Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Influence of inhibitor addition on the corrosion protection performance of sol–gel coatings on AA2024

Sol–gel films are actively investigated during the last decade as possible candidates for environmentally friendly pre-treatments. However, the important drawback in this case is the lack of active corrosion protection and self-healing ability.     

Chemical changes in polyvinyl fluoride during the process of fibre-spinning

Conclusions The change in some properties of polyvinyl fluoride during the process of fibre spinning has been investigated.It has been found that during the process of converting PVF powder into fibre, the degree of polymer crystallinity plus its resistance to thermal and thermooxidative degradation is increased; depending on the spinning regime, the densities and physicomechanical properties of PVF fibres are different.Translated from Khimicheskie Volokna, No. 4, pp. 34–35, July–August, 1984.     

Retention of Escherichia coli in municipal sewage by means of planted soil filters in two-stage pilot plant systems.

Different types of constructed wetlands in a pilot-plant system were fed with identical municipal waste water to compare the sanitisation process in two-stage systems. With combinations of a vertical and a horizontal flow filter an E. coli reduction of 5 log10 with an E. coli influent concentration of 10(7) MPN/100 ml was achieved. Using different filter materials in each stage the total performance of the two-stage system was independent from the sequence of these materials. However, using coarser filter material in the first stage makes the filter less prone to clogging and is thus the preferential option with regard to operational reliability.     

Comfort limits for asymmetric thermal radiation

Groups of 32 and 16 subjects of both sexes were exposed in an environmental chamber to radiant asymmetry caused by a cool wall, a warm wall, and a cool ceiling. Each subject was tested individually while seated and clothed at 0.6 clo. During each 3.5-hour experiment the subject was exposed to six radiant temperature asymmetries. He was asked whether and where he experienced any local cool or warm sensation, and whether it was felt to be uncomfortable. During the entire experiment he was kept thermally neutral by changing the air temperature according to his wishes.For cool walls, warm walls, and cool ceilings curves have been established showing the percentage of dissatisfied subjects as a function of the radiant asymmetry. Radiant asymmetry at a warm wall caused less discomfort than a cool wall. A cool ceiling caused less discomfort than a warm ceiling. Accepting that 5% of the subjects may feel uncomfortable. a radiant temperature asymmetry of 10°C is allowable at a cool wall, 23°C at a warm wall, and 14°C under a cool ceiling. A previous study showed that 4°C is allowable under a warm ceiling. Radiant asymmetry had no significant impact on the operative temperatures preferred by the subjects. No significant differences were observed between the responses of men and women exposed to radiant asymmetry.     

Near-resonance oscillations of a nonsymmetric nonlinear system with a crack

The Malkin method, which was developed to construct a single unique resonance solution of nonlinear equations, is generalized for the case of the derivation of all stationary solutions in the near-resonance zone, and also for transient oscillations.Kiev Polytechnic Institute. Translated from Problemy Prochnosti, No. 10, pp. 108–112, October, 1989.     

An integrated system to remote monitor and control anaerobic wastewater treatment plants through the internet.

The TELEMAC project brings new methodologies from the Information and Science Technologies field to the world of water treatment. TELEMAC offers an advanced remote management system which adapts to most of the anaerobic wastewater treatment plants that do not benefit from a local expert in wastewater treatment. The TELEMAC system takes advantage of new sensors to better monitor the process dynamics and to run automatic controllers that stabilise the treatment plant, meet the depollution requirements and provide a biogas quality suitable for cogeneration. If the automatic system detects a failure which cannot be solved automatically or locally by a technician, then an expert from the TELEMAC Control Centre is contacted via the internet and manages the problem.     

Solution of Helmholtz equation by Trefftz method

The application of the Trefftz method for calculating wave forces on offshore structures is presented. Indirect and direct formulations using complete and non-singular systems of Trefftz functions for the Helmholtz equation are posed in this paper. An effective technique using different interpolation functions for the velocity potential and wave force are suggested to improve the computational accuracy of the wave force. The numerical examples show that the present method is highly efficient and accurate.     

Potential of vibro-milling technique for preparation of electroceramic nanopowders

The potential of the vibro-milling technique as a simple method to obtain usable quantities of single-phase electroceramic powders with nanosized particles was examined. A detailed study considering the role of both milling time and firing condition on phase formation and particle size of the final product was performed. The calcination temperature for the formation of the desired phase was lower when longer milling times have been applied. More importantly, by employing an appropriate choice of the milling time and calcination condition, high purity electroceramic nanopowders have been successfully prepared with a simple solid-state reaction method.     

A light refractory concrete for thermal insulation

Compositions have been developed for nonshrinking vibrocast thermally insulating light refractory concretes with densities of 1.0, 1.3, 1.5, and 1.8 g/cm³ for temperatures of use up to 1400°C. The structure and properties have been examined for the concrete of density 1.3 g/cm³. __________ Translated from Novye Ogneupory, No. 4, pp. 29–32, April, 2008.