Solvothermal synthesis of Hg1−xCdxTe nanostructures—Their structural and optical properties

This article describes a facile, low-cost, solution-phase approach to the large-scale preparation of Hg_1−xCd_xTe nanostructures of different shapes such as nanorods, quantum dots, hexagonal cubes of different sizes and different compositions at a growth temperature of 180 °C using an air stable Te source by solvothermal technique. The XRD spectrum shows that the crystals are cubic in their basic structure and reveals the variation in lattice constant as a function of composition. The size and morphology of the products were examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The formation of irregular shaped particles and few nano-rods in the present synthesis is attributed to the cetyl trimethylammonium bromide (CTAB). The room temperature FTIR absorption and PL studies for a compositon of x = 0.8 gives a band gap of 1.1 eV and a broad emission in NIR region (0.5-0.9 eV) with all bands attributed to surface defects.     

Two-dimensional profiles of fumonisin B1 production by Fusarium moniliforme and Fusarium proliferatum in relation to environmental factors and potential for modelling toxin formation in maize grain

This study has examined in detail the effect of temperature (7-37 degrees C) and water availability (water activity, a(w), 0.89-0.97) on fumonisin B1 (FB1) production by an isolate of Fusarium moniliforme and F. proliferatum on irradiated maize grain after incubation for 28 days. The optimum conditions for F. moniliforme and F. proliferatum were 30 degrees C at 0.97 a(w) and 15 degrees C at 0.97 a(w), respectively. The maximum concentrations were 2861 mg kg(-1) and 17,628 mg kg(-1) dry wt. maize grain, respectively. At marginal a(w)/temperature conditions for growth (e.g. 0.89-0.91 a(w)) no FB1 was detected (<0.1 mg kg(-1)). A high variability was found between replicates for F. moniliforme, but not for F. proliferatum. These data were used to construct two-dimensional diagrams of all the a(w) x temperature conditions favourable for FB1 production for the first time. The data were also subjected to a polynomical regression, which demonstrated that there was a very good fit for the 15-30 degrees C range of temperature and at 0.97 a(w). However, at marginal environmental conditions this was not possible. This suggests that it may be possible to predict within a limited environmental range the potential for significant FB1 production.     

Quantitative characterization of the microstructure of two-phase TiB<Subscript>2</Subscript>+Al<Subscript>2</Subscript>O<Subscript>3</Subscript> ceramics using mean integral curvature

Two-phase TiB₂+Al₂O₃ ceramics with an interconnected or dispersed TiB₂ (minor)-phase microstructure can be produced by variations in processing parameters. A standard method of quantitative characterization of the microstructural bias, i.e., the degree of TiB₂ phase connectivity relative to its dispersion, is necessary to comprehend the mechanism(s) controlling the evolution of microstructure during processing. In this work, techniques derived from stereology were used to quantitatively characterize the microstructural bias on the basis of the connectivity and dispersion of the minor phase (TiB₂), in addition to the size of the TiB₂- and Al₂O₃-phase regions. The mean integral curvature calculated using the area particle-count and area tangent-count methods was determined to quantitatively describe the connectivity of the TiB₂ minor phase around the Al₂O₃ major phase. The results illustrate that, in spite of partial and mixed bias, integral curvature measurements (particularly those based on the area tangent-count method) provide a reliable and reproducible means for quantitative characterization of the two-phase biased microstructure.     

Optimal Design of Level 1 Redundant Water Distribution Networks Considering Nodal Storage

A water distribution network (WDN) is designed to meet time-varying demands with sufficient pressure, taking into consideration an appropriate demand during peak hours. Therefore, a network has inherent redundancy in the sense that under abnormal conditions such as those arising due to pipe breaks or pump failures, deficiency in supply during peak hours can be met through additional supply during off-peak periods. However, this necessitates a storage facility at the consumer end of the network, which is normally available in the form of a sump or an overhead tank in developing countries. Such a storage enables the consumer to store water during the off-peak period and then use it during the peak period. Reliability of a WDN is assessed herein considering nodal storage, and an iterative method is proposed for the optimal design of Level 1 redundant WDNs, i.e., networks that can sustain a single pipe failure without affecting consumer services either in part or in full. The method is illustrated through an example and the designs of a network with and without storage are compared. Provision of a nodal storage is found to reduce the total cost of the network.     

