The effect of neutron irradiation on the fiber/matrix interphase of silicon carbide composites

Given the good stability of mechanical properties of silicon carbide (SiC) under neutron irradiation, the ultimate irradiation tolerance of SiC composite materials may be limited by the fiber/matrix interphase, which is critically important to the performance of these composites. This study investigates the irradiation stability of pyrolytic carbon (PyC) monolayer and PyC/SiC multilayer interphases by tensile and single fiber push-out test techniques. Neutron irradiation was performed to doses of 0.7-7.7 dpa at temperatures from 380 to 1080 °C. Both interfacial debond shear strength and interfacial friction stress apparently decrease by irradiation, although this is not so dramatic when T_irr < 1000 °C. In contrast, the interfacial shear stresses are most affected by the higher temperature irradiation (>1000 °C). Noteworthy, these irradiation effects depend on the type of interphase material, i.e., for the pyrolytic carbon or multilayer SiC variants studied. In the range of irradiation temperature and dose, the degradation in interfacial shear properties, while measurable, is not of a magnitude to degrade the mechanical performance of the composites. This was observed for both interphase types studied. In particular, the proportional limit tensile stress decreases slightly by irradiation while the tensile fracture strength undergoes very minor change.     

Present Status of the Nd:YAG Thomson Scattering System Development for Time Evolution Measurement of Plasma Profile on Heliotron J

A new high repetition rate Nd:YAG Thomson scattering system is developed for the Heliotron J helical device.A main purpose of installing the new system is the temporal evolution measurement of a plasma profile for improved confinement physics such as the edge transport barrier (H-mode) or the internal transport barrier of the helical plasma.The system has 25 spatial points with ～10mm resolution.Two high repetition Nd:YAG lasers (>550mJ@ 50Hz) realize the measurement of the time evolution of the plasma profile with ～10ms time intervals.Scattered light is collected by a large concave mirror (D=800 mm,f/2.25) with a solid angle of ～100 mstr and transferred to interference filter polychromators by optical fiber bundles in a staircase form.The signal is amplified by newly designed fast preamplifiers with DC and AC output,which reduces the low frequency background noise.The signals are digitized with a multi-event QDC,fast gated integrators.The data acquisition is performed by a VME-based system operated by the CINOS.     

The Association of Cholesterol Uptake and Synthesis with Histology and Genotype in Cortisol-Producing Adenoma (CPA)

Cortisol-producing adenoma (CPA) is composed of clear and compact cells. Clear cells are lipid abundant, and compact ones lipid poor but associated with higher production of steroid hormones. PRKACA mutation (PRKACA mt) in CPA patients was reported to be associated with more pronounced clinical manifestation of Cushing’s syndrome. In this study, we examined the association of histological features and genotypes with cholesterol uptake receptors and synthetic enzymes in 40 CPA cases, and with the quantitative results obtained by gas chromatography-mass spectrometry (GC-MS) analysis in 33 cases to explore their biological and clinical significance. Both cholesterol uptake receptors and synthetic enzymes were more abundant in compact cells. GC-MS analysis demonstrated that the percentage of compact cells was inversely correlated with the concentrations of cholesterol and cholesterol esters, and positively with the activity of cholesterol biosynthesis from cholesterol esters. In addition, hormone-sensitive lipase (HSL), which catalyzes cholesterol biosynthesis from cholesterol esters, tended to be more abundant in compact cells of PRKACA mt CPAs. These results demonstrated that both cholesterol uptake and biosynthesis were more pronounced in compact cells in CPA. In addition, more pronounced HSL expression in compact cells of PRKACA mt CPA could contribute to their more pronounced clinical manifestation.     

Hydrogen‐bonding interaction between poly(ε‐caprolactone) and low‐molecular‐weight amino compounds

The specific interactions between several low‐molecular‐weight diamino compounds and poly(ε‐caprolactone) (PCL) have been investigated by FT‐IR. It was found that PCL and 3,3′‐diaminodiphenylmethane (3,3′‐DADPM) interact through strong intermolecular hydrogen bonds in the blend. Thermal and mechanical properties of PCL/3,3′‐DADPM blends were investigated by DSC and tensile measurements, respectively. The glass transition temperature of the blend increases while both the melting point and the elongation‐at‐break of the blend decrease with the increase of 3,3′‐DADPM content. Besides 3,3′‐DADPM, several other low‐molecular‐weight compounds containing two amino groups, such as o‐phenylenediamine or 1,6‐diaminohexane, were also added into PCL and the corresponding blend systems were investigated by FT‐IR and DSC. The effect of the chemical structure of the additives on the properties of PCL is discussed. © 2001 Society of Chemical Industry     

Reaction joining of SiC ceramics using TiB2-based composites

SiC ceramics were reaction joined in the temperature range of 1450–1800 °C using TiB₂-based composites starting from four types of joining materials, namely Ti–BN, Ti–B₄C, Ti–BN–Al and Ti–B₄C–Si. XRD analysis and microstructure examination were carried out on SiC joints. It is found that the former two joining materials do not yield good bond for SiC ceramics at temperatures up to 1600 °C. However, Ti–BN–Al system results in the connection of SiC substrates at 1450 °C by the formation of TiB₂–AlN composite. Furthermore, nearly dense SiC joints with crack-free interface have been produced from Ti–BN–Al and Ti–B₄C–Si systems at 1800 °C, i.e. joints TBNA80 and TBCS80, whose average bending strengths are measured to be 65 MPa and 142 MPa, respectively. The joining mechanisms involved are also discussed.     

