Determination of optimum pH and temperature for pasteurization of citrus juices by response surface methodology

Summary Optimization of microbial death, enzyme inactivation and vitamin C retention during pasteurization of pH-adjusted orange juice is discussed free of equipmentdependent parameters such as the heating lag. The pH-temperature optimum was determined by response surface methodology in the range of 65° C–75° C and pH 2.5–4.0. The results implied that there was no pectinesterase activity below pH 3.5.Leuconostoc mesenteroides had its maximum and minimum thermal resistance at pH 3.5 and pH 2.7, respectively. For an ideal theoretical process requiring four log cycles of microbial reduction the optimum pasteurization conditions were 12 min at 75° C and pH 2.7.

---

Bestimmung der optimalen Temperatur- und pH-Wert-Bedingungen für die Pasteurisierung von Citrussäften mit der response surface-Methode

Zusammenfassung Die Optimierung der mikrobiellen Abtötung, Enzyminaktivierung und Vitamin-C-Retention während der Pasteurisierung von Orangensaft mit verschiedenen pH-Werten wird, frei von Anlageneinflüssen, wie z. B. Erhitzungsverzögerungen, diskutiert. Das Temperatur-pH-Wert-Optimum wurde mit der response surface-Methode im Temperaturbereich von 65 bis 75 °C und pH-Werten zwischen 2,5 und 4,0 untersucht. Die Ergebnisse lassen darauf schließen, daß unter pH 3,5 keine Pectinesteraseaktivität mehr vorliegt.Leuconostoc mesentroides wies bei pH 2,7 minimale und bei pH 3,5 maximale Hitzeresistenz auf. In einem idealen theoretischen Pasteurisierungsprozeß, der eine Reduzierung der mikrobiellen Belastung um vier Größenordnungen erfordert, liegen die optimalen Bedingungen bei 12 min, 75 °C und einem pH-Wert von 2,7.

     

Interference analysis and capacity for forward link 3G CDMA network with adaptive antennas

In code division multiple access (CDMA) systems, the capacity of forward link (FL) communication to mobile receivers is limited primarily by co‐channel interference (CCI). Adaptive antenna arrays (AAAs) that use antenna arrays along with advanced signal processing at the base station (BS) have been proposed to mitigate this limitation. For a 3G CDMA cellular network, where each BS equipped with an AAA serves mixture of voice and data users within its coverage, we study FL capacity and investigate the effects of different factors (array topology, multipath angle spread, data rate, and beamforming algorithm) on this capacity under Rayleigh fading channel. By modeling the instantaneous signal‐to‐interference power ratio received at the mobile, we derive the system outage equation that considers blocking of either desired voice or data user. Simulation results show that for the same element spacing and number of antenna elements per cell, the uniform circular array (UCA) topology results in larger capacity than the sectorized uniform linear array (ULA) topology does, and that a larger angle spread or data user rate reduces FL capacity. Copyright © 2007 John Wiley & Sons, Ltd.     

Novel T-rail electrodes for substrate removed low-voltage high-speed GaAs/AlGaAs electrooptic modulators

A novel traveling-wave electrode utilizing capacitively loaded T-rail elements was developed for low-voltage high-speed substrate-removed GaAs/AlGaAs electrooptic modulators. Electrodes with varying dimensions were fabricated and characterized. Electrode phase velocity, characteristic impedance, loss coefficient, and capacitive loading were extracted from the measured s-parameters up to 40 GHz. Electrode was also simulated using a finite-element solver. The measured and calculated electrode capacitance values were found to be in excellent agreement, showing that the electrode can be precisely designed. Approaches were outlined to provide a group velocity-matched very high-speed modulator electrode suitable for a low drive-voltage substrate-removed GaAs/AlGaAs electro-optic modulator     

A Robust Wearable Point-of-Care CNT-Based Strain Sensor for Wirelessly Monitoring Throat-Related Illnesses

