Direct conversion receiver for radio communication systems

Direct conversion receiver (DCR) architecture, which has introduced the zero intermediate frequency (IF) approach, supports efficient wireless handset designs with a high level of integration. Transmission over wireless channels is subject to time dispersion due to multipath propagation and frequency dispersion due to Doppler effect, the design of wireless receivers are tremendously important in supporting reliable communication links. With wireless technology growing, the choice of optimal wireless receiver architecture that supports monolithic integration without performance degradation becomes an important dimension in modern handset design. The increasing demand for mobile terminals with smaller physical dimensions has led to the investigation of DCR, which supports single chip and multinode designs. Since DCR is a promising architecture for fourth generation mobile terminals, it is important to note that implementation of a certain dc offset technique does not compromise the benefits of low complexity receiver design.     

A novel silicon Schottky diode for NLTL applications

The design and simulation of a novel silicon Schottky diode for nonlinear transmission line (NLTL) applications is discussed in this paper. The Schottky diode was fabricated on a novel silicon-on-silicide-on-insulator (SSOI) substrate for minimized series resistance. Ion implantation technology was used as a low-cost alternative to molecular beam epitaxy to approximate the delta (/spl delta/) doping profile, which results in strong nonlinear CV characteristics. The equivalent circuit model of the Schottky diode under reverse bias conditions was extracted from the S-parameter measurement performed on the diode. The measured CV characteristics show strong nonlinearity, the junction capacitance varies from 182 to 47.5 fF as the reverse bias voltage is varied from 0 to -5 V. A parasitic inductance of 40 pH was measured for the silicon Schottky diode, which is much smaller than a comparable sized GaAs Schottky diode. This small inductance is an advantage for the silicon Schottky diode offering improvement in the silicon NLTL performance.     

Pyramid collaborative filtering technique for an intelligent autonomous guide agent

This article presents an autonomous guide agent that can observe a community of learners on the web, interpret the learners' inputs, and then assess their sharing. The goal of this agent is to find a reliable helper (tutor or other learner) to assist a learner in solving his task. Despite the growing number of Internet users, the ability to find helpers is still a challenging and important problem. Although helpers could have much useful information about courses to be taught, many learners fail to understand their presentations. For that, the agent must be able to deal autonomously with the following challenges: Do helpers have information that the learners need? Will helpers present information that learners can understand? And can we guarantee that these helpers will collaborate effectively with learners? We have developed a new filtering framework, called a pyramid collaborative filtering model, to whittle the number of helpers down to just one. We have proposed four levels for the pyramid. Moving from one level to another depends on three filtering techniques: domain model filtering, user model filtering, and credibility model filtering. A new technique is filtering according to helpers' credibilities. Our experiments show that this method greatly improves filtering effectiveness. © 2007 Wiley Periodicals, Inc. Int J Int Syst 22: 1065–1082, 2007.     

CONTEXTUALIZING LEARNING OBJECTS USING ONTOLOGIES

Educational research over the past three years has intensified such that the context of learning resources needs to be properly modeled. Many researchers have described and even mandated the use of ontologies in the research being conducted, yet the process of actually connecting one or more ontologies to a learning object has not been extensively discussed. This paper describes a practical model for associating multiple ontologies with learning objects while making full use of the IEEE LOM specification. The model categorizes these ontologies according to five major categories of context based on the most popular fields of study actively being pursued by the educational research community: Thematic context, Pedagogical context, Learner context, Organizational context, and Historical/Statistical context.     

A hybrid technique of modeling of cracks using displacement discontinuity and direct boundary element method

A hybrid technique to model two dimensional fracture problems which makes use of displacement discontinuity and direct boundary element method is presented. Direct boundary element method is used to model the finite domain of the body, while displacement discontinuity elements are utilized to represent the cracks. Thus the advantages of the component methods are effectively combined. This method has been implemented in a computer program and numerical results which show the accuracy of the present method are presented. The cases of bodies containing edge cracks as well as multiple cracks are considered. A direct method and an iterative technique are described. The present hybrid method is most suitable for modeling problems involving crack propagation.     

Effect of cooking on the chemical composition of lentils,rice and their blend (Koshary)

Lentils, rice and their blend (Koshary) were cooked by traditional Egyptian methods. Cooking resulted in slight changes in the total nitrogen, as well as in the non-protein nitrogen (NPN), ether extract and crude fibre of the three products, compared with raw grains. In contrast, significant decreases were found in the mineral elements, indicating losses through leaching, on washing and cooking. The mineral composition of lentils' cooking liquor confirmed this.     

Window materials for high power gyrotron

The room temperature application of sapphire as window material at higher frequencies is not feasible since its absorption coefficient increases almost linearly with increasing frequency in the millimeter wavelength region. At cryogenic temperature the absorption coefficient value decreases only by a few factors (factor of 2 to 3) in the 90 – 200 GHz region. The earlier reported temperature squared dependence (decrease) in the absorption coefficient or the loss tangent value is totally absent in our broad band continuous wave data we are reporting here (at 6.5 K, 35K, 77K and 300K) and one we reported at conferences earlier. Our results are verified by another technique. We utilize our precision millimeter wave dispersive Fourier transform spectroscopic techniques at room temperature and at cryogenic temperatures The extra high resistivity single crystal compensated silicon is no doubt the lowest loss material available at room temperature in the entire millimeter wavelength region At higher millimeter wave frequencies an extra high resistivity silicon window or an window made with extra high resistivity silicon coated with diamond film would certainly make a better candidate in the future. A single free standing synthetic diamond window seems to have higher absorption coefficient values at millimeter wavelength region at this time although it is claimed that it possesses good mechanical strength and higher thermal conductivity characteristics. It certainly does not rule out the use of diamond film on a single crystal high resistivity silicon to improve its mechanical strength and thermal conductivity     

The electrical properties of post-deposition annealed and as-deposited In-doped CdTe thin films

The electrical properties of CdTe thin film have been studied and discussed, including, the conduction mechanism, and the effect of temperature and indium doping on the current passing through the CdTe film and hence on the film conductivity. It is observed that the CdTe film is of the modified Poole–Frenkel conduction mechanism and the resistivity of the film can be lowered by more than one order of magnitude due to indium doping.     

An incentive scheduling mechanism for peer-to-peer video streaming

P2P video streaming networks are found as a scalable solution and an alternative for traditional client–server based video streaming over the Internet. One of the significant issues affecting the success of any P2P streaming network is cooperation between peers. Practical observations have proved the prevalence of free riders in P2P networks that degrade their performance. To solve this problem, using incentive mechanisms, which encourage peers to contribute more in the network, is necessary. In this paper, we designed and proposed a distributed and scalable incentive mechanism for mesh based P2P video streaming networks. In the proposed approach the contribution of the peers is measured and maintained in a distributed fashion. Furthermore, we proposed an incentive sending side scheduler in which peers are served based on their contribution in the network. Our simulation evaluations show the efficiency of the proposed approach in improving the overall perceived video quality by the non-free rider nodes and consequently in the whole network.     

File size models for shared content over the BitTorrent Peer-to-Peer network

Peer-to-Peer (P2P) traffic has increased rapidly over the past few years, with file sharing providing the main drive behind such traffic. In this work we perform a measurement study of the content shared over the popular BitTorrent P2P file sharing network. We mathematically model the file size distributions of shared files after categorizing them into Audio, Video, Archive and CD image classes. For each of these categories we look into the most popular shared file formats and investigate their file size statistics. This provides an important milestone to building a realistic simulation framework for P2P systems, and for future analytical modeling of P2P networks.