Thermal Stability Threshold for Amyloid Formation in Light Chain Amyloidosis

Light chain (AL) amyloidosis is a devastating disease characterized by amyloid deposits formed by immunoglobulin light chains. Current available treatments involve conventional chemotherapy and autologous stem cell transplant. We have recently concluded a phase III trial comparing these two treatments. AL amyloidosis patients who achieve hematological complete response (CR) do not necessarily achieve organ response regardless of the treatment they received. In order to investigate the possible correlation between amyloid formation kinetics and organ response, we selected AL amyloidosis patients from the trial with kidney involvement and CR after treatment. Six patients were selected and their monoclonal immunoglobulin light chains were characterized. The proteins showed differences in their stability and their kinetics of amyloid formation. A correlation was detected at pH 7.4, showing that less stable proteins are more likely to form amyloid fibrils. AL-T03 is too unstable to form amyloid fibrils at pH 7.4. This protein was found in the only patient in the study that had organ response, suggesting that partially folded species are required for amyloid formation to occur in AL amyloidosis.     

Electric transfer function model of switched reluctance motors and model‐based current control design

This paper presents a current control design for switched reluctance motors (SRMs). The electric transfer characteristic of the motors is studied first. Their transfer function is shown to be expressible by a pure resistive component, which is not constant but varies depending on the motor current and speed. The current control design for SRMs follows the classical design technique used for DC machines, where the zeros of the PI controller cancel the poles of Ls+R. Because the transfer function of SRMs does not have any poles, an I controller is suitable for them. The integral gain should be adjusted in order to compensate the nonlinearity, that is, the variation in the equivalent resistor of the SRMs' transfer function. The values of the integral gain are tuned and tabulated for the motor speed and current. Simulation and experiment demonstrate that the current and speed of the SRMs present good responses without dependence on the motor speed and current. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 173(1): 51–59, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20987     

Effect of chloride ions on leaching rate of chalcopyrite

The effect of chloride on chalcopyrite leaching has been investigated by performing batch leaching tests with three kinds of leaching solutions and using Hiroyoshi’s model, which suggests that a zone of rapid leaching exists between the critical potential (E_c, equilibrium redox potential for the reduction of CuFeS₂ to Cu₂S) and the oxidation potential (E_ox, equilibrium redox potential for the oxidation of Cu₂S). The results of the leaching tests show that the leaching rate in hydrochloric acid solution is the fastest and that the relationship between the Cu leaching rate and oxidation–reduction potential (ORP) follows Hiroyoshi’s model. Thermodynamic calculations indicate that, with an increase in the chloride concentration, the concentration of cuprous ions increases as the chlorocuprate(I) complex ions are formed and the contribution of cuprous ions to the critical potential is greater than that of cupric ions, even though the concentration of cuprous ions is lower than that of cupric ions. This fact suggests that the formation of chlorocuprate(I) ions in a chloride solution may improve the chalcopyrite leaching rate by increasing the critical potential.     

Morphology of CuO through precipitation process under 2.45 GHz microwave irradiation

The morphology of CuO powders formed by a homogeneous precipitation process from aqueous copper precursor complex was investigated. The effect of 2.45 GHz microwave irradiation appeared in the characteristic morphology of the CuO microcrystal with comparison of an ordinal synthesis process. The crystallographic orientation of CuO microcrystals in the particle was examined by HRTEM. Using microwave irradiation, it was demonstrated that the morphology of the particles was kept through the decomposition of the precursor. Also the rapid transformation of a precursor to CuO in aqueous solution under microwave irradiation condition was discussed.     

High‐current lightning discharges in winter

Lightning electric‐field waveforms related to power line faults in winter have been identified. Most of those waveforms appear to be associated with upward lightning discharges with absolute peak currents of over 100 kA. They are quite different from common return‐stroke waveforms, and the lightning discharges which produce these characteristic waveforms are called GC (Ground to Cloud) flashes. These high‐current lightning discharges are distributed around the coastline in different ways depending on their polarities. The spatial distributions of high‐current lightning discharges around Japan are also investigated. It is revealed that the region of Honshu Island along the coastline of the Sea of Japan belongs to the area in which the density of high‐current lightning flashes is the highest in Japan through the year. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 170(1): 8–15, 2010; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20874