A distributed laxity-based priority scheduling scheme for time-sensitive traffic in mobile ad hoc networks

Characteristics of Mobile Ad hoc Networks such as shared broadcast channel, bandwidth and battery power limitations, highly dynamic topology, and location dependent errors, make provisioning of quality of service (QoS) in such networks very difficult. The Medium Access Control (MAC) layer plays a very important role as far as QoS is concerned. The MAC layer is responsible for selecting the next packet to be transmitted and the timing of its transmission. We have proposed a new MAC layer protocol that includes a laxity-based priority scheduling scheme and an associated back-off scheme, for supporting time-sensitive traffic. In the proposed scheduling scheme, we select the next packet to be transmitted, based on its priority value which takes into consideration the uniform laxity budget of the packet, the current packet delivery ratio of the flow to which the packet belongs, and the packet delivery ratio desired by the user. The back-off mechanism devised by us grants a node access to the channel, based on the rank of its highest priority packet in comparison to other such packets queued at nodes in the neighborhood of the current node. We have studied the performance of our protocol that combines a packet scheduling scheme and a channel access scheme through simulation experiments, and the simulation results show that our protocol exhibits a significant improvement in packet delivery ratio under bounded end-to-end delay requirements, compared to the existing 802.11 DCF and the Distributed Priority Scheduling scheme proposed recently in [ACM Wireless Networks Journal 8 (5) (2002) 455–466; Proceedings of ACM MOBICOM '01, July 2001, pp. 200–209].     

Mathematical modeling of mixing phenomena in a gas stirred liquid bath

A macroscopic, steady state energy balance model has been formulated to describe mixing phenom-ena in a liquid bath stirred by injecting gas through a straight nozzle fitted axially at the bottom of the vessel. This, along with experimental data on a water model previously reported, was employed to make predictions. Input energy terms considered in the model consist of buoyancy energy and empirically determined fraction of gas kinetic energy. Dissipation of energy was attributed to liquid circulation and bubble slip. The two-phase plume was assumed to be a truncated cone whose dimen-sions depended upon operating conditions. Numerical solution of model equations gave liquid velocity and gas hold-up inside the plume as well as liquid circulation rate and liquid velocity in the region outside the plume. Influence of process variables, e.g., gas flow rate, bath height, and nozzle diameter, have been predicted. Validity of the model has been established by comparing some pre-dicted entrainment ratios with those experimentally measured by other investigators. Empirical cor-relations to predict circulation time and circulation number have been proposed. Circulation number was found to vary between 2 and 12 in contrast to the existing assumption in the literature of a con-stant value of 3. Usefulness of these correlations in predicting mixing time for industrial vessels has been demonstrated. Formerly a Graduate Student in the De-partment of Metallurgical Engineering at the Indian Institute of Technol-ogy, Kanpur     

Prediction of the freezing characteristics of spherical-shaped food productsPrévision des caractéristiques de congélation des aliments de forme sphérique

An analysis of the freezing characteristics of spherical shaped food products with time dependent surface-temperature variation is presented. The one dimensional heat conduction equations in spherical coordinates for the frozen and unfrozen regions are solved simultaneously by a suitable transformation to obtain an equivalent slab. Goodman's integral method is applied to obtain the solution in terms of four dimensionless parameters. The results are presented for an exponential variation of the surface temperature for parameter values covering the ranges of the thermophysical properties and processing conditions encountered in food freezing practice. A correlation for facilitating the estimation of the freezing time is also given.     

Energy-efficient directional routing between partitioned actors in wireless sensor and actor networks

Actor?actor communication is an important part of the functioning of wireless sensor?actor networks and enables the actor nodes to take coordinated action on a given event. Owing to various reasons such as actor mobility and low actor density, the actor network tends to get partitioned. The authors propose to use the underlying sensor nodes, which are more densely deployed, to heal these partitions. In order to maximise the utilisation of the limited energy available with the sensor nodes, a new routing protocol for actor?actor communication using directional antennas on the actor nodes is proposed. The authors contribution is threefold. First, using simulations they show that the problem of partitioning in the actor networks is significant and propose an architecture with directional antennas on actor nodes and sensor bridges to heal these partitions. Second, they identify the routing problem for this architecture based on a theoretical framework and propose centralised as well as distributed solutions to it. Third, they develop a routing protocol based on the distributed solution and show, using network simulations, that the proposed protocol not only heals the network partitions successfully, but also achieves high throughput and fairness across different flows, in addition to maximising the network lifetime.     

The effects of data model representation method on task performance

Data models are frequently created with little thought about their layout. Our research examined how data models organized in a columnar fashion compared to equivalent data models which did not, by improving novice designer's performance in error detection, comprehension, and query construction.     

