分割电极片状压电致动器——(二)位移特性及狭缝宽度对其影响的实验研究

研究了悬臂梁式分割电极片状压电致动器的位移特性。理论分析表明，分割电极狭缝宽度会减小致动器自由端的位移输出，但当狭缝宽度小于致动器电极宽度的１０％时，可忽略狭缝宽度的影响。致动器端部位移的测试结果大于理论计算值。与现有磁头悬浮臂尺寸相近的致动器，在２０Ｖ～５０Ｖ的电压驱动下均可获得１μｍ～２μｍ的致动位移。对９８５０道／厘米的密度磁盘，该位移能覆盖至少一个磁道宽度，满足磁头定位两级伺服系统对第二级致动器位移的基本要求。     

Pore size control of porous silica by sol-gel process

Porous silica glass was prepared by sol-gel process from tetraethoxysilane (TEOS). The effects of solvents (water, ethanol), drying condition, heat treatment temperature on specific surface area and pore size distribution of porous silica were investigated. Gelation process accelerates with an increase of H₂O content, while retards with the increase of ethanol amount. Structure changes during heat treatment were studied by means of DTA, XRD. TEM micrographs show that the gel particles shrink after heated at 500°C, thus the average pore size decreases.     

Preparation and optical properties of CdxHg1-xTe doped silica glass

In this paper, the Cd_xHg_1-xTe (x=1-0.7) doped silica glass was prepared through two step sol-gel process and in-situ growth technique from tetraethoxysilane (TEOS), cadmium acetate, mercury acetate and telluric acid. The influence of various factors on the glass was studied. The structure of the microcrystals was investigated by XRD. The absorption and transmittance spectrum of the composite showed that the shift of absorption edge was in conformity with the quantum size effect. The third-order nonlinear optical susceptibility χ⁽³⁾ was measured by the degenerate four wave mixing (DFWM). The values of χ⁽³⁾ was in the range of 10^-11-10^-12 MO esu at wavelength of 1.06 μm.     

Using thermally stimulated currents to find defective capacitors

BaTiO₃ multilayer capacitors with a nominal capacitance of 3.5nF have been carefully measured using the thermally stimulated current (TSC) technique. When a 300V polarization voltage is applied at room temperature, a new TSC peak appeared in defective sample A after it has been immersed in water. No new peak was found in good-quality sample B after a similar treatment. The accelerated life test shows that sample A hasa much shorter life than sample B in terms of insulation resistance.     

TEM method for rapid and precise evaluation of continuous recrystallization

With the aid of a double-tilt holder in a transmission electron microscope, a new method for a rapid and precise determination of the misorientations of a large number of subgrain or grain boundaries is given in this article. By use of the method, the continuous recrystallization can be rapidly and precisely evaluated when compared to the other conventional methods.     

“香山81号院”（半山枫林二期）外环境设计

1“居山”与”隐贵山居“ 回想一下人类的聚居行为颇为有趣，当年我们的祖先拼命从险山恶水的自然环境中挣脱出来，为的是得到更加安全和便利的聚居条件，但似乎从那一刻起本能式的回归意识便时刻魂牵梦绕，隐隐作响。其实无论是脱离自然还是回归自然，对于现实而言两者皆是虚幻和理想的。     

En/Decoder for Spectral Phase-Coded OCDMA System Based on Amplitude Sampled FBG

A novel en/decoder for spectral phase-coded optical code-division multiple-access system based on amplitude sampled fiber Bragg grating (FBG) is proposed. Both equivalent chirp and equivalent phase shift are achieved by amplitude sampling. Compared with previous en/decoder based on step chirped FBG, it is easier to fabricate. The performance of the proposed en/decoder is verified by both numerical simulation and experimental demonstration.     

Epoxidation of high trans‐1,4‐polyisoprene and its properties

A new organic‐solvent‐free water‐phase suspension method was used to synthesize partially epoxidized high trans‐1,4‐polyisoprene (TPI) to improve its properties, including oil resistance and wet‐skid resistance. The epoxidation was conducted in an aqueous peracetic acid solution and on the TPI granules prepared by a bulk precipitation method with supported titanium catalyst. The effects of the synthesis conditions, including reaction temperature, reaction time, and pH value, on the epoxy content were investigated. Epoxidized trans‐1,4‐polyisoprene (ETPI) with epoxy contents between 10 and 80% were obtained within 4 h. Both the amorphous and crystalline regions of TPI were epoxidized. The crystallization properties decreased with increasing epoxy content. ETPIs possessed lower mechanical properties than TPI but could be enhanced by vulcanization. The oil resistance and wet‐skid resistance were significantly improved after epoxidation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of a novel proton‐exchange membrane for fuel cells operating at high temperatures and low humidities

The synthesis of a p‐toluidine/formaldehyde (PTF) resin was performed, and the effects of the molar ratio of the individual monomers and the polymerization conditions on the structure of the PTF resin were studied. Fourier transform infrared and ¹³C‐NMR spectra were used to characterize the PTF. Wide‐angle X‐ray diffraction patterns revealed the crystalline structures of various PTFs. Polarized optical microscopy revealed that the molar ratio of the monomers had a strong effect on the crystalline morphologies. A longer polymerization time turned out a polymer with a higher intrinsic viscosity and molecular weight, which led to differences in the proton conductivity. All of the PTFs showed a higher proton conductivity than a commercial Nafion membrane at 90–100°C and 0% relative humidity. The proton conductivity of the PTF series could be improved by sulfonation with sulfuric acid and could be maintained after blending with polyurethane. Pure methanol could be used as a fuel source because of the insolubility and nonwetting properties of PTF in methanol to increase the output current density for a PTF membrane electrode assembly. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Preparation and adsorption behavior of a cellulose‐based,mixed‐mode adsorbent with a benzylamine ligand for expanded bed applications

A novel mixed‐mode expanded bed adsorbent with anion‐exchange properties was explored with benzylamine as the functional ligand. The cellulose composite matrix, densified with stainless steel powder, was prepared with the method of water‐in‐oil suspension thermal regeneration. High activation levels of the cellulose matrix were obtained with allyl bromide because of the relative inertness of the allyl group under the conditions of the activation reaction. After the formation of the bromohydrin with N‐bromosuccinimide and coupling with benzylamine, the activated matrix was derived to function as a mixed‐mode adsorbent containing both hydrophobic and ionic groups. The protein adsorption capacity was investigated with bovine serum albumin as a model protein. The results indicated that the prepared adsorbent could bind bovine serum albumin with a high adsorption capacity, and it showed salt tolerance. Effective desorption was achieved by a pH adjustment across the isoelectric point of the protein. The interactions between the cell and adsorbent were studied, and the bioadhesion was shielded by the adjustment of the salt concentration above 0.1M. Stable fluidization in the expanded bed was obtained even in a 2% (dry weight) yeast suspension. The direct capture of target proteins from a biomass‐containing feedstock without extra dilution steps could be expected with the mixed‐mode adsorbent prepared in this work, and this would be especially appropriate for expanded bed adsorption applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008