Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

Vapor pressure and thermodynamic functions of TeI<Subscript>4</Subscript> and its decomposition products

Using a flow method, we have measured the vapor pressure of tellurium tetraiodide, an attractive reagent for chemical vapor deposition technology. The results, combined with earlier tensimetric data, have been used to evaluate the basic thermodynamic functions of TeI₄ and its thermolysis products.     

FATIGUE DAMAGE IN 1045 STEEL UNDER VARIABLE AMPLITUDE BIAXIAL LOADING

Abstract— During constant amplitude loading, two different types of crack systems have been reported In the high cycle fatigue (HCF) region, cracks nucleate on a small number of maxium shear strain amplitude planes One of these cracks becomes a dominant crack and leads to failure of the specimen In the low cycle fatigue (LCF) region, equally developed microcracks are observed over the entire gage section and grow during the majority of the life. The failure is due to a linking in which the microcracks join up during the last few cycles of the fatigue life.
To investigate the interaction of these two types of crack systems in biaxial fatigue, experiments were performed on thin-wall tubular specimens in tension, torsion and combined tension-torsion loading The test program included step loading and block loading in which two equivalent strain amplitudes were employed. One of the equivalent strain amplitudes is in the HCF region and the other was in the LCF region
Fatigue lives were predicted from constant amplitude damage curves when a single crack system dominated the fatigue process Two competitive crack systems were sometimes developed on the maximum shear strain amplitude planes in a single specimen under block loading This resulted in a conservative prediction of the fatigue life.     

AN ASSESSMENT OF CRACK CLOSURE AND THE EXTENT OF THE SHORT CRACK REGIME IN Q1N (HY80) STEEL

Abstract— The paper addresses some aspects of the differences in fatigue crack growth rate behaviour and threshold values obtained for long through-cracks, short through-cracks and surface cracks. Attention is focused on plasticity induced closure in the wake behind the growing crack tip. For long cracks at high K _max, closure is found to depend in a linear manner on K _max, i.e. K _op, increases with the size of the monotonic plastic zone. Closure increases at low δ K and this is primarily a consequence of the load shedding procedure. If short through-cracks are prepared by machining specimens containing long cracks, a substantial part of the plastic wake is removed and this can produce marked effects on the closure contribution during subsequent growth. The length of crack "closed" in a long crack threshold test was found to be of the order of 1 mm. Cracks less than this length exhibited "short crack" behaviour: greater than this length, they behaved as "long cracks", with plastic wake effects apparently fully operative. Small surface cracks exhibit "long crack" behaviour at lengths as short as 0.2 mm and reasons for this are discussed.     

Fuzzy Learning of Talbot Effect Guides Optimal Mask Design for Proximity Field Nanopatterning Lithography

Processing methods used in photonics and nanotechnology possess many limitations restricting their application areas such as high cost, inability to produce fine details, problems with scalability, and long processing time. Proximity field nanopatterning is a lithography method which surpasses these limitations. By using interference patterns produced by a two-dimensional phase mask, the technique is able to generate a submicron detailed exposure on a millimeter-size slab of light sensitive photopolymer, which is then developed like a photographic plate to reveal three-dimensional interference patterns from the phase mask. While it is possible to use simulations to obtain the interference patterns produced by a phase mask, realizing the mask dimensions necessary for producing a desired interference pattern is analytically challenging due to the intricacies of light interactions involved in producing the final interference pattern. An alternative method is to iteratively optimize the phase mask until the interference patterns obtained converge to the desired pattern. However, depending on the optimization technique used, one either risks a significant probability of failure or requires a prohibitive number of iterations. We argue that an optimization technique that is to take advantage of the physics of the problem using machine learning methods (here fuzzy learning) can lead to competent mask design. This technique is described in this letter.     

Modification of platinum surfaces by spontaneous deposition: Methanol oxidation electrocatalysis

The presence of a second metal on platinum surfaces affects the performance of methanol oxidation. However, most of the electrocatalytic reactions are studied by using electrochemically deposited platinum alloys, but in the case of spontaneous deposition the situation is not so clear since the surface distribution, stability and morphology are usually not well documented. The formation of surface decorated samples on mono- and poly-crystalline platinum is followed by electrochemical and spectroscopic techniques and analysis of their performance towards methanol adsorption and oxidation compared with that on pure platinum. Pt/Sn and Pt/Ru are of special interest because of their well-known performance in methanol fuel cells. Methanol oxidation on Pt(111)/Ru, Pt(111)/Sn and Pt(111) shows that ruthenium is the only one able to promote the reaction since the simultaneous dissolution of tin occurs and competes with the process of interest. The in situ infrared spectroscopy is used to compare methanol oxidation on Pt(111)/Ru and Pt(111) in acid media using p-polarized light. The formation of bridge bound carbon monoxide is inhibited in the presence of ruthenium ad-species, whereas on Pt(111) the three adsorption configurations are observed. Linear sweep polarization curves and Tafel slopes (calculated from steady state potentiostatic plots) for methanol oxidation are compared on polycrystalline surfaces modified by tin or ruthenium at different coverages. There is almost no change in the Tafel slopes due to the presence of the foreign metal except for Pt/Ru, where a 0.09 V decade⁻¹ slope was calculated below 0.55 V due to hydroxyl adsorbates on ruthenium islands. The anodic stripping of methanol residues on the three surfaces indicates a lower amount of carbon monoxide-type adsorbates on Pt/Ru, and the simultaneous tin dissolution process leading to residues oxidation on Pt/Sn electrodes.     

Study of a BGO calorimeter using electron and hadron beams from 1 to 50 GeV

A calorimeter of 25 bismuth germanate (BGO) crystals equipped with silicon photodiode readout has been tested at the CERN SPS in the energy range 1–50 GeV. The response for electrons has been shown to be linear in this energy range and the rms resolution obtained ( ) is approximately 1%, for E > 4 GeV. The electron/pion separation was found to be better than 1:500 in the energy range 1–20 GeV. Data on lateral and longitudinal shower development were compared with the results of a Monte Carlo simulation using the SLAC-EGS program and found to be in good agreement.     

The elastic potential of a deformable anisotropic body

Based on the criteria of safety of the spherical portion of the deformation stresses and for the work of deformation on the limiting condition of a material a separation is made of the elastic energy of deformation of an anisotropic body. It is shown that in the general case of loading the components of the spherical portion of the stresses and strains are not equal to one third of their first invariants. The values of these components, as for the values of the deviator portion of the elastic potential, depend upon the stressed and strained state and the loading direction (deformation).Translated from Problemy Prochnosti, No. 3, pp. 38–40, March, 1991.