Microwave Hydrothermally Synthesized Nanocrystalline Co-Zn Ferrites

Co-Zn ferrite nano-powder was synthesized using the Microwave- Hydrothermal (M-H) method. The powder was characterized using X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), and Fourier Transform Infrared spectroscopy (FT-IR). The densification of nanoferrites was done using two methods: a) conventional and b) microwave sintering. Electrical and magnetic properties of the sintered samples were measured at room temperature. Electrical properties such as dielectric constant (?'), dissipation factor (D), initial permeability (μ_i) and quality factor (Q) were measured over a wide frequency range (10 kHz to 1 MHz). The Curie temperature has been determined from the permeability versus temperature plots. It was found that the enhanced electrical and magnetic properties were observed for microwave sintered samples.     

Microwave-Hydrothermal Synthesis of Ni0.53Cu0.12Zn0.35Fe2O4/SiO2 Nanocomposites for MLCI

The nanocomposites of NiCuZnFe₂O₄-SiO₂ were prepared using Microwave-Hydrothermal method at 160°C/45 min.The as-synthesized powders were characterized using X-ray diffraction and Transmission Electron Microscope (TEM).The average particle size of the powders were found to be ～20 nm.The powders were densified at 900°C/30 min using Microwave sintering method. The sintered composite samples were characterized using XRD and Scanning Electron Microscopy (SEM). Crystallite size of the ferrites decreases with an increase of SiO₂ content. The density of the composites varies of 93–98% of theoretical density. The densities of the present composites were increasing with the addition of SiO_2. The bulk densities of the present composites were increasing with the addition of SiO₂. The structural changes in these samples were characterized using Fourier Transform Infrared Spectrometer (FTIR) in the 400–4000 cm^?1. The bands in the range of 580–880 cm^?1 show a slight increase in intensity, which could be ascribed to the enhanced interactions between the NiCuZnFe₂O₄ clusters and silica matrix. The resistivity of the sintered samples was increased with an addition of ferrite content. The real and imaginary parts of permittivity and permeability were measured in the frequency range of 1 MHz–1.8 GHz.The addition of SiO₂ alters the values of dielectric constant and permeability which is useful to the Multilayer Chip Inductors (MLCI) fabrication.     

Influence of copper substitution on magnetic and electrical properties of MgCuZn ferrite prepared by microwave sintering method

Polycrystalline MgCuZn ferrites with chemical formula Mg_0.50-xCu_xZn_0.50Fe₂O₄ (x = 0.00, 0.05, 0.10, 0.15, 0.20, 0.25 and 0.30) were prepared by microwave sintering method. These powders were calcined, compacted and sintered at 950 °C for 30 min. Structural, microstructural and elemental analyses were carried out using X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometry (EDS), respectively. The lattice parameter is found to increase with increasing copper content. A remarkable densification is observed with the addition of Cu ions in the ferrites. The sintered ferrite was characterized for initial permeability, dielectric constant and dielectric loss tangent and ac conductivity measurements. The temperature variation of the initial permeability of these samples was carried out from 30 °C to 200 °C. The dielectric constant, dielectric loss tangent and ac conductivity have been measured in the frequency range of 100 Hz to 1 MHz. Initial permeability and dielectric constant were found to increase and dielectric loss decreased with Cu substitution for Mg, up to x = 0.20. The ferrite powder prepared is suitable for the application in multilayer chip inductor due to its low-temperature sinterability, good magnetic properties and low loss at high frequency.     

Numerical Simulation of the Head/Disk Interface for Patterned Media

The use of patterned media is a new approach proposed to extend the recording densities of hard disk drives beyond 1 Tb/in.². Bit-patterned media (BPM) overcome the thermal stability problems of conventional media by using single-domain islands for each bit of recorded information, thereby eliminating the magnetic transition noise (Albrecht et al., Magnetic Recording on Patterned Media, 2003). Considering steady state conditions, we have transferred the pattern from the disk surface onto the slider surface and have investigated the pressure generation due to the bit pattern. To reduce the numerical complexity, we have generated the bit pattern only in the areas of the slider near the trailing edge, where the spacing is small. Cylindrical protrusions were modeled using very small mesh size on the order of nanometers to obtain the flying characteristics for the entire slider air bearing surface (ABS) using the “CMRR” finite element Reynolds equation simulator (Duwensee et al., Microsyst Technol, 2006; Wahl et al., STLE Tribol Trans, 39(1), 1996). The effect of pattern height, pattern diameter, slider skew angle, and slider pitch angle on flying height of a typical slider is investigated. Numerical results show that the flying height decreases for a patterned slider and the change in flying height is a function of the pattern height and ratio of the pattern diameter to the pattern pitch. In comparison to discrete track media, the flying height loss is larger for a patterned slider disk interface for the same recessed area of pattern.