A comparison of stress intensity factors obtained through crack closure integral and other approaches using eXtended element-free Galerkin method

In this paper, a new approach for extracting stress intensity factors (SIFs) by the extended element-free Galerkin method, through a crack closure integral (CCI) scheme, is proposed. The CCI calculation is used in conjunction with a local smoothing technique to improve the accuracy of the computed SIFs in a number of case studies of linear elastic fracture mechanics. The cases involve problems of mixed-mode, curved crack and thermo-mechanical loading. The SIFs by CCI, displacement and stress methods are compared with those based on the M-integral technique reported in the literature. The proposed CCI method involves very simple relations, and still gives good accuracy. The convergence of the results is also examined.     

Tape Cast Multilayer Composite of Nano Zirconia with High Toughness

During the last decade, worldwide attention of researchers has focused on nano-ceramic composites with superior mechanical behavior and improved reliability for structural applications. Here we report the development of a multi-layer composite (MLC) of tape cast nano zirconia with high failure energy. The MLC samples were fabricated by thermocompression of green tapes prepared from 3 mole % yttria stabilized zirconia (3-YSZ) powder with a primary crystallite size of 27 nm. Depending on the number of layers, the MLC samples exhibited failure energy (238.97 KJm^-3) more than two times higher than that of the single tape (≈107 KJm^-3) with a reasonably high bi-axial flexural strength (≈630 MPa), high hardness (≈ 13 GPa at 49 N), and indentation fracture toughness nearly four times as high as that of the single tape. In addition, these MLC materials showed the presence of a R-curve behavior.     

Microfluorometric detection of catecholamines with multiphoton-excited fluorescence

We demonstrate sensitive spatially resolved detection of physiological chromophores that emit in the ultraviolet (<330 nm). An atypical laser source (a visible wavelength femtosecond optical parametric oscillator), and an unconventional collection geometry (a lensless detector that detects the forward-emitted fluorescence) enable this detection. We report the excitation spectra of the catecholamines dopamine and norepinephrine, together with near-UV emitters serotonin and tryptophan, in the range of 550-595 nm. We estimate the molecular two-photon action cross section of dopamine, norepinephrine, and serotonin to be 1.2 mGM (1 GM, or Goppert Mayor, is equal to 10(-58) m4 s(-1) photon(-1)), 2 mGM, and 43 mGM, respectively, at 560 nm. The sensitivity achieved by this method holds promise for the microscopic imaging of vesicular catecholamines in live cells.     

Mechanical behavior of glass polymer multilayer composites

To identify the best reinforcement condition for development of tough glass polymer multi-layer composites (GPMLC) with high failure strain, two such model composite structures were developed. Soda–lime–silica glasses of two different thicknesses viz (A—1.01 mm and B—1.17 mm) were used as the matrix layers. The A-glass and B-glass based GPMLC samples were prepared by a novel, low pressure lamination technique applied to the alternating planar structure of the matrix and reinforcing phases. These GPMLC materials were fabricated with and without a thin sprayed layer of kerosene, between the glass layer and the reinforcing layer in the interface where; the interface was either epoxy (a thermosetting resin) or polyvinyl butyral (PVB, a thermoplastic resin). The GPMLC samples which exhibited stepped load—displacement behaviour in the most pronounced fashion, had the thermoplastic resin at the interface. Most of these GPMLC samples had a thin layer of kerosene intentionally introduced between the glass layer and the reinforcing polymer layer such that a weak interface is obtained. Fractographic evidence suggested that more of controlled delaminaton cracking occurs in such samples. Apart from the chemical nature of the reinforcing polymer phase, the interfacial layer thickness (h _i ) and the interfacial shear stress ( _xy ) were found out to have significant influence on the specific failure load and the failure stress of the current glass polymer multi-layer composites.     

Nanosized bismuth ferrite powder prepared through sonochemical and microemulsion techniques

Two processing routes, namely sonochemical and microemulsion have been exploited to prepare bismuth ferrite powders. Phase pure nanosized BiFeO₃ powders are prepared by sonochemical and microemulsion techniques in the temperature range of 400 °C and at 500 °C which is much lower than that of the conventional preparation methods. The XRD obtained from both cases was likely to be pure bismuth ferrite. Though the microemulsion based powders showed slightly better properties with respect to particle size, surface area, and final density, sonochemically prepared powders may be more acceptable considering the ease of preparation and cost effectiveness.     

A new image binarization method using iterative partitioning

This paper proposes a new method for image binarization that uses an iterative partitioning approach. The proposed method has been tested towards binarization of both document and graphic images. The quantitative comparisons with other standard methods reveal that the proposed approach outperforms existing widely used binarization techniques in terms of accuracy of binarization. The experimental results further establish the superiority of the proposed method, especially for degraded documents and graphic images. The proposed algorithm is suitable for a multi-core processing environment as it can be split into multiple parallel units of executions after the initial partitioning.     

Effects of neutralization on the structure and properties of an ionomer

The structure, morphology, and properties of an ionomer, poly(ethylene‐acrylic‐acid) neutralized by zinc salts (PI) depend on the free carboxylic acid content. In this work, metal acetates (Na, Zn, and Al acetates) were used to control the neutralization levels. A wide range of techniques were used, such as spectroscopic Fourier transform infrared spectroscopy (FTIR), thermal [thermogravimetric analysis, modulated differential scanning calorimetry (MDSC), and dynamic mechanical analysis (DMA)], mechanical (tensile measurement), and small angle neutron scattering (SANS). The melt rheological properties of the samples were also examined. The results show that metal acetate neutralizes free acrylic acid in the ionomer, which has the primary role in controlling ionic association. The number of ionic groups in ionic domains and multiplets in the matrix is dependent on the neutralization level. Metal valence determines the ionic domain or multiplet structure (FTIR), further properties of PI. Dynamic mechanical properties, the ionic transition behaviour, and the mechanical properties are improved compared with PI using monovalent cation (Na⁺), but decreased using trivalent cation (Al³⁺) or shows less significant changes due to steric effects. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of process parameters on the formation of Silicalite-1 zeolite particles

Silicalite-1 particles with minimum twinning have been synthesized inside the polar core of non-ionic surfactant/co-surfactant-stabilized water-in-oil (w/o) type emulsions at 150° ± 1 °C within a short reaction time of 5 h. The non-ionic surfactants of varying hydrophilic–lipophilic balance (HLB) values, i.e. sorbitan monooleate (Span 80, HLB: 4.3), sorbitan monolaurate (Span 20, HLB: 8.6), polyoxyethylene (4) lauryl ether (Brij 30, HLB: 9.7) and polyoxyethylene sorbitan monooleate (Tween 80, HLB: 15), the cationic surfactant, i.e. cetyl trimethyl ammonium bromide (CTAB), surfactant concentration, co-surfactant, synthesis temperature and time have been found to play significant role in controlling size and characteristics of Silicalite-1. It has been observed that the crystallinity and size of Silicalite-1 can be tailored by adjusting the interactions between the polar surfactant head groups at the w/o interface and the growing crystallographic surfaces (or silicate/TPA ions) in the aqueous medium of the emulsion.     

Thermal stresses in an infinite non-isotropic plate having a penny-shaped crack

Of concern in the paper is the distribution of thermal stresses in the vicinity of a penny-shaped crack in a thick elastic plate made of a non-isotropic material. The problem pertains to the situation where the crack is opened by a prescribed normal pressure and a prescribed heat-flux or a prescribed temperature.