Optical fiber up-tapers with index perturbations-performanceanalysis

The performance of step index up-tapers subjected to certain index perturbations in investigated by computer simulation. Concentric symmetric and asymmetric index profile perturbations as well as localized spherical, called regions bubbles, having a different index are studied. It is found that some low-valued perturbations of small scale size (less than a wavelength) do not alter the optical fiber performance. However, the amount of beam expansion in the up-taper may be ultimately limited by such perturbations. Excessive magnification in the presence of perturbations can cause a distortion of the quasi-Gaussian shape and symmetry of the pure step-index fundamental mode as well as increase the excess loss and degrade the lateral and axial displacement tolerance improvements of the up-tapers. For example, an index variation of Δn≈10^-5 in conjunction with a perturbation scale size of 40 μm can be detrimental. Bubble-type perturbations could also cause similar problems. A single 12.8-μm-diameter bubble with a relative index of -0.02, embedded in a 128-μm-diameter step index core with relative index of 0.5%, produced a 0.3-dB excess loss     

FSK heterodyne transmission experiments at 560 Mbit/s and 1 Gbit/s

Optical frequency-shift-keying (FSK) signals are obtained from directly modulated distributed feedback (DFB) semiconductor lasers. Experimental studies of the direct frequency modulation (FM) characteristics of the DFB lasers show a nonuniform FM response due to the competing effects of thermal modulation of the laser active region and carrier density modulation. Equalization of the signal current to the laser is employed to produce a flat FM response from 30 kHz to 1 GHz. Optical FSK transmission and heterodyne detection experiments at 560-Mbit/s and 1-Gbit/s are conducted at a wavelength of 1497 nm. Receiver sensitivities of -39 dBm at 560 Mbit/s and -37 dBm at 1 Gbit/s are obtained. Transmission through 100 km of single-mode fiber at 1 Gbit/s is achieved with no degradation in receiver sensitivity.     

A direct algorithm for continuous path control of manipulators

This paper presents an algorithm for positioning and orientation of the hand for a redundant or non-redundant manipulator along a continuous path in space. This algorithm minimizes the distance between the actual position of the tip of the end-effector and the desired path. The algorithm does not use the Jacobian matrix for the inverse kinematics of the robot. It takes full advantage of the resolution of the joint drives, avoids singularity problems, and can be used for both redundant manipulators. The algorithm can be used in any situation where continuus motion of the end-effector is required in an open loop mode.     

Pull-out and fragmentation in model fibre composites

An experimental study has been carried out of debonding and fibre rupture in model composites. A single glass rod or fibre was embedded in the centre of a long transparent silicone rubber block. Strains in the rubber in close proximity to the rod or fibre were measured as the specimen was slowly stretched. Pull-out forces, strain distributions, and debonded lengths are compared with the predictions of a simple theory based on a fracture energy criterion for debonding, and taking into account friction at the debonded interface. Experiments were carried out with rods of different diameter, rubber blocks of varied cross-section, and with two levels of adhesion. By extrapolating the debonded length to zero, values of the debonding force in the absence of friction were obtained. They were in accord with fracture energies of about 50 J/m² for weak bonding and about 200 J/m² for strong bonding. Fibre fragmentation lengths were measured also. They were in reasonable agreement with the inferred fracture energies and the measured frictional properties of silicone rubber sliding on glass. In a separate study, it was found that the frictional stress between cast silicone rubber and glass was approximately constant, about 0.1 MPa, rather than proportional to pressure, for pressures exceeding about 0.02 MPa. This feature is attributed to a particularly smooth interface between the two materials.     

Stability of Fe3+ — VO defect pairs in polycrystalline Pb(Ti,Zr)O3

The intensity of the EPR signal with g = 5.985 arising from a ferric ion — oxygen vacancy defect pair (Fe³⁺ — V_O) in PbTiO₃, varies with the extent of PbO nonstoichiometry at constant Fe³⁺ content due to an increased oxygen vacancy concentration. In PZT solid solutions, the signal intensity decreases with an increase in Zr. A lower intensity is also noticed for Fe³⁺ — V_O signals in PbZrO₃. This behaviour is explained on the basis of PbO nonstoichiometry arising from independent Pb- and O-vacancies as well as the randomly distributed crystallographic shear (CS) plane defects. The contribution to PbO nonstoichiometry from CS planes is larger in high zirconium compositions of PZT.     

Application of Romero García method to the degradation process of DGEBA/ETDA filled with ultra fine metallic copper

Summary The thermal properties of an epoxy resin (diglycidyl ether Bisphenol A, DGEBA) cured with a primary amine (ethylenediamine, ETDA) and filled with 10, 20 and 30 wt. % of ultra fine copper particles were analyzed. The thermal results were evaluated by means of the Romero-Garcia method, which allowed to obtain the resin degradation kinetic parameters, as well as the possible decomposition mechanism. From the obtained results is possible to infer that higger copper content strongly affects the degradation process of the epoxy resin, which causes a drop off on the composites thermal stability. This behavior could be attributed to water presence, being this effect less pronounced for the resin with 10 wt. % copper and unfilled resin. Regarding to decomposition mechanism, three way transport showed the best correlation for all samples.     

Determination of siphon operating regimes

Necessary and sufficient conditions are found for continuous and periodic liquid motion in systems containing siphons.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 52, No. 6, pp. 916–920, June, 1987.     

Electroluminescence spectroscopy for reliability investigations of 1.55 μm bulk semiconductor optical amplifier

This paper demonstrates the complementary relation between functional parameters and electroluminescence spectroscopy for reliability investigations of 1550 nm Semiconductor Optical Amplifiers of 700 μm length active region. Ageing tests have been set to 270 mA-100 °C-1500 h and realized on two different wafers showing more impact on wafer 1 than on wafer 2. Our investigations are particularly focused on interpretation of electroluminescence spectra, from reference and aged SOAs of wafer 1, leading to an improvement of degradation mechanisms understanding. The shift rate to lower energies of the recombination energy peak at 1550 nm, as reported by electroluminescence spectra between reference and aged SOAs in relation with the decrease of optical power measured at 200 mA for the degraded SOA and completed by I(V) characterizations, suggest occurrence of non radiative deep centers near the buried ridge structure in relation with the cleaning process uniformity of interfaces before epitaxial overgrowth. These defects mainly trap majority injected carriers instead of minority carriers reducing the luminescence in the active zone. By monitoring the most sensitive failure indicator (pseudo-threshold current), lifetime distributions are also calculated to determine failure rate, between 150 and 200 FITs over 15 years for operating conditions (25 °C-200 mA) using experimental degradation laws and statistic computations, demonstrating the overall robustness of this technology.