InxGa1−xAs ohmic contacts to n-type GaAs with a tungsten nitride barrier

Significant reduction of the contact resistance of In_0.7Ga_0.3As/Ni/W contacts (which were previously developed by sputtering in our laboratory) was achieved by depositing a W₂N barrier layer between the Ni layer and W layer. The In_0.7Ga_0.3 As/Ni/W₂N/W contact prepared by the radio-frequency sputtering technique showed the lowest contact resistance of 0.2 Ωmm after annealing at 550°C for 10 s. This contact also provided a smooth surface, good reproducibility, and excellent thermal stability at 400°C. The polycrystalline W₂N layer was found to suppress the In diffusion to the contact surface, leading to improvement of the surface morphology and an increase in the total area of the In_xGa−As between metal and the GaAs substrate. These improvements are believed to reduce the contact resistance.     

Spray Pyrolysis of Fe3O4–BaTiO3 Composite Particles

Fe₃O₄–BaTiO₃ composite particles were successfully prepared by ultrasonic spray pyrolysis. A mixture of iron(III) nitrate, barium acetate and titanium tetrachloride aqueous solution were atomized into the mist, and the mist was dried and pyrolyzed in N₂ (90%) and H₂ (10%) atmosphere. Fe₃O₄–BaTiO₃ composite particle was obtained between 900° and 950°C while the coexistence of FeO was detected at 1000°C. Transmission electron microscope observation revealed that the composite particle is consisted of nanocrystalline having primary particle size of 35 nm. Lattice parameter of the Fe₃O₄–BaTiO₃ nanocomposite particle was 0.8404 nm that is larger than that of pure Fe₃O₄. Coercivity of the nanocomposite particle (390 Oe) was much larger than that of pure Fe₃O₄ (140 Oe). These results suggest that slight diffusion of Ba into Fe₃O₄ occurred.     

Effect of the t–m transformation morphology and stress distribution around the crack path on the measured toughness of zirconia ceramics: A case study on Ce-TZP/alumina nanocomposite

The t–m transformation zone and related residual stress fields around two types of crack used for toughness measurements, i.e. SEVNB (arrested crack induced by a V-notch) and IF methods (indentation crack induced by a Vickers impression), are reported for a Ce-TZP/Al₂O₃ nanocomposite, in comparison with 3Y-TZP. The fact that Ce-TZP/Al₂O₃ exhibits significant high toughness value on occasions when evaluated by the IF method was determined to be clearly linked to the presence of wide ranged three-dimensional transformation configuration and resulting substantial compressive residual stress fields. In contrast, for 3Y-TZP, transformation behaviors around the two types of crack were quite similar, which proves that 3Y-TZP shows near toughness values for both SEVNB and IF methods.     

Observation of 3‐D Structure of Bubbles in a Fluidized Catalyst Bed

The interface area between the bubble and emulsion phases in a fluidized catalyst bed is one of the important parameters used to analyze and design the fluidized bed reactor. We used a fast‐scanning X‐ray CT system to observe the bubble shape and structure. We then obtained the transient 2‐dimensional cross sectional gas‐phase distribution in a fluidized catalyst bed. Using image‐processing techniques, pseudo 3‐dimensional images of the bubbles were reconstructed. The bubble structure was studied based on the 3‐dimensional images and the previously obtained results in a 2‐dimensional fluidized bed. It was found that the bubble shape was not spherical but complicated, and that the bubbles ascending in a fluidized catalyst bed consisted of some smaller bubbles.     

Effects of Annealing on Dielectric Loss and Microstructure of Aluminum Nitride Ceramics

The effect of annealing on tan δ and microstructures of aluminum nitride (AlN) ceramics were explored. Yttria was added as a sintering additive to AlN powders, and the powders were pressureless-sintered at 1900°C for 2 h in a nitrogen flow atmosphere. In succession to sintering, AlN samples were annealed at 720, 970 and 1210°C for 2 and 4 h. Very low tan δ values between 2.6 and 6.0 × 10⁻⁴ at 28 GHz were obtained when the AlN samples were annealed for 4 h at all the annealing temperatures.     