Point-of-care testing (POC) has the ability to detect chronic and infectious diseases early or at the time of occurrence and provide a state-of-the-art personalized healthcare system. Recently, wearable and flexible sensors have been employed to analyze sweat, glucose, blood, and human skin conditions. However, a flexible sensing system that allows for the real-time monitoring of throat-related illnesses, such as salivary parotid gland swelling caused by flu and mumps, is necessary. Here, for the first time, a wearable, highly flexible, and stretchable piezoresistive sensing patch based on carbon nanotubes (CNTs) is reported, which can record muscle expansion or relaxation in real-time, and thus act as a next-generation POC sensor. The patch offers an excellent gauge factor for in-plane stretching and spatial expansion with low hysteresis. The actual extent of muscle expansion is calculated and the gauge factor for applications entailing volumetric deformations is redefined. Additionally, a bluetooth-low-energy system that tracks muscle activity in real-time and transmits the output signals wirelessly to a smartphone app is utilized. Numerical calculations verify that the low stress and strain lead to excellent mechanical reliability and repeatability. Finally, a dummy muscle is inflated using a pneumatic-based actuator to demonstrate the application of the affixed wearable next-generation POC sensor.     

Hybrid wideband transceiver design for achievable rate maximization in millimeter-wave MIMO systems

Telecommunication Systems - This paper proposes two algorithms for hybrid (Analog–Digital) beamforming in a single-user millimeter-wave (mm-wave) multi-input multi-output (MIMO) systems under...     

Deposition thickness based high-throughput nano-imprint template

International Technology Roadmap for Semiconductors 2003 projected nano-imprint lithography has the potential of high throughput, sub-20 nm resolution, and low cost [S.Y. Chou, P.R. Krauss, P.J. Renstrom, Appl. Phys. Lett. 67 (1995) 3144; Science 272 (1996) 85, J.A. Rogers, C. Mirkin, Mater. Res. Bull. 26 (2001)]. For nano-imprint lithography, a template with 1X resolution is required. The existing industrial infrastructure for supporting deep ultra violet 4X photo masks by e-beam and/or a laser beam scanning writer does not offer pitch (center-to-center distance of an array of patterned lines) less than ∼60 nm [<http://public.itrs.net/2003ITRS>]. For nano-imprint lithography to be accepted across the industry, a reproducible simple fabrication process to make a high resolution, single emboss template is essential [L. Jay Guo, J. Phys. D: Appl. Phys. 37 (2004) R123-R141]. Here we show, a general fabrication method and fabricated nano-imprint templates with sub-15 nm template line width and 10 nm pitch length through out the entire 200 mm wafer, varying the deposition thickness of multiple alternate films, using atomic layer deposition. Although multilayer nano-imprint templates and their exciting use have been demonstrated, [W.J. Dauksher et al., J. Vac. Sci. Technol. B 22 (2004) 3306, B. Heidari, et al., The 49th international conference on electron, ion and photon beam technology and nanofabrication, Orlando, Florida, 2005, William M. Tong, et al., Proc. SPIE 5751 (2005) 46-55, N.A. Melosh, A. Boukai, F. Diana, B. Gerardot, A. Badolato, P.M. Petroff, J.R. Heath, Science 300 (2003) 112] such a small pitch was not shown and either complex lattice mismatch-based epitaxially grown films or unconventional etch chemistry was used. The bare necessity was a simple and economical fabrication process for a high throughput nano-imprint template. In that context, we have developed a template fabrication process using classical micro-fabrication techniques. Successful use of these techniques made the template fabrication process simple, economical, and expedient. Also a novel technique to provide flexible and accurate alignment for nanowire patterning has been described. In this technique, nanowire patterning is accomplished on the entire wafer with a single impression. Industry level batch-fabrication of our scheme illustrates its reproducibility and manufacturability. We anticipate, this simple, economical and time saving technique will help researchers and developers to perform their experiment on nano-scale feature patterned substrates easily and conveniently.     

