Study of pesticide residues in agricultural products for the "Positive List" system

During a 3-year monitoring survey (April 2002-March 2005) of pesticide residues in agricultural products, 592 samples (324 domestic; 268 imported) collected in Hyogo prefecture, Japan were analyzed. The number of pesticides tested increased from 232 in FY 2002 to 323 in FY 2004. The purpose of the study was to clarify the residue status by accumulating information about pesticides detected frequently, to allow effective and efficient regulation under the new "Positive List" legislation to be implemented in FY 2006. Overall, 47% of domestic and 61% of imported samples contained detectable residues and ca. 60% of positive samples contained multiple residues. The limit of quantitation was set at 0.01 microg/g and the limit of detection was 0.001-0.003 microg/ g. Most of the residues were present at low concentrations: 80% of the detections in samples excluding imported citrus fruits were < 0.05 microg/g. More than 5 different pesticides (> 0.01 microg/g) were detected simultaneously in 13 samples. The sum of the ratios of residues to MRLs was calculated as one of the indexes to represent the risk of multiple residues, and they exceeded 100% in 3 imported frozen vegetables; baby kidney bean, spinach, Welsh onion. Samples in violation of the Food Sanitation Law were not found in our survey, but 1.9% of the samples might be in conflict with the new "Positive List" legislation.     

Three-dimensional simulating of concentrator photovoltaic modules using ray trace and equivalent circuit simulators

A 3-dimensional (3D) simulation for a concentrator photovoltaic (CPV) module using a triple-junction solar cell was developed. By connecting ray-trace simulation for an optics model and 3D equivalent circuit simulation for a triple-junction solar cell, the operating characteristics of a CPV module were calculated. By using the 3D simulation, we considered the influence of tracking error on the CPV module. It was found that maximum output power was not correlated with optical efficiency of the optics system and was strongly dependent on fill factor. We can use this total 3D simulation for the evaluation and optimization of CPV modules.     

A Method for Systematic Assessment of Intrinsically Disordered Protein Regions by NMR

Intrinsically disordered proteins (IDPs) that lack stable conformations and are highly flexible have attracted the attention of biologists. Therefore, the development of a systematic method to identify polypeptide regions that are unstructured in solution is important. We have designed an “indirect/reflected” detection system for evaluating the physicochemical properties of IDPs using nuclear magnetic resonance (NMR). This approach employs a “chimeric membrane protein”-based method using the thermostable membrane protein PH0471. This protein contains two domains, a transmembrane helical region and a C-terminal OB (oligonucleotide/oligosaccharide binding)-fold domain (named NfeDC domain), connected by a flexible linker. NMR signals of the OB-fold domain of detergent-solubilized PH0471 are observed because of the flexibility of the linker region. In this study, the linker region was substituted with target IDPs. Fifty-three candidates were selected using the prediction tool POODLE and 35 expression vectors were constructed. Subsequently, we obtained ¹⁵N-labeled chimeric PH0471 proteins with 25 IDPs as linkers. The NMR spectra allowed us to classify IDPs into three categories: flexible, moderately flexible, and inflexible. The inflexible IDPs contain membrane-associating or aggregation-prone sequences. This is the first attempt to use an indirect/reflected NMR method to evaluate IDPs and can verify the predictions derived from our computational tools.     

Densification and Cell Performance of Gadolinium-Doped Ceria (GDC) Electrolyte/NiO–GDC Anode Laminates

A thin film (60 μm thick) of a gadolinium-doped ceria (GDC) electrolyte was prepared by the doctor blade method. This film was laminated with freeze-dried 42 vol% NiO–58 vol% GDC mixed powder and pressed uniaxially or isostatically under a pressure of 294 MPa. This laminate was cosintered at 1100 °–1500 °C in air for 4–12 h. The laminate warped because of the difference in the shrinkage of the electrolyte and electrode during the sintering. A higher shrinkage was measured for the electrode at 1100 °–1200 °C and for the electrolyte at 1300 °–1500 °C. The increase of the thickness of anode was effective in decreasing the warp and in increasing the density of the laminated composite. The maximum electric power density with a SrRuO₃ cathode using 3 vol% H₂O-containing H₂ fuel was 100 mW/cm² at 600 °C and 380 mW/cm² at 800 °C, respectively, for the anode-supported GDC electrolyte with 30 μm thickness.     

