Polymerization of isoprene in n-heptane with triethylaluminum–titanium tetrachloride catalyst. I. Effect of Al/Ti ratio on stereoregularity,conversion, molecular weight,and molecular weight distribution

The influence of the Al/Ti ratio of the heterogeneous Ziegler–Natta catalyst system AlEt₃–TiCl₄ on the isoprene polymerization in n-heptane at 30°C in a bench scale reactor was investigated. Each batch run consisted of 50 mL isoprene, 200 mL n-heptane with 0.45 and 0.5g catalyst. Conversion of isoprene and molecular weights of polyisoprene increased with increasing Al/Ti ratio, reaching their maxima values at 1.0 and 1.2, respectively. Conversion and molecular weights decreased remarkably at a higher ratio of Al/Ti. As this ratio decreases from the value of 1.2 to 0.4, the cis1,4 content in polyisoprene decreased from 97 to 25%. When the ratio of Al/Ti increased from 1.2 to 2.2 the cis-1,4 structure of polyisoprene decreased from 97 to 85%.     

Quantitative preparation of long chain thioethers from an oxo-trans-2-enoic ester and a 9,12-dioxo-trans-10-enoic acid

Branched-chain thioethers have been prepared from methyl 4-oxo-trans-2-hexadecenoate and 9,12-dioxo-trans-10-octadecenoic acid. The reagents involved in these preparations were mercaptoacetic and mercaptopropionic acids. The yields of these thioethers are almost quantitative.     

Role of sand on curing of partex surface by UV radiation

A partex surface was modified by a UV‐curing system with epoxy acrylate (EB‐600). A set of formulations was prepared with oligomer and the trifunctional monomer trimethylol propane triacrylate in different combinations of percentages (1–5%) of sand to study the role of sand in various physical properties of UV‐cured thin films, as well as partex surfaces. Increased pendulum hardness (PH), gloss, adhesion, and abrasion values were obtained by the addition of sand into the partex surfaces. The best results were obtained with the formulation containing 3% sand. An enhanced PH and a decreased percentage of gel content of the UV‐cured film was observed with an increase of the sand concentration. A simulated weathering test was performed with partex surfaces cured by a formulation containing 3% sand in the base coat. The losses of the physical properties were found to be lower over the surface treated with the formulation containing sand. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2385–2392, 2002     

Synthesis of tetrazole from α, β—Unsaturated carbonyl fatty acid

Methyl 4-oxo-trans-2-octadecenoate (II), when treated with excess hydrazoic acid in the presence of BF₃-etherate, produced 66% methyl 5-aza-nonadec-trans-2-enoate (4,5-d)-tetrazole (III), 10% methyl 5-aza-nonadec-4-oxo-trans-2-enoate (IV) and 7% pentadecamide (V). Individual products were characterized by spectral and elemental methods.     

Exhaust Emissions from an Engine Fueled with Biodiesel from High-Oleic Soybeans

Biodiesel is a fuel comprising mono-alkyl esters of medium to long-chain fatty acids derived from vegetable oils or animal fats. Typically, engines operated on soybean-based biodiesel exhibit higher emissions of oxides of nitrogen (NOx) compared with petroleum diesel. The increase in NOx emissions might be an inherent characteristic of soybean oil’s polyunsaturation, because the level of saturation is known to affect the biodiesel’s cetane number, which can affect NOx. A feedstock that is mostly monounsaturated (i.e. oleate) helps to balance the tradeoff between cold flow and oxidative stability. Genetic modification has produced a soybean event, designated 335-13, with a fatty acid profile high in oleic acid (>85%) and with reduced palmitic acid (<4%). This high-oleic soybean oil was converted to biodiesel and run in a John Deere 4045T 4.5-L four-stroke, four-cylinder, turbocharged direct-injection diesel engine. The exhaust emissions were compared with those from conventional soybean oil biodiesel and commercial No. 2 diesel fuel. There was a significant reduction in NOx emissions (α = 0.05) using the high-oleic soybean biodiesel compared with regular soybean oil biodiesel. No significant differences were found between the regular and high-oleic biodiesel for unburned hydrocarbon and smoke emissions.     

