Explosive compaction of amorphous Cu−Sn powder prepared by the method of mechanical alloying

Novosibirsk. Translated from Fizika Goreniya i Vzryva, Vol. 25, No. 2, pp. 125–129, March–April, 1989.     

Crust formation in the blast-furnace stack

Conclusions It was established that the crust forming on the lining of the blast-furnace stack can be divided into two genetic varieties, viz., mass-exchange and metallurgical crusts.The formation of a mass-exchange crust on the stack lining must be prevented by constructing the lining of high-density, thermally and chemically stable refractory minerals. At the same time it is advantageous to create conditions which favor the formation of a protective metallurgical crust on the surface of the lining.Translated from Ogneupory, No, 2, pp. 39–42, February, 1976.     

The electrochemical synthesis of aminonitriles I. H-cell studies with adiponitrile and azelanitrile

Adiponitrile and azelanitrile were electrochemically hydrogenated to their corresponding aminonitriles in a divided H-cell using Raney nickel powder as the cathode material. The effects of current, temperature, and solvent/supporting electrolyte composition on product selectivities were investigated. Syntheses of the fully hydrogenated diamine by-product increased with increasing current and solution temperature. When a 0.8 M adiponitrile/alcohol/water/ammonium actetate electrolyte was hydrogenated at temperatures of 35–45°C, 6-aminocapronitrile selectivities in the range of 79–97% and current efficiencies of 50–60% were obtained. The optimum applied current was 60 mA for each 2.5 g of catalyst (an apparent current density of 4.8 mA cm^–2). For the case of azelanitrile, reaction selectivities for the partially hydrogenated 9-aminononanenitrile product ranged from 80–93%.     

The effect of fillers on strength of cement mortars

The effect of three fillers (ground limestone, dolomite and basalt) on the strength of cement mortars was studied on 1:2.75 mixes having a w/c ratio of 0.70. The filler content ranged from 10 to 40% of the cement weight and their fineness (specific surface) from 1,150 to 11,200 sq. cm per g. Results confirmed earlier conclusions that fillers effect on strength is primarily an accelerating effect on the cement hydration. The improvement in strength is essentially the same for all non-pozzolonic fillers increasing with both filler content and fineness. In part, this improvement in strength is attributable to the increase in the density of the mix (i.e. a lower air content) associated with the use of fillers. There is some indirect evidence that monocalcium carboaluminate is formed when the finest limestone filler (10,300 sq. cm per g) is used. This formation, however, apparently does not affect strength.     

An evaluation of the performance of an automated procedure for comparative modelling of protein tertiary structure

A 3-D model of a protein can be constructed from its amino acidsequence and the 3-D structures of one or more homologues byannealing three sets of fragments: the structurally conservedregions, structurally variable regions and the side chains.The method encoded in the computer program COMPOSER was assessedby generating 3-D models of eight proteins whose crystal structuresare already known and for which 3-D structures of homologuesare available. In the structurally conserved regions, differencesbetween modelled and X-ray structures are smaller than the differencesbetween the X-ray structures of the modelled protein and thehomologues used to build the model. When several homologuesare used, the contributions of the known structures are weighted,preferably by the square of sequence similarity; this is especiallyimportant when the similarities of the homologues to the modelledstructure differ greatly. The ‘collar’ extensionapproach, in which a similar region of different length in ahomologue is used to extend the framework, can result in a moreaccurate model. If known homologues comprise more than one relatedgroup of proteins and they are both distantly related to theunknown, then alignment of the sequence to be modelled witheach group of homologues facilitates identification of structurallyconserved regions of the unknown and leads to an improved model.Models have root mean square differences (r.m.s.d.s) with thestructures defined by X-ray analysis of between 0.73 and 1.56Å for all C atoms, for seven of the eight models. Forthe model of mucor pepsin, where the closest homologue has 33%sequence identity and 20% of the residues are in structurallyvariable regions, the r.m.s.d. for the framework region is 1.71Å and the r.m.s.d. for all C atoms is 3.47 Â.     

Behavior of biliary phospholipids in intestinal lumen during fat digestion in rat

The phospholipids present in the intestinal lumen of rats following ingestion of triglycerides are of biliary origin. They consist of lecithins accompanied by a small proportion of lysolecithins. Their behavior in comparison with the other lipid constituents of the intestinal content was studied by subjecting the latter to gel filtration on an agarose column in the presence of a solution of 6 mM sodium taurocholate in 0.1 M NaCl. Part of the phospholipids is present with the triglycerides and diglycerides in the emulsified phase excluded from the gel where pancreatic lipase and colipase also are found. The remainder is found in optically clear fractions containing fatty acids, monoglycerides, and bile salts. These fractions are eluted at 2.0 column volumes, while mixed fatty acids, monoglycerides, bile salts micelles emerge from the column at 2.4 column volumes in the same chromatographic conditions. This difference in behavior may be explained by the presence of biliary lecithins. This presence could have an important bearing upon the mucosal uptake of the lipolysis products of triglycerides.     

Graft-copolymerization of starch with acrylamide,II. Thermal behaviour of graft copolymers

Thermal behaviour of starch-graft-polyacrylamide (S-g-PAM) copolymers was evaluated. Grafting of polyacrylamide onto starch lowers the initial decomposition temperature. However, the over-all stability as assessed by the shape of thermogravimetric curve and integral procedural decomposition temperature increased with an increase in % graft-on.     

Life of stopper heads in continuous steel casting

Conclusions Chamotte heads with 5, 10 and 15% graphite differ from conventional chamotte by high thermal endurance, thermal conductivity and wear resistance. The increased rigidity of stopper heads with a graphite content of 5 to 15% used in combination with magnesite sleeves enhances the formation of longitudinal cracks.Chamotte specimens fired at 1230° C are endowed with high wear-resistance. They differ from conventional chamotte refractories by higher thermal endurance and provide for good stopper service in reladling killed steel.High-alumina SP-9-type heads made at Chasov-Yar Combine wear less in intermediate ladles and are endowed with greater thermal strength than chamotte heads.The higher quality of the chamotte heads under conditions of Stalino Metallurgical Plant in comparison to that of Krasnoye Sormovo Plant is not only due to the quality of the refractory but also to such factors as the rate and degree of preheating intermediate ladles before filling with metal, careful placement of the stoppers, and use of graphite packing around the teeming head.Despite higher wear SP-12-type chamotte heads made at Chasov-Yar Combine allowed normal teeming of rimmed steel in 50 ton ladles.To ensure a steady service of the stoppers in continuous steel casting the preheating of intermediate ladles of 1300 and the use of precooled stoppers are recommended.