Preparation,Properties and Applications of the Hybrid Organic/Inorganic Nanocomposite Based on Nanoporous Carbon Matrix

Journal of Inorganic and Organometallic Polymers and Materials - Nanoporous carbon matrix was prepared by the sol–gel process from pyrogallol-formaldehyde (PF) mixtures in water using picric...     

Mechanical and Corrosion Properties of ZrB2–SiC Composite Ceramics with Oxide Additions

Powder Metallurgy and Metal Ceramics - Hot pressing was used to produce compact ceramic samples with the following composition (wt.%): 60 ZrB2 + 20 SiC + 20 (Al2O3 + 32 t-ZrO2). The tetragonal...     

A Heat Treatment to Produce a Coarse-α-Particle Size in Ti–6Al–4V

Metallurgical and Materials Transactions A - A heat-treatment method to develop a coarse-α-particle size in Ti–6Al–4V with a fully-globular (equiaxed) microstructure was developed....     

Thermal Modeling of Tool-Work Interface during Friction Stir Welding Process

Russian Journal of Non-Ferrous Metals - Adequate heat input provided by the proper combination of friction stir welding (FSW) parameters is critical to sound welding. Optimum parameter setting...     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

Examination of Pellets Made from Concentrate of Oxidized Ferruginous Quartzites of Mikhailovsky GOK

Metallurgist - The production of pellets from a concentrate of oxidized ferruginous quartzites that are tailings at the Mikhailovsky GOK pelletizing plant is studied. The conditions for the...     

A Model of the Dynamics of Heat Exchange and Control of the Cooling Process in a Moving Dense Layer of Hot Blast Furnace Slag

Metallurgist - Within the framework of solving the problem of analyzing and evaluating the practical implementation of dry granulation of BF slag, a mathematical model of the dynamics of heat...     

Use of electron microscopy on microstructure characterization of high chromium cast irons

The physical metallurgy underlying the development of cast microstructures in abrasion resistant high chromium cast irons, and their structural modification by thermal treatments is relatively complex. Structural characterisation via electron microscopy therefore has a key role to play in furthering our understanding of the phase transformations that control the microstructures and hence the service performances of these irons as wear parts. This paper shows how both scanning and especially transmission electron microscopy can provide valuable information on the nature of eutectic and secondary carbides and on the matrix structures in these irons. Particular attention is given to current characterisation research on conventionally cast 30%Cr irons that are used for applications involving corrosive wear e.g. slurry pumps and on a semi-solid cast 27%Cr iron that has a potential for applications in industry.