ANALYSIS OF INTERNALLY GENERATED NOISE OF BIOELECTRIC AMPLIFIERS

This papenr deals with internally generated noise of bioelectric amplifiers that are usually used for processing of bioelectric events.The main purpose of this paper is to present a procedure for analysis of the effects of internal noise generated by the active circuits and to evaluate the output noise of the author‘s new designed bioelectric amplifier that caused by internal effects to the amplifier circuit itself in order to compare it with the noise generated by conventional amplifiers.The obtained analysis results of internally generated noise showed that the total output noise of bioelectric active circuits does not increase when some of their resitors have a larger value.This behavior is caused by the different transfer functions for the signal and the respective noise sources associated with these resistors.Moreover,the new designed bioelectric amplifier haws an output noise less than that for conventional amplifiers.The obtained analysis results were also experimentally verified and the final conclusions were drawn.     

Highly Efficient,Solution‐Processed,Single‐Layer,Electrophosphorescent Diodes and the Effect of Molecular Dipole Moment

A new family of highly soluble electrophosphorescent dopants based on a series of tris‐cyclometalated iridium(III) complexes (1–4) of 2‐(carbazol‐3‐yl)‐4/5‐R‐pyridine ligands with varying molecular dipole strengths have been synthesized. Highly efficient, solution‐processed, single‐layer, electrophosphorescent diodes utilizing these complexes have been prepared and characterized. The high triplet energy poly(9‐vinylcarbazole) PVK is used as a host polymer doped with 2‐(4‐biphenylyl)‐5‐(4‐tert‐butyl‐phenyl)‐1,3,4‐oxadiazole (PBD) for electron transport. Devices with a current efficiency of 40 cd A^?1 corresponding to an EQE of 12% can thus be achieved. The effect of the type and position of the substituent (electron‐withdrawing group (CF₃) and electron‐donating group (OMe)) on the molecular dipole moment of the complexes has been investigated. A correlation between the absorption strength of the singlet metal‐to‐ligand charge‐transfer (¹MLCT) transition and the luminance spectral red shift as a function of solvent polarity is observed. The strength of the transition dipole moments for complexes 1–4 has also been obtained from TD‐DFT computations, and is found to be consistent with the observed molecular dipole moments of these complexes. The relatively long lifetime of the excitons of the phosphorescence (microseconds) compared to the charge‐carrier scattering time (less than nanoseconds), allows the transition dipole moment to be considered as a “quasi permanent dipole”. Therefore, the carrier mobility is sufficiently affected by the long‐lived transition dipole moments of the phosphorescent molecules, which are randomly oriented in the medium. The dopant dipoles cause positional and energetic disorder because of the locally modified polarization energy. Furthermore, the electron‐withdrawing group CF₃ induces strong carrier dispersion that enhances the electron mobility. Therefore, the strong transition dipole moment in complexes 3 and 4 perturbs both electron and hole mobilities, yielding a reduction in exciton formation and an increase in the device dark current, thereby decreasing the device efficiency.     

Collision avoidance slot allocation scheme for multi-cluster wireless sensor networks

This paper introduces a collision avoidance slot allocation scheme for Time Division Multiple Access (TDMA) based Medium Access Control (MAC) in multi-cluster wireless sensor networks. TDMA MAC protocols have built-in active-sleep duty cycle that can be leveraged for limiting idle listening. Also, they can overcome the overhearing problem, thus have better energy efficiency. Enabling concurrent intra-cluster communications using a single radio channel is a key issue in TDMA MAC protocols. Using orthogonal frequency channels or different Code Division Multiple Access codes for different adjacent clusters can solve the problem at the expense of cost. In this paper, we propose a new distributed slot allocation protocol called  Coordinated   Time   Slot   Allocation (CTSA) that can reduce collisions significantly using a single radio channel. We use simulations to study the effects of different system parameters on the performance of our proposed protocol. Simulation results show that applying CTSA over clustering protocols can significantly reduce collisions. It also shows fast convergence for our proposed CTSA protocol. In this paper we apply our CTSA scheme to the Low Energy Adaptive Clustering Hierarchy protocol which forms the basis for many cluster based routing protocols. CTSA is also compared with the SRSA algorithm proposed by Wu and Biswas (Wirel Netw 13(5):691–703, 2007) by means of simulation.