Effect of anisotropy of tin on thermomechanical behavior of solder joints

Properties of body centered tetragonal tin are highly anisotropic. As a consequence large stresses can develop at the tin grain boundaries due to coefficient of thermal expansion mismatch during temperature excursions. A modeling approach to evaluate the 3D stress states that develop at grain boundaries during thermomechanical fatigue in tin-based solder is presented. Development of significant amounts of stresses in the plane of the grain boundary can cause grain-boundary sliding and surface-relief effects, while those normal to the grain boundary can cause grain-boundary decohesion and cracking.     

The Influence and Interpretation of Surface Parameters for Wetting Transitions in Ternary Mixtures

Starting from a microscopic Hamiltonian defined on a semi-infinite cubic lattice, and employing a mean-field approximation, the surface parameters relevant for wetting in confined ternary mixtures are derived. These are found in terms of the microscopic coupling constants, and yield a physical interpretation of their origins. In comparison with the standard expression for the surface free-energy density, several new terms arising from the derivation are identified. The influence of the surface parameters on a predicted unbinding transition in a mixture of oil, water, and amphiphile demonstrate that existing results are robust to the addition of the extra surface terms.     

Narrow-band correction of the residual amplitude modulation in frequency-modulation spectroscopy

We have developed a narrow-band controller in the MHz range, based on a field-programmable gate array. It is used to control the probe beam intensity in frequency-modulated spectroscopy experiments with an acoustooptic modulator. The residual amplitude modulation at the modulation frequency (2.5 MHz) is reduced by 50 dB. The first-harmonic detection of the signals is operated in saturation spectroscopy of I/sub 2/ at 514.5 nm and 501.7 nm. A reduction of the background noise and a large increase in the signal-to-noise ratio are obtained.     

Motive Force in a Complex Model of Mass Transfer

Relations for determining a motive force in a complex model of mass transfer as applied to concurrent, countercurrent, and cross motion of the vapor and liquid phases have been introduced. These forces have been compared for different forms of organization of the flow, and their comparison with similar quantities from the known Murphree and Hausen models is presented.     

Experimental characterisation of the drying effect on uniaxial mechanical behaviour of mortar

The main objective of this present study was to evaluate, for a standard mortar, the drying effect on its mechanical behaviour. Numerous uniaxial compression tests were thus performed with loading-unloading cycles. They were carried out on different samples previously preserved under various conditions of conservation: preserved from desiccation, air drying and rapid drying at 60°C. The obtained results showed significant influences of these conditions on the material behaviour (increase in strength, decrease in Young's modulus and Poisson's ratio) and the necessity of taking into account the coupling effects between mechanical—poromechanical behaviours and drying.     

Trajectory control of incompletely restrained parallel-wire-suspended mechanism based on inverse dynamics

This paper discusses parallel wire mechanisms where an end-effector of the mechanism is suspended by multiple wires. The mechanisms enable not only three-dimensional (3-D) positioning but also 3-D orienting of the end-effector, unlike typical wire suspension-type mechanisms such as overhead crane. To discuss the parallel-wire-suspended mechanisms generally, two forms of basic dynamic equations are presented. Then the parallel wire mechanisms are classified into two types based on the basic equations. Dynamical properties of the two types of wire-suspended positioning mechanism are discussed. In this paper, one of the wire-suspended mechanism, incompletely restrained-type parallel wire mechanism, is mainly discussed on its inverse dynamics problem and its trajectory control problem. The inverse dynamics problem for the incompletely restrained-type mechanism plays an important role on its control problem, because the mechanism has low stiffness based on incomplete constraints on the suspended object which is governed by its dynamics. The paper proposes an antisway control method for the suspended object. In the method, the inverse dynamics calculation is used for nonlinear dynamics compensation to control the suspended object of the incompletely restrained parallel wire mechanism.     

NEXUS — Resilient Intelligent Middleware

Service-oriented computing is the latest software paradigm brought about by the computing revolution. The different viewpoint and granularity of software components used in technologies based on the service-oriented architecture paradigm, compared to traditional object-oriented methodologies makes them better suited to many of the efforts that are being made in the pervasive and ubiquitous computing world. In the NEXUS project we are seeking ways of fusing the SOA and pervasive computing paradigms in order to build intelligent, robust and resilient networks connecting dynamic islands of service resources.     

Low Temperature Physics at the Laboratoire National des Champs Magnétiques Pulsés in Toulouse

An overview over past and present activities and future developments at the Toulouse pulsed magnetic field facility is given, both as far as technical developments of the infrastructure, as well as low temperature physics performed at the LNCMP are concerned.     

Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.