Hydrogen and carbon dioxide adsorption with tetra‐n‐butyl ammonium semi‐clathrate hydrates for gas separations

Gas adsorption rates of H₂, CO₂, and H₂‐CO₂ gas mixture (H₂/CO₂ = 3.4) with tetra‐n‐butyl ammonium salt (bromide, chloride, and fluoride) semi‐clathrate hydrate particles were measured at 269 K to assess their properties for gas separation. Equilibrium gas occupancies in the S‐cages of the particles were in order of (high to low) for hexagonal structure‐I, tetragonal structure‐I, and superlattice of cubic structure‐I structures with the maximum fractional occupancy by CO₂ being about 40%. The CO₂ diffusion rate depended on the anion size of the salt, which is attributed to distortion of the S‐cage that is close to the molecular size of CO₂. Simulations of semi‐clathrate hydrate particles with theory showed that H₂/CO₂ selectivities could be as high as 36 (3.0 mol% TBAF) and that selectivities for an ideal membrane (3.3 mol% TBAF) could be >100 (269 K, 0.3–4.5 MPa). Semi‐clathrate hydrates have wide application as separation media for gas mixtures. © 2014 American Institute of Chemical Engineers AIChE J, 61: 992–1003, 2015     

High‐strength regenerated cellulose fibers spun from 1‐butyl‐3‐methylimidazolium chloride solutions

High‐performance regenerated cellulose fibers were prepared from cellulose/1‐butyl‐3‐methylimidazolium chloride (BMIMCl) solutions via dry‐jet wet spinning. The spinnability of the solution was initially evaluated using the maximum winding speed of the solution spinning line under various ambient temperatures and relative humidities in the air gap. The subsequent spinning trials were conducted under various air gap conditions in a water coagulation bath. It was found that low temperature and low relative humidity in the air gap were important to obtain fibers with high tensile strength at a high draw ratio. From a 10 wt % cellulose/BMIMCl solution, regenerated fibers with tensile strength up to 886 MPa were prepared below 22 °C and relative humidity of 50%. High strengthening was also strongly linked with the fixation effect on fibers during washing and drying processes. Furthermore, an effective attempt to prepare higher performance fibers was conducted from a higher polymer concentration solution using a high molecular weight dissolving pulp. Eventually, fibers with a tensile strength of ～1 GPa and Young's modulus over 35 GPa were prepared. These tensile properties were ranked at the highest level for regenerated cellulose fibers prepared by an ionic liquid–based process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45551.     

Numerical analysis of coupled transport and reaction phenomena in an anode-supported flat-tube solid oxide fuel cell

Heat and mass transfer with electrochemical reaction in an anode-supported flat-tube solid oxide fuel cell (FT-SOFC) is studied by means of three-dimensional numerical simulation. The distributions of the reaction fields in the anode-supported FT-SOFC are found to be similar to those in the planar SOFC with co-flow arrangement. However, in comparison with the latter, the concentration and activation overpotentials of the former can be reduced by additional reactant diffusion through the porous rib of the fuel channel. Parametric survey reveals that, for a fixed activation overpotential model, the output voltage can be improved by increasing the pore size of anode, while the cross-sectional geometry has smaller effect on the cell performance. Based on the results of three-dimensional simulation, we also develop a simplified numerical model of anode-supported FT-SOFC, which takes into account the concentration gradients in the thick anode of complex cross-sectional geometry. The simplified model can sufficiently predict the output voltage as well as the distributions of temperature and current density with very low computational cost. Thus, it can be used as a powerful tool for surveying wide range of anode-supported FT-SOFC design parameters.     

Nanostructured supported palladium catalysts—Non-oxidative methane coupling

The Pd on α-Al₂O₃ catalysts with Pd particles in the low nanometer range have been prepared by a sonochemical reduction and a colloidal method, respectively. The two catalysts differ in their particle size, the widths of their particle size distributions and the amount of carbon incorporation in the Pd lattice.The adsorptive properties of the Pd/Al₂O₃ samples are different as a result of the different preparation methods. The methane adsorption capacity of that sample with smaller particles is lower than that of the catalyst with larger particles and the energy of activation is nearly doubled. DRIFTS and TPD results of CO adsorption supported by transmission electron microscopy data indicate that the PdSON catalyst with smaller and more homogeneous particles than PdCOL is highly dispersed which influences the coupling-hydrogenolysis process.The catalytic activity evidenced the formation of different adspecies during methane coupling and chemisorption on both catalysts. During the hydrogenation the carbon adspecies formed mainly methane at low adsorption temperatures. The significant amount of adsorbed methane at 773 K is governed by the highly active coordination unsaturated sites at the surface.     

Corrosion characteristics of reduced activation ferritic steel, JLF-1 (8.92Cr–2W) in molten salts Flibe and Flinak

Static corrosion tests were performed in molten salts, LiF–BeF₂ (Flibe) and LiF–NaF–KF (Flinak), at 500 °C and 600 °C for 1000 h. The purpose is to investigate the corrosion characteristics of reduced activation ferritic steels, JLF-1 (8.92Cr–2W) in the fluids. The concentration of hydrogen fluoride (HF) in the fluids was measured by slurry pH titration method before and after the exposure. The HF concentration determined the fluoridation potential. The corrosion was mainly caused by dissolution of Fe and Cr into the fluids due to fluoridation and/or electrochemical corrosion. Carbon on the surface might be dissolved into the fluids due to the corrosion, and this resulted to the decrease of carbide on the surface. The corrosion depth of the JLF-1 specimen, which was obtained from the weight losses, was 0.637 μm in Flibe at 600 °C and 6.73 μm in Flinak at 600 °C.