Optically tuned superconductive-dielectric resonators with whispering-gallery modes

An analytical method is presented for calculating the resonant frequency andQ-factor of a superconducting dielectric disk resonator operating in millimeter-wave regime with whispering-gallery mode. Resonant frequency shift due to the optical generation of quasi-particles in superconducting film is investigated as a function of photon flux. An optically tunable resonant frequency of about 500 MHz is estimated, and good agreement is found between numerical results and experimental ones.     

Determination of tablet coating distribution by deconvolution of uncoated and coated tablet weight distributions

PURPOSE: The purpose of this research is to obtain the tablet coating distribution from weight distributions of uncoated and coated tablets. METHODS: The method of deconvolution with digital smoothing was used to calculate the distribution of coating applied to a tablet population from separate random measurements of individual uncoated and coated tablets. RESULTS: It was demonstrated that the calculated coating weight distribution agrees well with the measured distribution. The effect of the smoothing factor on the solution is illustrated. CONCLUSIONS: This method can be used during development to facilitate process scale-up/optimization. In routine production, the method can assess the reproducibility and consistency of a coating process.     

Precipitation behavior of σ phase in fusion zone of dissimilar stainless steel welds during multi-pass GTAW process

The purpose of this study is to investigate the precipitation characteristics of σ phase in the fusion zone of stainless steel welds at various welding passes during a tungsten are welding (GTAW) process. The morphology, quantity, and chemical composition of the δ-ferrite and σ phase were analyzed using optical microscopy (OM), a ferritscope (FS), a X-ray diffractometer (XRD), scanning electron microscopy (SEM), an electron probe micro-analyzer (EPMA), and a wavelength dispersive spectrometer (WDS), respectively. Massive δ-ferrite was observed in the fusion zone of the first pass welds during welding of dissimilar stainless steels. The σ phase precipitated at the inner δ-ferrite particles and decreased δ-ferrite content during the third pass welding. The σ and δ phases can be stabilized by Si element, which promoted the phase transformation of σ→ϱ+λ₂ in the fusion zone of the third pass welds. It was found that the σ phase was a Fe−Cr−Si intermetallic compound found in the fusion zone of the third pass welds during multi-pass welding.     

Experimental Study on Energy Consumption of Combined Conventional and Dehumidification Drying

Conventional drying, dehumidification drying, and combined conventional-dehumidification drying of wood were experimentally studied in this article. The results showed that the energy consumption in the dehumidification drying is the least but its drying time is the longest. The energy consumption in the combined drying is more than that in the dehumidification drying but less than that in the conventional drying, and the drying time is half of that in the dehumidification drying. The advantages of the combined conventional and dehumidification drying are discussed from the experiments results.     

MEASUREMENT OF COEFFICIENTS FOB SIMULTANEOUS HEAT AND MASS TRANSFER IN FOOD PRODUCTS

Two experimental devices were designed and built to determine four coefficients K_T K_M D_M D (or δ_T = D_T / D_M occurring in simultaneous heat and mass transfer equations, where,K _T and D_M are thermal conductivity and moisture diffcusivity respectively, D_T ( or δ _T is temperature gradient Induced moisture migration coefficient and K_M is moisture gradient Induced heat transfer coefficient. Three food materials, i.e. potato, bread dough and bread, were tested. From this study, it was found that the value of 5 was higher for low density food materials, such as bread, than for high density materials, such as potato. The coefficient & measures moisture migration contribution due to temperature gradient within the material. The average values of δ _T for potato, bread dough and bread were 0.0014, 0.0059 and 0.0127 per °C, respectively. The contribution of temperature gradient to the overall moisture migration is negligible In high density materials. However, this contribution may be important in the moisture migratlon analysls for low density materials. The moisture gradient induced heat transfer coefficient % as found to be negligible for the materials tested in this study     

Prognostic factors of primary liver cancer

To investigate the prognostic factors of primary liver cancer (PLC) and improve the long-term results, 1,248 cases of PLC were analysed. Univariate analysis demonstrated that discovery approach, staging of PLC, original gamma-GPT, resection, radical resection, original AFP, tumor size, tumor number, and tumor capsule have very significant effects on prognosis of PLC (all P < 0.001); cirrhosis, HBsAg, local resection, and tumor embolus in portal vein were also significant difference (all P < 0.05); age, sex, original AFP, hepatitis, and differentiation of PLC cells were no significant difference (all P > 0.05). Multivariate analysis demonstrated that original gamma-GPT, radical resection, tumor size, and tumor number were the most significant prognostic factors (all P < 0.001). Some aspects improving long-term survival were discussed.     

Handling degenerate cases in exact geodesic computation on triangle meshes

The computation of exact geodesics on triangle meshes is a widely used operation in computer-aided design and computer graphics. Practical algorithms for computing such exact geodesics have been recently proposed by Surazhsky et al. [5]. By applying these geometric algorithms to real-world data, degenerate cases frequently appear. In this paper we classify and enumerate all the degenerate cases in a systematic way. Based on the classification, we present solutions to handle all the degenerate cases consistently and correctly. The common users may find the present techniques useful when they implement a robust code of computing exact geodesic paths on meshes.