Effect of preparation technique on the properties of Mo-containing Al-MCM-41

The Al-MCM-41 has been used as support to prepare Mo-containing catalysts. The 12- molybdophosphoric heteropoly acid (HPMo) is used as initial compound. The catalysts are synthesized by two different methods: incipient impregnation with aqueous solution of the acid and mechanochemical synthesis. The samples were tested in the reaction of the thiophene hydrodesulfurization after activation with mixture H₂ + H₂S. The effect of the preparation method of the catalysts on their physicochemical and catalytic properties has been studied. A partial destruction of the loaded compound is observed in mechanochemically treated sample whereas the aggregates are formed from the particles of different size in the impregnated sample. The specific surface area of the sample prepared by mechanical–chemical treatment decreases 2–3 times, while the total pore volume is about four times lower. The HDS activity is higher on the impregnated sample than on the mechanochemically treated one.     

A small-angle X-ray scattering study of powder compaction

This work demonstrated a novel and potentially important application of two-dimensional small-angle X-ray scattering (2D-SAXS) to investigate powder compaction. SAXS from powder compacts of three materials commonly used for pharmaceutical tabletting exhibited azimuthal variations, with stronger intensity in the direction of the applied compaction force, relative to the transverse direction. This implied that compaction of a (macroscopic) powder could also produce changes on the molecular (nanometre) scale, which can be probed by 2D-SAXS. Two possible explanations for this effect were suggested. A combination of anisometric (i.e. elongated or flattened) granules with anisotropic morphologies could result in azimuthal variation in X-ray scattering due to granule orientation. It is expected that this mechanism would require relatively low packing density, so may operate during die filling. Granule re-orientation appeared less likely at higher packing densities and compaction pressures, however. Under these conditions, the changes in the 2D-SAXS patterns would be consistent with the powder granules becoming relatively flattened in the compression direction, with corresponding changes in their nano-scale morphology. The magnitude of this effect was found to vary between the materials used and increased with compaction pressure. This suggested that 2D-SAXS studies could provide useful information on force-transmission within a compressed powder. Further analysis of the data also suggested differences in the compaction mechanisms (i.e. granule re-orientation, deformation or fragmentation) between the materials studied.     

Formation and electronic structure of interface

In the present work the formation of the interface between polycrystalline silver and thin films of titanium oxide was studied with photoelectron spectroscopy (XPS, UPS) and time-of-flight secondary ion mass spectrometry (TOF-SIMS). Titanium oxide was deposited stepwise on 100 nm thick silver films by reactive magnetron sputtering allowing to study the evolution of the interface formation process. The process involves two steps: formation of thin layer of silver oxide and subsequent growth of the TiO₂ film. For better understanding of the silver oxidation process, pure silver films were exposed to a low temperature Ar/O plasma for different time intervals providing a possibility to investigate early stages of the oxide film growth.     

利用LIN节点的温度显示

串行多路传输总线如CAN或LIN可以解决车内因导线过多所带来的许多问题。低成本的LIN总线很适合应用于车门等这些对传输速率要求不高的场合,最高速率为20kbit/s的LIN总线完全可以满足要求。车外温度显示就是这样一个应用实例,外部温度传感器通常布置在后视镜中,数据产生于车门。但是实际显示位置是距此一定距离的车内,LIN总线可使布线简单,因为LIN节点只有3根导线:LIN数据线、电源线和地线。     

Revisiting the need for formal education in visualization.

Defining visualization education is still a work in progress. Visualization education is not just a subject within computer science. Computer scientists are not always the appropriate choice to teach visualization courses on their own. Visualization is not just mastering a set of concepts but acquiring skills. Student should learn by doing, either using one tool or a variety of tools, depending on the course's focus.     

Deflection Calculation of FRP Reinforced Concrete Beams Based on Modifications to the Existing Branson Equation

Fundamental concepts of tension stiffening are used to explain why Branson’s equation for the effective moment of inertia Ie does not predict deflection well for fiber reinforced polymer (FRP) reinforced concrete beams. The tension stiffening component in Branson’s equation is shown to depend on the ratio of gross-to-cracked moment of inertia (Ig/Icr), and gives too much tension stiffening for beams with an Ig/Icr ratio greater than 3. FRP beams typically have an Ig/Icr ratio greater than 5, leading to a much stiffer response and underprediction of computed deflections as observed by others in the past. One common approach to computing deflection of FRP reinforced concrete beams has been to use a modified form of the Branson equation. This paper presents a rational development of appropriate modification factors needed to reduce the tension stiffening component in Branson’s original expression to realistic levels. Computed deflections using this approach give reasonable results with the right modification factor, and compare well with a more general unified approach that incorporates a realistic tension stiffening model. Comparison is made with the existing and past correction factors recommended by ACI 440 for predicting deflection of FRP beams. The method presently used by ACI 440 gives reasonable estimates of deflection for glass and carbon FRP reinforced beams. However, this method underestimates deflection of aramid FRP reinforced beams and is restricted to rectangular sections. A proposal is made for adoption of a simple modification factor that works well for all types of FRP bar and beam cross-sectional shape.     

The role of experience in liking "read-to-drink" alcoholic beverages.

Ready-to-drinks (RTDs) are composed of an alcoholic component and a soft-drink base and are primarily consumed by a youth market. The authors explored whether liking and experience with an RTD soft-drink base predicts liking for the RTD. Participants (N=350) from ages 12 to 30 years sampled 3 RTDs and their respective soft-drink and alcoholic components. For milk- and fruit-based RTDs, liking for and familiarity with their soft-drink base was the best predictor of liking for and familiarity with the RTD itself. For the Coke-based RTD, familiarity with and liking for bourbon best predicted familiarity with and liking for the RTD. All of these effects were consistent across blind and nonblind testing. The authors' results suggest that where there is perceptual similarity between the RTD and its soft-drink base, these beverages may provide an easy transition into alcohol consumption for novice drinkers. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Applications of the discrete element method in mechanical engineering

Compared to other fields of engineering, in mechanical engineering, the Discrete Element Method (DEM) is not yet a well known method. Nevertheless, there is a variety of simulation problems where the method has obvious advantages due to its meshless nature. For problems where several free bodies can collide and break after having been largely deformed, the DEM is the method of choice. Neighborhood search and collision detection between bodies as well as the separation of large solids into smaller particles are naturally incorporated in the method. The main DEM algorithm consists of a relatively simple loop that basically contains the three substeps contact detection, force computation and integration. However, there exists a large variety of different algorithms to choose the substeps to compose the optimal method for a given problem. In this contribution, we describe the dynamics of particle systems together with appropriate numerical integration schemes and give an overview over different types of particle interactions that can be composed to adapt the method to fit to a given simulation problem. Surface triangulations are used to model complicated, non-convex bodies in contact with particle systems. The capabilities of the method are finally demonstrated by means of application examples. Commemorative Contribution.