An experimental behaviour of concrete-filled steel tubular columns

In this paper results of tests conducted on 27 concrete-filled steel tubular columns are reported. The test parameters were the column slenderness, the load eccentricity covering axially and eccentrically loaded columns with single or double curvature bending and the compressive strength of the concrete core. The test results demonstrate the influence of these parameters on the strength and behaviour of concrete-filled steel tubular columns. A comparison of experimental failure loads with the predicted failure loads in accordance with the method described in Eurocode 4 Part 1.1 showed good agreement for axially and eccentrically loaded columns with single curvature bending whereas for columns with double curvature bending the Eurocode loads were higher and on the unsafe side. More tests are needed for the case of double curvature bending.     

Stability analysis of simply-supported rectangular plates under non-uniform uniaxial compression using rigorous and approximate plane stress solutions

The non-classical problem of buckling of a simply-supported rectangular plate due to various types of non-uniform compressive edge loads is analysed here. For each case, the elasticity solution for the internal in-plane stress field is obtained rigorously using a superposition of Airy's stress functions and also approximately using extended Kantorovich method. Subsequently, the convergent buckling loads are obtained using Galerkin's method. Results are presented to highlight the dependence of the total buckling load and the corresponding buckled shape on the edge load distribution, as well as to illustrate the applicability of the approximate plane stress solutions.     

Field measurement of the air flow characteristics of big mechanically ventilated spaces

Air speeds induced by mechanical ventilation systems in the occupied zone are studied experimentally in seven railway stations in Hong Kong. Values of air speed at different positions are measured. From these values, air speed contours and turbulence intensities are calculated. Macroscopic numbers describing airflow in a space including the Reynolds number and the jet momentum number are estimated and their potential uses are discussed.     

Profiles of mean wind speeds and vertical turbulence intensities measured at seashore and two inland sites using Doppler sodars

The authors’ group has been conducting full-scale measurements of wind velocities with Doppler sodars. It is very important to accurately assess the profiles of mean wind speeds and turbulence intensities in relation to terrain roughness. In this study, the profiles were evaluated for all data measured over a long period at a seashore and two inland sites. It is confirmed that for strong winds the profiles can be approximated by a single power law at altitudes between 50 and 340 m. The power law exponents of the mean wind speed profiles are approximately 0.1 for wind from the sea and 0.2-0.3 for wind blown over land. Those of the turbulence intensity profiles are approximately 0 and −0.2 to 0.4, respectively.     

Betons a hautes performances,a granulats artificiels actifs

High strength concretes, in particular at early ages (more than 40 MPa at 3 days and up to 80 MPa at 7 days), are obtained by replacement of certain granular size ranges of sand or gravel by cement-active artificial aggregates in a given concrete composition elaborated with a local supply of aggregates and cement. The strengthening of the paste-aggregate bond by chemical reactions between the artificial aggregates and the cement also involves an improvement of other concrete performances and not only of mechanical strengths. The cracking ability is decreased, the wear strength is higher, and water permeability is low or even nil for certain compositions. The laboratory results are confirmed by tests on the site and show the possibility of achieving high strength concretes without any particular selection of cement and natural aggregates.     

Circular footings resting on geotextile-reinforced sand bed

The note pertains to an experimental study made on circular footings resting on semi-infinite layer of sand reinforced with geotextiles. Using the concept of homogenization of such soils, both analytical and numerical analyses have also been conducted to predict the load-settlement behavior and compared with experimental observations. The study highlights the effect of the footing size, number of reinforcing layers, reinforcement placement pattern and bond length and the relative density of the soil on the load-settlement characteristics of the footings.     

Effect of chlorination practice on soluble organics

As the practice of chlorination for the disinfection of waste effluents is apparently to be extended, this study was initiated to examine the possibility that chlorinated organics could be formed in the disinfection process. A group of pure compounds that had been demonstrated to be susceptible to chlorination were examined under conditions likely to apply under normal disinfection practice.From the results obtained, it appears only organics with ring structures and electron activating substituents, or amino groupings are capable of chlorination. The frequent presence of ammonia or amino groups means that chloramine formation with its asociated toxicity is likely. However, the presence of ammonia or amino groups will retard the reaction with other compounds making chlorination of these unlikely.     

新的钢化技术及检验方法

近期有几个因素影响到玻璃钢化领域,不仅钢化工艺本身是推动钢化工业的主要因素,其它因素比如钢化市场的参与者们正面临着日益上升的全球化的竞争;客户需要高质量的产品和安全装配规则,新发明的非破坏性检验方法正代替成本较高的老方法;市场上满足汽车及建筑工业要求的新产品;最后钢化设备制造商所生产的满足于新玻璃产品的热处理要求的新产品。对这些问题全面进行了讨论以便为今天的钢化技术提供一个完整的画面。同时也对使用新钢化技术使钢化工业有更辉煌的明天提出了一些建议。     

Determination of flexibility of beam-to-column connectors used in thin walled cold-formed steel pallet racking systems

This paper describes a new test to determine flexibility of beam-to-column connectors used in conventional pallet racking systems. In this study, two different ways were used to find the flexibility of a connector. The connector developed was tested using the conventional cantilever method [Bajoria, KM. Three dimensional progressive collapse of warehouse racking, PhD Thesis, University of Cambridge, UK 1986], and then also using a newly proposed double cantilever method. To verify the results obtained from both the tests, a full scale frame test was carried out. In the double cantilever test the connector is subjected to three types of forces namely moment, shear and the axial pull by the beams, thereby giving behavior close to practical usage of connectors. Non-linear finite element analysis of both the tests and also of the full scale test were carried out using ANSYS [ANSYS 7.0—User's Manual, ANSYS Inc., 2005] software. The results obtained from the double cantilever test were found to match well with the full scale frame test. The experimental results and the finite element results are compared in this paper.