A laboratory study of landfill-leachate transport in soils

Continuous flow experiments were conducted using sand-packed columns to investigate the relative significance of bacterial growth, metal precipitation, and anaerobic gas formation on biologically induced clogging of soils. Natural leachate from a local municipal landfill, amended with acetic acid, was fed to two sand-packed columns operated in upflow mode. Degradation of the influent acetic acid resulted in the production of methane and carbon dioxide, and simultaneous reduction of manganese, iron, and sulphate. Subsequent increase in the influent acetic acid concentration from 1750 to 2900 mg/l, and then to 5100 mg/l, led to rapid increase in the dissolved inorganic carbon, solution pH, and soil-attached biomass concentration at the column inlet, which promoted the precipitation of Mn(2+) and Ca(2+) as carbonate, and Fe(2+) as sulphide. An influent acetic acid concentration of 1750 mg/l decreased the soil's hydraulic conductivity from an initial value of 8.8 x 10(-3)cm/s to approximately 7 x 10(-5)cm/s in the 2-6 cm section of the column. Increasing the influent acetic acid to 5100 mg/l only further decreased the hydraulic conductivity to 3.6 x 10(-5)cm/s; rather, the primary effect was to increase the length of the zone experiencing reduced hydraulic conductivity from 0-6 cm to the entire column. As bioaccumulation was limited to the 0-5 cm section of the column, and the effect of metal precipitation was negligible, the reduction on the deeper sections of the column is attributed to gas flow, which was up to 1440 ml/day. Mathematical modelling shows that biomass accumulation and gas formation were equally significant in reducing the hydraulic conductivity, while metal precipitation contributed only up to 4% of the observed reduction.     

Influence of TCSC on congestion and spot price in electricity market with bilateral contract

This paper presents a quantitative analysis of the effect of TCSC on congestion and spot price in deregulated electricity markets. The paper could also be considered as a comprehensive tutorial on the influence of TCSC in electricity market. A voluntary pool market, where the market participants can trade electricity either via a pool or through bilateral contracts is considered. The electricity market is modeled in an optimal power flow framework with the objective of maximizing the social welfare. In such formulation, the Lagrange operators associated with the equality constraints associated with real power balance give the spot prices of energy at each bus of the system. Studies are carried out with and without TCSC at peak and low loading conditions to capture the influence and to see the effectiveness of TCSC at different loading conditions. The paper further explores the effect of TCSC compensation level on the spot prices and the congestion under varying pool and bilateral loading conditions. A 5-bus test system is used for numerical studies and to showcase the influence of TCSC in an electricity market environment.     

Study of Unrecovered Strain and Critical Stresses in One-Way Shape Memory Nitinol

Unique thermomechanical properties of Nitinol known as shape memory and superelasticity make it applicable for different fields such as biomedical, structural, and aerospace engineering. These unique properties are due to the comparatively large recoverable strain, which is being produced in a martensitic phase transformation. However, under certain ranges of stresses and temperatures, Nitinol wires exhibit unrecovered strain. For cyclic applications, it is important to understand the strain behavior of Nitinol wires. In this study, the unrecovered strain of different Nitinol wire diameters was investigated using constant stress experiment. Uniaxial tensile test has been also performed to find the range of critical stresses. It was observed that the unrecovered strain produced in the first loading-unloading cycle affects the total strain in the subsequent cycles. Moreover, a critical range of stress was found beyond which the unrecovered strain was negligible while the wires heated up to the range of 70-80°C, depending on the wire diameters. The unrecovered strain of wire diameters of 0.19 mm and less was found to be sensitive to the critical stress. On the other hand, for wire diameters bigger than 0.19 mm this connection between the unrecovered strain and the critical stress was not observed for the same range of heating temperature.     

In vitro biocompatibility and antimicrobial activity of wet chemically prepared Ca10−xAgx(PO4)6(OH)2 (0.0 ≤ x ≤ 0.5) hydroxyapatites

Herein, we report the effect of silver ions on the physical, antimicrobial and cytocompatibility properties of wet chemically synthesized silver doped Ca_10?xAg_x(PO₄)₆(OH)₂ (0.0 ≤ x ≤ 0.5) hydroxyapatites (HAp). Silver ions containing HAp exhibit the comparable density, hardness and enhanced antimicrobial properties, in comparison to parent HAp. The optical absorption measurements confirm the presence of silver ions in the doped compositions, which are responsible for as increased antimicrobial property of doped HAp materials for x > 0.3. The cytotoxicity behavior of the doped HAp was evaluated using mouse fibroblast (L929) cell line. The important result has been that doped HAp (x > 0.3) exhibit statistically (significant) lower cell viability in comparison to undoped HAp. However, no difference in cellular functionality on doped HAp surfaces, in terms of cell adhesion and proliferation could be qualitatively observed in reference to undoped HAp. In order to explain the observed antimicrobial and cell viability properties, the in vitro release of Ag⁺ ions has been quantified using Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES) and solubility was measured by weight loss in acetate buffer solution.