A new modeling approach for circuit‐field‐coupled time‐stepping electromagnetic analysis of saturated interior permanent magnet synchronous motors

This paper proposes a new modeling approach for circuit‐field‐coupled time‐stepping electromagnetic analysis of a saturated interior permanent magnet synchronous motor (IPMSM). To predict the drive performance quickly, the proposed approach consists of a dynamic simulator based on a new analytical model of the d‐ and q‐axis magnetization characteristics (λ‐i_d‐i_q‐θ). The model can take into account not only cross‐saturation but also the harmonics of the inductance distributions and EMF waveforms. The validity of the model is verified from suitable simulation results for the instantaneous current and torque waveforms of the IPMSM. The proposed analysis leads to a dramatic reduction in the computation time compared to circuit‐field‐coupled time‐stepping FEA, while maintaining analytical accuracy. The effectiveness of the proposed method is experimentally verified using a 10‐kW, 15,000‐rpm concentrated‐winding IPM motor. © 2010 Wiley Periodicals, Inc. Electr Eng Jpn, 174(1): 49–58, 2011; Published online in Wiley Online Library (wileyonlinelibrary.com). DOI 10.1002/eej.21024     

Dielectric Dispersion of Polycrystalline Aluminum Nitride at Microwave Frequencies

Complex permittivity of polycrystalline AlN was measured over the frequency range 100 MHz to 13 GHz using reflection coefficient and cavity resonator methods. Dielectric relaxation peaks of loss tangent were observed in the frequency range 200 MHz to 3 GHz. The maximum value of loss tangent was ∼200 × 10⁻⁴. Relative permittivities decreased by ∼4% with increased frequency at the region of relaxation peaks. It was shown that these dispersion frequencies were inversely proportional to the grain sizes of AlN and independent of purities and processes. Model calculations for elastic vibration of a single-crystal grain of AlN were performed to investigate the origin of the dielectric dispersion due to piezoelectric effect. The calculated results of elastic sphere and 14-faced-polyhedron models showed a good quantitative agreement with the observed dispersion frequencies, which suggested that the dispersion was due to a piezoelectric vibration of a single grain of AlN ceramics at microwave frequencies.     

Pore structure of carbons coated on ceramic particles

Pore structure of carbon coated on ceramic particles by carbonization of precursor in a powder mixture at 900 °C was studied by focusing on the effects of substrate ceramics (MgO, TiO₂ and various phases of Al₂O₃) and of carbon precursor (poly(vinyl alcohol) (PVA), poly(ethylene terephthalate) (PET) and hydroxyl propyl cellulose (HPC)). By dissolving substrate MgO particles, carbon coated was found to have a high BET surface area, more than 1000 m²/g, which was almost the same as the value estimated from apparent surface area measured on carbon-coated MgO particles under the assumption of zero surface area of the substrate. The carbon separated was found to be rich in micropores from the analyses by DFT method and α_s plot. The dependence of the BET surface area on the amount of carbon coated on TiO₂ with a high surface area was the same for three carbon precursors, although the carbon yields from the precursors were slightly different. Porous Al₂O₃ substrates, γ-Al₂O₃as-received and that formed from Al(OH)₃ during carbonization, gave a high BET surface area, but dense Al₂O₃, α-Al₂O₃, gave a low surface area.     

粘弹性流体旋转流实验研究

利用粒子图像测速仪(PIV)对圆筒形容器内有自由表面变形的粘弹性流体旋转流动进行了实验研究.旋转流动由等速旋转的容器底面来驱动.实验工质为CTAC(十六烷基三甲基氯化铵界面活性剂)水溶液.测量了水、40×10-6、60×10-6和200×10-6CTAC水溶液在弗鲁德数为2.59至16.3范围内的旋转流动.PIV用来测量子午面内的二次流场,并从PIV图像中抽取自由面高度.结果表明在相似的弗鲁德数下,相比于水流CTAC水溶液旋转流动自由表面中心处的凹陷深度降低,随着溶液浓度或粘弹性升高,子午面内右上角的惯性涡被压缩且强度变得越来越弱.通过与水流动比较并做力平衡分析,定量估算了CTAC水溶液的第一正应力差或弱粘弹性.     

