Microstructure of TiO2 and ZnO Films Fabricated by the Sol-Gel Method

Titanium dioxide and zinc oxide films were fabricated by spin-on and dip-coating methods. Both types of films exhibited columnar grains when the single coating was thin, ∼10 nm. The columnar TiO₂ films were dense, as confirmed by their density values calculated from the refractive index and TEM results. The addition of Al cations into the ZnO suppressed grain growth, because Zn had a lower diffusivity in the doped films. The doped ZnO films had nearly the same electrical resistivity as that of the undoped films.     

Polymerization of methyl methacrylate by tri-n-butylborane in the presence of amino acid esters

The polymerization of methyl methacrylate by tri-n-butylborane in the presence of amino acid esters was investigated. The binary systems of tri-n-butylborane and amino esters were found to be more effective for initiating the polymerization than tri-n-butylborane alone. Co-catalytic effects of amino acid esters were in the order: tyrosinate > glutamate > aspartate ? phenyl alaninate > serinate > glycinate. The rate of polymerization in a mixture of dimethylsulphoxide and toluene was proportional to the square root of the concentration of the initiator system, to the monomer concentration, and to the concentration of dimethylsulphoxide in the solvent. The overall energy of activation was estimated to be 4.6 kcal/mol for the tri-n-butylborane/methyl tyrosinate system. Copolymerization curves gave a typical free-radical character.     

Development of a high‐resolution RGBW flexible display using a white organic light‐emitting diode with microcavity structure and that of a side‐roll touch panel

In this study, white organic electroluminescent devices with microcavity structures were developed. A flexible high‐resolution active‐matrix organic light‐emitting diode display with low power consumption using red, green, blue, and white sub‐pixels formed by a color‐filter method was fabricated. In addition, a side‐roll touch display was developed in combination with a capacitive flexible touch screen.     

Melt viscosity and flow birefringence of polycarbonate

Melt viscosity and flow birefringence of bisphenol A-type polycarbonate were measured and analyzed by the application of rubber-like photoelastic theory. The melt viscosity in the Newtonian flow region increased with the molecular weight to the power of 3.4. In polycarbonate, the shear stress of the Newtonian flow region was to 10⁶ dyn/cm², whereas in PMMA it was at most 3 = 10⁵ dyn/cm². The flow birefringence δn has a linear relation with shear stress S, that is δn = 5.7 × 10^?10 S. The principal polarization difference of flow unit α₁ – α₂ was 1.62 × 10^?23 cm³, which was obtained by the application of the rubber-like elastic theory. In PMMA, it was 3.9 = 10^?25 cm³; about 1/40 of that was polycarbonate. The anisotropy of polarizability of the flow unit of polycarbonate was also about 40 times larger than that of PMMA. So the anisotropy reflected the large flow birefringence of the polycarbonate.     

Interfacial tension of demixed polymer solutions near the critical temperature: polystyrene + methylcyclohexane

Interfacial tension between demixed solutions of polystyrene + methylcyclohexane has been measured near the critical temperature as a function of temperature using polystyrenes with molecular weights 9000 ～ 1.26 × 10⁶. The critical exponent for the interfacial tension was determined to be about 1.30 for the lower molecular weight systems. However, for higher molecular weights the exponent could not be obtained because the system departed from critical behaviour. Magnitudes of the interfacial tension were proportional to about N^?0.44, where N is the polymerization index. Experimental results were compared with the recently-proposed theories and found to be in qualitative agreement. The tricritical theory of polymer solutions was also compared with the experimental results.     

A superconducting filter to separate an oxygen and argon mixture

Hot isostatic pressing in an oxygen atmosphere, known as O₂-HIP method, has been used successfully to synthesize oxide materials, as well as to produce porous materials. In this paper a porous superconducting oxide is synthesized by this method and its application as a gas filter is described. Porous superconductors can be used to separate a mixture of paramagnetic and diamagnetic gases, such as oxygen and argon. Separation occurs after a magnetic field is applied and is based on the Meissner effect. Experimental results showed that the oxygen content of an oxygen/argon mixture increased after passing through a filter with large pore size (about 10 m).     

Additional kernel observer: privilege escalation attack prevention mechanism focusing on system call privilege changes

International Journal of Information Security - Cyberattacks, especially attacks that exploit operating system vulnerabilities, have been increasing in recent years. In particular, if administrator...     

Microstructure development of steel during severe plastic deformation

The microstructure development during plastic deformation was reviewed for iron and steel which were subjected to cold rolling or mechanical milling (MM) treatment, and the change in strengthening mechanism caused by the severe plastic deformation (SPD) was also discussed in terms of ultra grain refinement behavior. The microstructure of cold-rolled iron is characterized by a typical dislocation cell structure, where the strength can be explained by dislocation strengthening. It was confirmed that the increase in dislocation density by cold working is limited at 10¹⁶m⁻², which means the maximum hardness obtained by dislocation strengthening is HV3.7 GPa. However, the iron is abnormally work-hardened over the maximum dislocation strengthening by SPD of MM because of the ultra grain refinement caused by the SPD. In addition, impurity of carbon plays an important role in such grain refinement: the carbon addition leads to the formation of nano-crystallized structure in iron.