Topology design and bridge-capacity assignment for interconnecting token ring LANs: A simulated annealing approach

We address the problem of determining the topology and bridge-capacity assignments for a network connecting a number of token rings via source-routing bridges. The objective is to minimize the cost of bridge installations while meeting the network users' performance requirements. The problem is modeled as a mixed 0–1 integer program. A comparison is given between two solution algorithms: a simulated annealing algorithm using the flow-deviation algorithm for each routing subproblem, and a drop algorithm using the simplex method for the same subproblems to provide benchmark solutions. In the former algorithm, the routing subproblem is formulated as a nonlinear program with penalty functions to model node and link capacity constraints, and in the latter as a multicommodity flow model with the same capacity constraints. Computational results show that the simulated-annealing/flow-deviation algorithm produced substantially better solutions than the LP-based drop algorithm.     

Reduction of loading effect by tungsten etchback in a magneticallyenhanced reactive ion etcher

The plug loading effect occurring during the etchback of tungsten was investigated in a magnetically enhanced reactive ion etcher using SF ₆/Ar mixtures. It was found that while the plug loading effect is independent of varying SF₆/Ar flow rate ratio and magnetic field intensity, it is reduced under the condition of high selectivity of tungsten relative to TiN which was achieved at high chamber pressure and low RF power. It is proposed that when TiN is used as a glue layer, the W etch rate enhancement in the plug is mainly controlled by a local loading effect. Under the optimized etchback conditions the plug loss was successfully controlled without the tungsten residue left on severe topology     

Apoptosis as a cause of death in measles virus-infected cells

To determine the mechanism of measles virus-induced cell death, we studied the infection of Vero cells and monocytic cell lines with wild-type (Chicago-1) and vaccine (Edmonston) strains of measles virus. DNA fragmentation indicative of apoptosis was apparent by flow cytometry, agarose gel electrophoresis, and electron microscopy. Within syncytia, DNA strand breaks were demonstrated by end labeling with terminal transferase and then by visualization.     

Mode analysis of DFB SE lasers

This paper presents theoretical results on mode characteristics of surface-emitting (SE) lasers utilizing an active second-order grating section. Based on a coupled-mode approach, longitudinal modes and the associated space-harmonic transverse modes are calculated via a numerical technique. From these, the lasing-mode spectrum, near- and far-field patterns of the radiation mode, and the surface-emission power efficiency are obtained. Effects of the substrate reflector and the grating parameters are also investigated. Finally, comparisons are made with conventional, edge-emitting DFB lasers. The results indicate that with a suitable choice of structural parameter values, DFB SE lasers can be made to possess both the spectral discrimination of the conventional DFB lasers and the advantages of SE lasers at the same time and also that the second lowest longitudinal mode may be preferred over the fundamental longitudinal mode for many applications due to its symmetric field distribution     

The oxidative inducation test applied to medical PVC and other polymers

We have examined the applicability of this simple and effective test to polymer systems widely used in the medical industry. First, it was found that not every polymer examined exhibited a distinct onset of autocatalytic oxidation detectable by DSC. However, for cases where distinct onsets are found, powerful insights can be obtained. These included activation energy of the degradation, thermal oxidative shelf life prediction, and correlation, with product performances. Actual examples are presented to illustrate the utility of the test.     

Einfluß der Korngröße auf mechanische Eigenschaften und den ungeschmierten reversierenden Gleitverschleiß von Al2O3-Keramik

Influence of grain size on mechanical properties and dry oscillating sliding wear of Al₂O₃-ceramics Specimens with average grain sizes varying between about 0.8 μm and 12 μm were produced by cold isostatic pressing of high purity Al₂O₃-powder followed by sintering between 1300°C and 1700°C. Hardness, Young's modulus, bending strength and fracture toughness were measured as a function of average grain sizes. Tribological tests were carried out on the different microstructures at normal laboratory air and room temperature by using a ring-on-block tribometer. Experimental results showed the dependence of mechanical properties on grain size, hardness and bending strength obeying a Hall-Petch type relation, approximately. Coefficient of friction was relatively independent of grain size under the test conditions used. However, wear intensity increased substantially if a critical grain size was surpassed. This was due to a change in mechanisms of material removal which was confirmed by scanning electron microscopical studies of the worn surfaces.     

Aerodynamic effect on natural frequency and flutter instability in rotating optical disks

 Experimental studies on the aerodynamic coupling effect on natural frequencies and flutter instability of rotating disks are investigated in this paper. The experiments performed using a vacuum chamber and optical disks give two main results. One is that the aerodynamic effect by surrounding air reduces the natural frequencies and critical speeds of the vibration modes in pre-flutter regions. The other is that the natural frequency of the disk rotating at ambient atmospheric pressure is equal to that in vacuum at the flutter onset speed where the disk experiences aero-induced flutter. In post-flutter regions, the aerodynamic coupling between the disk and surrounding air increases the natural frequencies of the disk. Received: 17 June 2002/Accepted: 7 October 2002 The work was supported by Grant No. R11-1997-042-090001-0 of the Center for Information Storage Devices designated by the Korea Science & Engineering Foundation. Paper presented at the 13th Annual Symposium on Information Storage and Processing Systems, Santa Clara, CA, USA, 17–18 June, 2002     

The design of experiments when there are errors in all the variables

The Error-in-Variables Model (EVM) applies to a large class of problems in parameter estimation in which there is error in all the variables. This property makes it of more general applicability than the widely used technique of ordinary Least Squares. While there is a voluminous literature on EVM there is nothing on a general method for designing experiments when EVM applies. In this paper we present an extension of the concept of D-optimality to provide such a general method. It is illustrated by applying it to the estimation of copolymer reactivity ratios and to fitting an ellipse.     

Optical measurements of thermal diffusivity of a material

The measurement of thermal diffusivity of a material (in particular, a thin film) is important for various reasons, e.g., to predict the heat transfer in the solid subjected to a thermal process, to monitor surface composition or morphology, or to detect invisible subsurface defects like delaminations. This measurement can be done in a noncontact manner using various photothermal methods. Such methods typically involve pulsed heating of the surface by small amounts using a laser source; the decay of the surface temperature after this pulsed photothermal heating is then probed to provide the thermal diffusivity. Various probing methods have been developed in the literature, including the probing of reflection, refraction, and diffraction from the pulsed heated area, infrared thermal radiometry, and surface deformation. This paper provides an overview of such techniques and some examples of their applications.