Image synthesis in the electron microscope

A new method is described for transferring phase contrast in electron microscopy without artefacts due to oscillations of the phase contrast transfer function (PCTF). This is carried out by in situ image synthesis of two or three exposures transferred with complementary PCTF. The essence of the technique is to use optimized transfer attenuation functions to cut off the negative parts of PCTF.     

Special numbers,still proceedings,other novelties

Modifications of solid water and their transitions are described as they relate to cryo electron microscopy. In particular, the various amorphous states (amorphous polymorphs) as they exist below 100 K are extensively investigated. The “high-density” midification exhibits a lower viscosity than the “low-density” form. Differences are also observed in the mechanism of void formation due to electron irradiation: in the high-density form, voids are formed — not, however, in the low-density form. Together with the reaction to radiation damage, the physical properties of amorphous solid water are discussed with respect to embedding of organic specimens. Finally, the conditions and pitfalls associated with preparation of thin and entirely vitrified ice layers by shock-freezing are described.     

Tube-shaping unit — A way of improving the quality of shaped tubes

Lenin Dnepropetrovsk Pipe Plant. Translated from Metallurg, No. 8, p. 39, August, 1989.     

Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Occupational airway diseases in the metalworking industry Part 1: Respiratory infections, pneumonia, chronic bronchitis and emphysema

Occupational airway diseases are now receiving attention in industry, although study is hampered by a lack of readily-available data. The interpretation of the data that is available, and also of the root problems themselves, is itself a difficult problem. This paper has been written as a literature review which it is hoped that other researchers can take either as a starting point or as a refresher.     

“Metallisation” of oxide surfaces observed by in situ high-resolution electron microscopy

Intense irradiation (25–40 A/cm²) at intermediate energy (400 keV) has been found to cause “metallisation” of tungsten oxide and titanium niobate crystal surfaces. The possible mechanisms and the likely consequences for high-resolution imaging of clean oxide surfaces are briefly discussed.     

The contact of elastic regular wavy surfaces

A complete solution in closed form to the elastic contact of a one-dimensional sinusoidal surface with a flat surface was presented by Westergaard in 1939. This paper is concerned with the elastic contact of a two-dimensional sinusoidal surface with a flat. In this case the stress distribution within the elastic solids is three-dimensional. As the load is increased the contact areas change in shape from being circular to square and finally leave a circular region of no contact when the waves are almost squashed flat. The problem is solved in general using a numerical method due to Kalker, but asymptotic solutions in closed form have been found for light loads and also for heavy loads at which contact is almost complete. The variation of the mean separation with load, which determines the volume of the space trapped between the two surfaces, is also found.     

The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.