainty zone in which it is impossible to accurately predict the acid-generating potential (AGP). Then, to better assess long-term AGP, kinetic tests are usually performed to provide more information about the reaction rates of the acid-generating and acid-neutralizing minerals. The present work compares the classic Sobek static test with three mineralogical static tests to assess the importance of sample mineralogy in acid mine drainage (AMD) prediction. We also investigated how experimental procedures related to static tests can influence prediction results. We used three synthetic tailings samples made by mixing well-characterized pure minerals in calibrated proportions. Although basically different in their principles and procedures, the modified Sobek and mineralogical static tests gave similar results. These AGP predictions were then validated by the use of a kinetic test. The kinetic test protocol was also modified in this study and the results obtained correlated well with the static test results, in contrast to the standard kinetic test protocol. The present work highlights the limitations of static and kinetic test procedures, and provides recommendations for a better use of these tests for more reliable AMD prediction.     

Radioactivity calculations for production of <Superscript>131</Superscript>I by neutron irradiation of tellurium targets

The radioactivity of ¹³¹I as well as of the other radioisotopes, obtained from different nuclear reactions occurring during irradiation of natural tellurium including different decay branches, at the end of irradiation and after different cooling times was calculated. The optimum cooling time is 90 h. Published in Russian in Radiokhimiya, 2009, Vol. 51, No. 3, pp. 275–281. The text was submitted by the author in English.