Suppression of high-resistance phases of Ni silicide by Se passivation of Si(100)

High-resistance phases of Ni-rich Ni silicide are formed on Si(100) below 400/spl deg/C, while high-resistance phases of Si-rich Ni silicide are formed above 600/spl deg/C. The desired low-resistance NiSi is formed between 400/spl deg/C and 600/spl deg/C. In this paper, the authors report the suppression of high-resistance phases of Ni silicide by passivating the Si(100) surface with a monolayer of Se. A 500-/spl Aring/ Ni on n-type low 10/sup 15/ cm/sup -3/ doped Si(100) wafers, passivated with Se, shows a sheet resistance of /spl sim/2.55 /spl Omega//square upon annealing between 200/spl deg/C and 500/spl deg/C, while the sheet resistance of the 500-/spl Aring/ Ni on identical wafers without Se-passivation jumps to /spl sim/7.92 /spl Omega//square between 300/spl deg/C and 350/spl deg/C. Between 600/spl deg/C and 700/spl deg/C, the sheet resistance of the Se-passivated samples is /spl sim/ 10% lower than that of the control samples. Transmission electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy all confirm that the suppression of high-resistance Ni silicides below 500/spl deg/C is attributed to the suppression of silicidation and above 600/spl deg/C to the delay in Si-rich Ni silicide formation at the Ni/Se-passivated Si(100) interface.     

Thermogravimetric studies of Y1Ba2Cu3O7−x superconductors

The synthesis conditions and oxygen stoichiometry were determined using a thermogravimetric analyser. The kinetics of oxygenation at different temperatures and at different atmospheres were studied. The oxygenation kinetics were found to be sensitive to porosity of the material. The appropriate oxygenation temperature was found to be 400 °C. For oxygenation temperatures below 400 °C, the oxygenation occurs by a nucleation and growth process, whereas for higher temperatures it is diffusion limited.     

151Eu Mössbauer studies on Zn-doped EuBa2Cu3O7−y

¹⁵¹Eu Mössbauer studies have been performed on the compounds EuBa₂(Cu_1?x Zn _x )₃O_7?y withx=0·0, 0·025, 0·05, 0·075 and 0·1. The parent compound, EuBa₂Cu₃O_7?y is superconducting with a transition temperature (T _c ) of 88 K.T _c is depressed as Zn is substituted for Cu in this system and the compounds withx>0·05 do not show superconductivity down to 12 K.¹⁵¹Eu Mössbauer studies at 295 K show a single Mössbauer line in all the compounds (whether superconducting or not) with isomer shift value typical of Eu^{3 +} ion. Further, the isomer shift values are nearly independent ofx and the temperatures down to 10 K. These observations imply that the Cu-O network responsible for superconductivity is very weakly coupled to the Eu sublattice.     

Nickel–Alumina Functionally Graded Materials by Electrophoretic Deposition

Electrophoretic deposition has been used to synthesize nickel–alumina, functionally graded materials from NiO and alumina suspensions in ethanol. Suspension stability and the kinetics of deposition were studied to determine optimum conditions. Deposition starts with an alumina suspension into which a stream of NiO suspension is injected at various flow rates to obtain the desired profiles. The latter were controlled by varying the deposition current density and component flow rate. The green bodies obtained were sintered in Ar/H₂ atmosphere to reduce the NiO to nickel. Various gradation profiles were obtained illustrating the facility of EPD to synthesize continuously graded materials. NiO was used as the precursor for nickel to alleviate settling and rough columnar deposit problems.     

DFT Investigation of Formaldehyde Adsorption Characteristics on MgO Nanotube

The adsorption characteristics of formaldehyde on to MgO nanotube along inner surface, outer surface and terminating end are studied using DFT method with B3LYP/LanL2DZ basis set. The favorable adsorption site is discussed in terms of adsorbed energy which is found to be adsorption of C atom in HCHO with O atom in MgO along inner surface, outer surface and terminating end. The average energy gap variations for all the possible adsorption sites in MgO nanotube are reported. Mulliken population analysis confirms the transfers of electrons from MgO nanotube to HCHO. The conductivity of MgO base material is influenced by the energy gap variation when HCHO is adsorbed on to MgO nanotube. The result of the present study reveals that synthesizing MgO in nanotube form will enhance HCHO sensing characteristics.     

Improved Hydrogen Capping Effect in n-Type Crystalline Silicon Solar Cells by SiN(Si-Rich)/SiN(N-Rich) Stacked Passivation

The effect of hydrogen capping of SiN(Si-rich)/SiN(N-rich) stacks for n-type c-Si solar cells was investigated. Use of a passivation layer consisting of Si-rich SiN with a refractive index (n) of 2.7 and N-rich SiN with a refractive index of 2.1 improved the thermal stability. A single SiN passivation layer with a refractive index of 2.05 resulted in an initial lifetime of 200 μs whereas the layer with a refractive index of 2.7 resulted in a high initial lifetime of 2 ms, but the layer degraded rapidly after firing. A stacked passivation layer with refractive indices of 2.1 and 2.7 had a stable lifetime of 1.5 ms with an implied open-circuit voltage (iV _oc) of 720 mV after firing. The thermally stable passivation mechanism with changing amounts of Si–N and Si–H bonding was analyzed by Fourier-transform infrared (FTIR) spectroscopy. Incorporation of the SiN _x stack layer (2.7 + 2.1) into the passivated rear of n-type Cz silicon screen-printed solar cells resulted in energy conversion efficiency of 19.69%. Improved internal quantum efficiency in the long-wavelength range above 900 nm, with V _oc of 630 mV, is mainly because of superior passivation of the rear surface compared with conventional solar cells.     

Experimental studies on homogeneous charge CI engine fueled with LPG using DEE as an ignition enhancer

Producing and using renewable fuels for transportation is one approach for sustainable energy future for the world. A renewable fuel contributes lesser global climate change. The present work reports on the utilization of liquified petroleum gas (LPG) as a primary fuel with diethyl ether (DEE) as an ignition enhancer in a direct injection diesel engine. LPG has a simpler hydrocarbon structure than conventional fuels. DEE is recently reported as a renewable fuel and to be a low-emission high-quality diesel fuel replacement. A single cylinder, four-stroke, water-cooled naturally aspirated DI diesel engine having rated output of 3.7 kW at 1500 rpm was used for the experiments. Measurements were made to study the performance, combustion and emissions characteristics. From the results, it is observed that, the brake thermal efficiency lower by about 23% at full load with a reduction of about 65% NO emission than the diesel operation. The maximum reduction in smoke and particulate emissions is observed to be about 85% and 89%, respectively, when compared to that of diesel operation, however an increase in CO and HC emissions was observed.     

Experimental investigation of forced convection and desiccant integrated solar dryer

An indirect forced convection and desiccant integrated solar dryer is designed and fabricated to investigate its performance under the hot and humid climatic conditions of Chennai, India. The system consists of a flat plate solar air collector, drying chamber and a desiccant unit. The desiccant unit is designed to hold 75 kg of CaCl₂-based solid desiccant consisting of 60% bentonite, 10% calcium chloride, 20% vermiculite and 10% cement. Drying experiments have been performed for green peas at different air flow rate. The equilibrium moisture content M_e is reached in 14 h at an air flow rate of 0.03 kg/m² s. The system pickup efficiency, specific moisture extraction rate, dimensionless mass loss, mass shrinkage ratio and drying rate are discussed in this paper.