Self-dissolving micropile array tips for percutaneous administration of insulin

Two kinds of insulin were loaded into self-dissolving micropile array tip (following tip). Fully-loaded tip (f-tip) and partially-loaded tip (p-tip) were prepared using chondroitin sulfate for the percutaneous administration of insulin. One hundred micropiles were constructed on a 1.0 × 1.0 cm tip. The mean length of the micropile in a tip were 483.4 ± 4.7 μm for the f-tip and 492.6 ± 2.4 μm for the p-tip. The insulin content of the p-tip was 28.5% of that of the f-tip. The pharmacological efficiency of insulin loaded tip was evaluated in rat experiments by measuring their hypoglycemic effects. The maximum hypoglycemic effect of insulin was observed at 1.7 ± 0.2 h for the f-tip and 1.5 ± 0.2 h for the p-tip. Good dose-dependency was observed for the plasma glucose level vs. time curves. These results suggest the usefulness of p-tip as a percutaneous DDS of insulin.     

High‐brightness electron sources for a next‐generation light source based on an energy recovery linac

A high‐brightness electron source of ultrasmall emittance and high average current is one of the most important components for next‐generation light sources based on an energy‐recovery linac (ERL). Such a high‐brightness electron source can be realized by a DC photocathode gun driven by laser pulses tailored in the temporal and spatial dimensions. We propose a novel photocathode based on a quantum cascade laser (QCL). Since the ultrafast response of photoelectron emission from QCL is compatible with the tailored laser pulses, it is a candidate electron source for ERLs. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 177(3): 46–53, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21154     

Impact of the Coulomb interaction on nano-scale silicon device characteristics

Monte Carlo simulations coupled self-consistently with the three-dimensional Poisson equation are carried out under the double-gate MOSFET structures. The Coulomb force experienced by an electron inside the device is directly evaluated by performing the Monte Carlo simulations with or without the full Coulomb interaction and the Coulomb force on the channel electron corresponding to plasmon excitations is clarified. It is pointed out that the consistency of the boundary condition is achieved only if the long-range Coulomb interaction is properly taken into account, and this is crucial for predicting reliable device characteristics in ultra-small devices. The drain current and transconductance are greatly reduced if the self-consistent potential fluctuations are taken into account.     

Waste management strategy focused on maintenance,storage and recycling

Waste is generated at the moment when the operation of a fusion reactor is halted and maintenance is started for periodic replacement of blanket modules and divertor. Used blanket and divertor need to be replaced shortly after the shutdown for high plant availability, as long as high surface dose rate and decay heat of the blanket and divertor can be handled. In this sense, nuclear characteristics of the blanket and divertor need to be understood for a reasonable maintenance scheme. For the purpose, neutronic calculations were carried out on the blanket and divertor using a THIDA-2 code with FENDL-2.0. For a SlimCS DEMO reactor, the calculated decay heat for each 1/12-sector was as high as 5 MW just after the shutdown and 0.3 MW one month later. For the maintenance, a cooled shielding structure (CSS) was proposed to remove the decay heat and to shield gamma-rays from the sector. When maintenance is done one month after the shutdown, the sector temperature is maintained to be 550 °C or lower with the cooling by the CSS of 50 °C. In order to avoid tritium release from the sector during the maintenance, a cask should be used to transport the sector. For efficient use of resources, breeding and neutron multiplying materials should be reused or recycled. A possible strategy for reuse or recycle is also presented.     

Reduction of system matrices of planar beam in ANCF by component mode synthesis method

A method of reducing the system matrices of a planar flexible beam described by an absolute nodal coordinate formulation (ANCF) is presented. In this method, we focus that the bending stiffness matrix expressed by adopting a continuum mechanics approach to the ANCF beam element is constant when the axial strain is not very large. This feature allows to apply the Craig–Bampton method to the equation of motion that is composed of the independent coordinates when the constraint forces are eliminated. Four numerical examples that compare the proposed method and the conventional ANCF are demonstrated to verify the performance and accuracy of the proposed method. From these examples, it is verified that the proposed method can describe the large deformation effects such as dynamic stiffening due to the centrifugal force, as well as the conventional ANCF does. The use of this method also reduces the computing time, while maintaining an acceptable degree of accuracy for the expression characteristics of the conventional ANCF when the modal truncation number is adequately employed. This reduction in CPU time particularly pronounced in the case of a large element number and small modal truncation number; the reduction can be verified not only in the case of small deformation but also in the case of a fair bit large deformation.     

Numerical investigation of zoomable holographic projection without a zoom lens

Holographic projection is for laser displays and has the merits of being aberration free, producing high‐contrast images, having the ability of color reconstruction with one spatial light modulator, and so on. In this paper, we propose a zoomable holographic projection without using a zoom lens and verify the proposed method by using numerical simulation. Although such a system can be readily realized to use the features of holography, which is capable of recording a large image exceeding the hologram size, the required calculation is very time consuming. For acceleration, we used shifted Fresnel diffraction for setting different sampling rates on a hologram and projected image. The proposed method can project any zoom‐in and zoom‐out image between zeroth‐order and first‐order lights, and the processing time and required memory for the zoom are constant.