Analytic approach to the computation of the temperature distribution in multilayer structures under heating by cw scanning laser radiation

By using integral transform methods, an approach is developed to the solution of a problem on the temprature distribution in multilayer structures heated by cw scanning laser radiation, with phase transitions in the layers taken into account.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 53, No. 6, pp. 1000–1010, December, 1987.     

“Metallisation” of oxide surfaces observed by in situ high-resolution electron microscopy

Intense irradiation (25–40 A/cm²) at intermediate energy (400 keV) has been found to cause “metallisation” of tungsten oxide and titanium niobate crystal surfaces. The possible mechanisms and the likely consequences for high-resolution imaging of clean oxide surfaces are briefly discussed.     

Comparison of Solutions of the Problems of Elasticity Theory for Different Near-Boundary Elements

We consider three types of near-boundary elements: curvilinear quadrangles and families of arcs and points, and their application to a two-dimensional problem of the static theory of elasticity with boundary conditions in displacements. The comparison of the theoretical and numerical aspects of the obtained solutions is performed. It is shown that the accuracy of evaluation of the components of the vector of displacements increases in the following cases: in the case of complete quantization of the near-boundary region (but not in the case of its partial quantization or quantization with overlapping), in the case where the numbers of arcs and points increase, and in the case of simultaneous application of different types of near-boundary elements (specifically, quadrangles and families of arcs).     

The first accurate measurement of systolic and diastolic bloodpressure

Poiseuille, known for his law of fluid flow, which is the analog of Ohm's law, introduced the units (mmHg) by which we measure blood pressure by using the mercury manometer, which he described in his medical school thesis in 1828. For 50 years, mean blood pressure was all that could be measured because of the long response time of the mercury manometer. It is true that the height of the mercury column displayed pulsatile oscillations, but their amplitude was much less than that of pulse pressure. It is interesting to note that the slowly responding mercury manometer was made to display first systolic then diastolic pressure by means of an ingenious device that contained two oppositely directed check valves. It took from 1828 to 1903 for high-fidelity graphic recordings of blood pressure to appear in which systolic and diastolic pressures were believable. However, systolic and diastolic pressures were measurable since 1878 when Golz and Gaule created their ingenious valved device that permitted use of the slowly responding mercury manometer to display these pressures accurately     

Simulation of magnetic component models in electric circuitsincluding dynamic thermal effects

It is essential in the simulation of power electronics applications to model magnetic components accurately. In addition to modeling the nonlinear hysteresis behavior, eddy currents and winding losses must be included to provide a realistic model. In practice the losses in magnetic components give rise to significant temperature increases which can lead to major changes in the component behavior. In this paper a model of magnetic components is presented which integrates a nonlinear model of hysteresis, electro-magnetic windings and thermal behavior in a single model for use in circuit simulation of power electronics systems. Measurements and simulations are presented which demonstrate the accuracy of the approach for the electrical, magnetic and thermal domains across a variety of operating conditions, including static thermal conditions and dynamic self heating     

Modern Aluminum and Magnesium Alloys and Composite Materials Based on Them

Aluminum and magnesium alloys are the base structural materials in aircraft and spacecraft engineering. The main stages of the development and introduction of light alloys are described.     

高级控制系统提高巴西水电站性能

巴西的一个重要电力公司COPEL最近开发了一个水电站高级控制系统，这是在电力部门经受重大变革时期，提高水电竞争力的里程碑。     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.