Fracture Energies of Tape-Cast Silicon Nitride with β-Si3N4 Seed Addition

The fracture energies of the tape-cast silicon nitride with and without 3 wt% rod-like β-Si₃N₄ seed addition were investigated by a chevron-notched-beam technique. The material was doped with Lu₂O₃–SiO₂ as sintering additives for giving rigid grain boundaries and good heat resistance. The seeded and tape-cast silicon nitride has anisotropic microstructure, where the fibrous grains grown from seeds were preferentially aligned parallel to the casting direction. When a stress was applied parallel to the fibrous grain alignment direction, the strength measured at 1500°C was 738 MPa, which was almost the same as room temperature strength 739 MPa. The fracture energy of the tape-cast Si₃N₄ without seed addition was 109 and 454 J/m² at room temperature and 1500°C, respectively. On the contrary, the fracture energy of the seeded and tape-cast Si₃N₄ was 301 and 781 J/m² at room temperature and 1500°C, respectively, when a stress was applied parallel to the fibrous gain alignment. The large fracture energies were attributable primarily to the unidirectional alignment fibrous Si₃N₄ grains.     

Influence of the introduction of flexible alkyl chains on the thermal behavior and mechanical properties of mesogenic epoxy thermosets

A mesogenic epoxy resin (DGETAM) was cured with a series of curing agents having different lengths of long alkyl chain (nBAB, n = 4, 8, 12). Properties of the curings were compared with those of the DGEBA cured with the same curing agents revealing the achievement of a balance between certain levels of thermal properties and excellent mechanical properties. Moreover, some curing systems were prepared with twin mesogenic type epoxy resins (DGEnMA, n = 4, 6, 8, 10, 12) having different lengths of alkyl chain as a flexible spacer and the same curing agents (n′BABs). Combinations of the same concentrations of chemical structures in the basic units of the network structure were applied, and the thermal and mechanical properties of their curing systems were investigated. The fracture energy of each system increased considerably with the increase of the alkyl chain length that adjoins the two mesogenic groups in the epoxy resins. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44244.     

New Approach for Macro Porous RB‐SiC Derived from SiC/Novolac‐type Phenolic Composite

A novel fabrication route to make macroporous silicon carbide (SiC) has been proposed in this study. The route is composed of the following two steps: the fabrication of porous α‐SiC/novolac‐type phenolic composite using hexamethylenetetramine (HMT) as a curing/blowing agent for the novolac monomer and a conventional reaction‐bonded (RB) sintering of the composite. The α‐SiC/novolac‐type phenolic composite was carbonized at 800°C for 2 h in N₂ gas and then reacted with the molten silicon at 1450°C for 30 min under vacuum, resulting in the macroporous RB‐SiC with an open porosity of 48% and relatively large pore size of ~110 μm. The compressive strength of the macroporous RB‐SiC was 113 MPa, which is relatively high compared to those reported for macroporous SiC of equivalent porosities and pore sizes.     

Frictional properties of diamond-like carbon, glassy carbon and nitrides with femtosecond-laser-induced nanostructure

This paper reports macro and micro frictional properties of DLC, TiN, CrN films and GC substrate of which surfaces are nanostructured with femtosecond (fs) laser pulses. The friction coefficient μ of the nanostructured surface was measured at a usual load with a ball-on-disk friction test machine. The results have shown that carbon materials of DLC and GC provide lower values of μ than TiN and CrN, and μ of DLC and TiN measured with a hardened steel ball decreases with an increase of the laser pulse energy. On the other hand, μ of nanostructured surfaces of thin films monotonously increases with an increase in laser pulse energy, which was measured with a micro-scratch test at an ultralight load of 1.5 mN utilizing a diamond tip. The friction coefficient of the GC substrate irradiated at a low fluence around the ablation threshold has shown a lower value than that of the non-irradiated surface.     

Detection of cytochrome P450 substrates by using a small-molecule droplet array on an NADH-immobilized solid surface

Seeing below the surface: A small-molecule droplet array platform on an NADH-immobilized solid surface and a biotinylated acetophenone derivative were developed to identify the substrate candidates for soluble P450 enzymes of interest. This methodology is thought to be easily applicable to other class I P450 systems, including those that use NADPH as cofactor.