Thermal analysis of the architecture of old and new houses at Ghadames

The study suggests improvements in the design of new houses to conserve energy and enhance indoor thermal comfort. Summer temperature records show that a new house has an average indoor temperature of 35°C with the ambient average 31°C. The traditional house in the old city recorded 28°C for the same period. Winter temperatures in both types of houses were similar (12°C) when not occupied. Architectural features of the two houses were compared to identify those responsible for difference in the thermal performance. Larger exposed surface and window areas, higher overall heat transfer coefficient and weaker thermal coupling with the ground for the new houses seems to contribute to their inferior thermal performance.     

The glass fibre-polymer interface: II—Work of fracture and shear stresses

Pull-out experiments have been carried out on single production fibres under carefully controlled conditions. Four parameters were determined. The interfacial yield stresses, of about 9–14 MPa, were very much smaller than the shear strengths of the bulk polymers in the case of an epoxy, whether post-cured or not, and a non-post-cured polyester. Values for the work of fracture of the interface varied from 140 to 300 Jm^?2, and again were less than those of the polymer. Interface failure sometimes took place in the epoxy rather than at the fibre surface, whereas with the polyester it always took place at the fibre surface. After interface failure, pull-out was governed by friction, with maximum shear stresses of 7–10 MPa for polyester, and 21–34 MPa for epoxy, the higher values being obtained for the post-cured resins. Average frictional shear stresses were sometimes less than a half of the maximum shear stress, indicating that the fibre Poisson's shrinkage was playing an important role in the pull-out process. A silicone release agent reduced the frictional shear stresses to 2·5 MPa, with both resins.     

Location of structural sections from within a highly distorted complex line drawing

Complex and highly distorted line drawings are produced by subjects attempting the Rey Complex Figure test, a clinical test of neuropsychological assessment. However, the marking scheme conventionally employed can be subjective and unreliable. In this paper, the first stages in automating this scoring system are investigated using a robust technique to locate a reduced set of scoring sections and a knowledge-based system that employs spatial metrics and fuzzy approximation techniques. Testing the technique using clinical data produced encouraging results that support the argument that this is a feasible approach for implementing a fully automated system, and that in its current state, can be immediately applied in a semi-automated system.     

Calculation of the molar volume of liquid hydrocarbons

Equations are proposed for calculating the molar volume of liquid hydrocarbons used in production of surfactants. With such data, it will be possible to calculate most of the physicochemical properties of these hydrocarbons to solve many process problems. __________ Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 6, pp. 39–41, Novemmber–December, 2006.     

Use of rheology, dielectric analysis and differential scanning calorimetry for gel time determination of a thermoset

Measurements of gel time of the epoxy system DGEBA(n=0)/m-XDA were carried out using rheometry and dielectric analysis with the objective of checking the validity of Mangion-Johari equation (DEA) and Harran-Laudouard criterium (rheometry) for gel time determination. In this work, gel times obtained by rheometry and dielectric analysis are compared and conversions at gel time calculated. From the experimental results obtained for gel times it was found a reasonable agreement between the two techniques that lead to gel conversion values very close to those obtained using Flory equation.     

Modelling and analysis of 3-D arrangements of particles by point processes with examples of application to biological data obtained by confocal scanning light microscopy

Within the concept of point processes, a review is presented of quantities which can be used in studies of three-dimensional (3-D) aggregates of particles. Suitable characteristics and estimators are given for both unmarked and marked point processes. To demonstrate the feasibility of such quantitative approaches, an application in histology, dealing with 3-D arrangements of cell nuclei in rat liver, is described. Using a confocal scanning light microscope, 3-D images are recorded and image analysis used to obtain the coordinates of the centroid, together with the volume and DNA content, of each cell nucleus. Examples of results are given, using both unmarked and marked point processes. In the latter case, cell type, nuclear volume and ploidy group are suitable marks.     

Developing and fully developed turbulent flow of drag reducing fluids in an annular duct

Velocity profiles for the inner and outer flow regions of annuli are proposed for the turbulent flow of drag reducing fluids. Theoretical expressions for friction factors are developed. From the shear stress equations and the velocity profiles, estimates for the entrance lengths are given.