Treatment of phenol formaldehyde production wastewater by electrooxidation-electrofenton successive processes

ABSTRACT

Treatments of phenol formaldehyde producing wastewater (PFPW) by electrooxidation (EO) and electro-Fenton (EF) successive processes were carried out in a batch electrolytic reactor using graphite (Gr) and stainless steel (Ss) electrodes. After the completion of the EO process, the wastewater was further treated with EF process. The influence of operating variables such as current density, operating time, initial pH_i and H₂O₂ concentration was evaluated for removals of phenol, TOC and COD in PFPW. Gr/Gr, Gr/Ss or Ss/Ss and Ss/Gr electrode pair were used as anode and cathode. The best removal efficiency in the EO process was obtained with Gr/Gr (93%) as compared to Gr/Ss (82%), Ss/Ss (63%) and Ss/Gr (55%). The removal efficiencies for the EO process using Gr-Gr electrode pair were obtained as 93% for phenol, 61% for COD and 44% for TOC at initial pH_i 7,5 g/L of NaCl, 50 mA/cm² and 5 h. In the EF process, the removal efficiencies at pH_i 3,5 mA/cm² and 30 mM H₂O₂ and 45 min were 100% for phenol, 76% for COD and 59% for TOC. This study provided that the successive processes are an effective method for the removal of phenolic compounds from the wastewater.     

Cloning SIM Cards Usability Reduction in Mobile Networks

This paper studies the probability of using cloning subscriber identity module (SIM) cards in Universal Mobile Telecommunications Systems. It also explores how the mobile system can discover the cloning SIM cards as soon as possible and how to reduce the probability of using cloning SIM cards in mobile networks. The illegal mobile station attached to mobile networks can be detected by a Normal Location Area Update, a periodic area location update, and by outgoing calls that are issued from genuine mobiles. An analytical model is developed to investigate the effects of a location area update and outgoing calls issued by genuine mobiles on the use of illegal mobiles. Mobility management, such as registration, cancellation, and outgoing and incoming procedures for legal and illegal users are investigated and analysed. An analytical model to investigate the effect of outgoing call arrival rates, and location area residence time on the detected illegal user has been presented. This paper seeks to increase the security of communication by avoiding fraud of cloned mobile phones by proposing a solution to speed up the detection of cloning SIM cards.     

Adsorption of Cr(III), Ni(II), Zn(II), Co(II) ions onto phenolated wood resin

In this study, phenolated wood resin was used an adsorbent for the removal of Cr(III), Ni(II), Zn(II), Co(II) ions by adsorption from aqueous solution. The adsorption of metal ions from solution was carried at different contact times, concentrations and pHs at room temperature (25°C). For individual metal ion, the amount of metal ions adsorbed per unit weight of phenolated wood resin at equilibrium time increased with increasing concentration and pH. Also, when the amounts of metal ions adsorbed are compared to each other, it was seen that this increase was order of Cr(III) > Ni(II) > Zn(II) > Co(II). This increase was order of Cr(III) > Ni(II) > Co(II) > Zn(II) for commercial phenol–formaldehyde resin. Kinetic studies showed that the adsorption process obeyed the intraparticle diffusion model. It was also determined that adsorption isotherm followed Langmuir and Freundlich models. Adsorption isotherm obtained for commercial phenol–formaldehyde resin was consistent with Freundlich model well. Adsorption capacities from Langmuir isotherm for commercial phenol–formaldehyde resin were higher than those of phenolated wood resin, in the case of individual metal ions. Original adsorption isotherm demonstrated the monolayer coverage of the surface of phenolated wood resin. Adsorption kinetic followed the intraparticle diffusion model. The positive values of ΔG° determined using the equilibrium constants showed that the adsorption was not of spontaneous nature. It was seen that values of distribution coefficient (K_D) decreasing with metal ion concentration in solution at equilibrium (C_e) indicated that the occupation of active surface sites of adsorbent increased with metal ions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2838–2846, 2006     

Corrosion behavior of tempered dual-phase steel embedded in concrete

Dual-phase(DP) steels with different martensite contents were obtained by appropriate heat treatment of an SAE1010 structural carbon steel,which was cheap and widely used in the construction industry. The corrosion behavior of DP steels in con-crete was investigated under various tempering conditions. Intercritical annealing heat treatment was applied to the reinforcing steel to obtain DP steels with different contents of martensite. These DP steels were tempered at 200,300,and 400°C for 45 min and then coo...     

Magnetic Behavior of Trinuclear Vanadium(II)–Diamine Complexes. Part 2. Large Intramolecular Antiferromagnetic Exchange Interactions in a Triangular Unit

This study reports the magnetic structures of newly reported trinuclear vanadium(II)–diamine complexes. Using the isotropic Heisenberg exchange Hamiltonian, it is suggested that there are strong intramolecular antiferromagnetic interactions among the vanadium(II) ions. It is also suggested that these complexes are good candidates to the geometrically frustrated systems. For part 1 see A. Bayri, J. Inorg. Organomet. Polym. Mater., (in press) An erratum to this article can be found at