Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

光纤光栅感温火灾探测报警系统在原油罐区的应用

通过对现有罐区火灾自动报警技术的认真考察、对比,在石西集中处理站原油罐区安装了光纤光栅感温火灾探测报警系统.该报警系统的传感信号是光的波长变化,传感器及其探测系统是靠光缆连接而进入被测现场,它具有高安全性、高可靠性、高绝缘性、高抗电磁干扰性、防潮耐蚀、寿命长等其他传统火灾探测报警系统无法比拟的优越性能.阐述了其系统构成和运行效果.该系统在石西集中处理站运用效果良好.     

A级道路石油沥青的开发与生产

通过对道路石油沥青针入度指数(PI)与平均分子量关系的研究,提出了选择原油、提高减压蒸馏分离效果、氧化和原油混合提高道路石油沥青PI的方法,筛选原油得出进口原油2可生产A级产品,氧化试验证明选择合适的氧化条件沙中减渣可制备A级产品,减压蒸馏试验并经工业装置验证得出沙中原油可生产A级产品。     

对海水进行混凝除浊预处理研究

介绍采用聚合氯化铁（PFC）为絮凝剂，对海水进行混凝除浊预处理方法。考察了原海水pH、搅拌速度、反应时间及PFC用量对海水预处理效果的影响。结果表明，在原海水pH凋至9．0，搅拌速度控制在200min^-1，反应时间选择8—10min，PFC用量0．10μg／g的最佳条件下，能使处理后的海水浊度降至0．05mol／L，而联产的酸性废水中和剂浆料中Mg（OH）2含量在25％～45％，大肠菌群的去除率大于89．3％。     

循环流化床固-固换热系统传热规律

在自制的循环流化床固-固换热设备中,以催化裂化平衡催化剂[平均粒径60μm,堆密度980 kg/m3,比热1.01 kJ/(kg.K),临界流化速度0.002 1 m/s]为原料,对系统的循环特性及传热规律进行了研究,考察了床层密度、提升风量、床层温度、催化剂粒径等因素对传热的影响。结果表明,随着提升风量增加,表观气速增大,床层密度下降,传热系数下降;提高床层温度,减小催化剂的粒径,传热系数增加。     

贴片机脱机编程的快捷方法

SMT生产线中的大多数加工设备均为数控设备。它们编程所需要的大多数特征数据均可从CAD设计系统中得到。文章介绍了如何从CAD设计系统中导出X、Y坐标数据,并转换成贴片数据的方法和思路,以期引起更多的同行加入到这方面的研究中。     

工作流技术及其应用研究

文章介绍了工作流技术及其发展历史,对工作流的系统模型进行了详细分析,探讨了工作流技术在企业管理信息系统中的实际应用。     

基于"层"模式的双机容错系统

容错技术广泛应用于各个行业来保证系统的冗余和可靠性。文章在分析比较当前的双机容错系统的性能优缺点后,提出了一种全新的基于“层”模式的双机容错系统解决方案。按照这种模式,可以从链路层到应用层构建一个通用的系统级的双机容错系统。文章对其实现的关键技术进行了阐述。