Effect of Alumina Reactivity on the Densification and Properties of Al2O3–Cr2O3 Refractories

Alumina‐chrome (Al₂O₃–Cr₂O₃) refractories with Al₂O₃:Cr₂O₃ molar ratio 1:1 were synthesized in the temperature range of 1400–1700°C by conventional solid–oxide reaction route. The effect of different aluminas (viz., hydrated and calcined) on the densification, microstructure, and properties of Al₂O₃–Cr₂O₃ refractories was investigated without changing the Cr₂O₃ source. The starting materials were analyzed to determine the chemical composition, mineralogy, density, surface area, and particle size. Sintered materials were characterized in terms of densification, phase assemblage, and mechanical strength at room temperature and at higher temperatures. Microstructural evolution at different sintering temperature was correlated with sintering characteristics. It can be concluded that the Al₂O₃–Cr₂O₃ refractories prepared with hydrated alumina as Al₂O₃ source show better densification and hot mechanical strength than corresponding calcined variety.     

Dual material gate junctionless tunnel field effect transistor

This paper proposes a junctionless tunnel field effect transistor (JLTFET) with dual material gate (DMG) structure and the performance was studied on the basis of energy band profile modulation. The two-dimensional simulation was carried out to show the effect of conduction band minima on the abruptness of transition between the ON and OFF states, which results in low subthreshold slope (SS). Appropriate selection of work function for source and drain side gate metal of a double metal gate JLTFET can also significantly reduce the subthreshold slope (SS), OFF state leakage and hence gives improved I _ON/I _OFF.     

Hot Ductility and Deformation Behavior of C-Mn/Nb-Microalloyed Steel Related to Cracking During Continuous Casting

Hot ductility studies have been performed on C-Mn and C-Mn-Nb steels with an approach to simulate the effect of cooling conditions experienced by steel in secondary cooling zone during continuous casting. Thermal oscillations prior to tensile straining deteriorate hot ductility of steel by deepening and widening the hot ductility trough. C-Mn steels are found to exhibit ductility troughs in three distinct zones whereas C-Mn-Nb steel shows drop in ductility only at low temperature in the vicinity of ferrite transformation temperatures. Start of ferrite transformation in steels causes yield ratio to increase while work hardening rates and strength coefficient decrease with decrease in test temperature in presence of thermal oscillation prior to tensile testing. Inhibition of recrystallization due to build-up of AlN particles along with the presence of MnS particles in structure and low work hardening rates causes embrittlement of steel in austenitic range. Alloying elements enhancing work hardening rates in austenitic range can be promoted to improve hot ductility. The presence of low melting phase saturated with impurities along the austenitic grain boundaries causes intergranular fracture at high temperature in C-Mn steels.     

Intradomain QoS routing in IP networks: a feasibility andcost/benefit analysis

Constraint-based routing gradually becomes an essential enabling mechanism for a variety of emerging network services such as virtual private networking and QoS support. A number of previous works have recognized its significance and investigated many aspects of the operation of constraint-based routing and in particular its variant concerned with determining paths for requests with specific QoS requirements, known as QoS routing. In this work we build on previous results on the cost of QoS routing and investigate the performance/cost trade-offs involved in the operation of a representative QoS routing architecture, elaborate on the constituents of this cost, and identify the main methods for containing the cost that QoS routing incurs on routers. Our results show that the cost of QoS routing is not excessive and that there indeed exist operational configurations, which can achieve reasonable performance gains with only a minimal increase in processing cost when compared to conventional best-effort routing     

Study of uranium sorption using D2EHPA‐impregnated polymeric beads

The extractant‐impregnated polymeric beads (EIPBs), containing Di(2‐ethylhexyl) phosphonic acid (D2EHPA) as an extractant and polyethersulfone as base polymer, were prepared by phase‐inversion method. These beads were characterized by fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and scanning electron microscope (SEM) analysis to gain insight into the composition and morphology of beads. The beads exhibited good acid stability as no significant structural deformation or leaching out of the extractant was observed in 6M HNO₃ solution, up to the studied equilibration time of 15 days. The synthesized EIPBs were evaluated, for their ability to absorb uranium from aqueous solution, at different concentration and pH values. The kinetics measurement showed that about 90 min of equilibration time was enough to remove saturation amount of uranium from the solution. Kinetic modeling analysis of the extraction results was carried out using pseudo‐first‐order, pseudo‐second‐order, and intraparticle diffusion equations and the corresponding rate constants were determined. The equilibrium data were fitted into different isotherm models and were found to be represented well by the Freundlich isotherm equation. Reusability of the beads was also established by multiple sorption–desorption experiments. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3355–3364, 2013     

Spectroscopic Studies of Model Photo-Receptors: Validation of a Nanosecond Time-Resolved Micro-Spectrophotometer Design Using Photoactive Yellow Protein and α-Phycoerythrocyanin

Time-resolved spectroscopic experiments have been performed with protein in solution and in crystalline form using a newly designed microspectrophotometer. The time-resolution of these experiments can be as good as two nanoseconds (ns), which is the minimal response time of the image intensifier used. With the current setup, the effective time-resolution is about seven ns, determined mainly by the pulse duration of the nanosecond laser. The amount of protein required is small, on the order of 100 nanograms. Bleaching, which is an undesirable effect common to photoreceptor proteins, is minimized by using a millisecond shutter to avoid extensive exposure to the probing light. We investigate two model photoreceptors, photoactive yellow protein (PYP), and α-phycoerythrocyanin (α-PEC), on different time scales and at different temperatures. Relaxation times obtained from kinetic time-series of difference absorption spectra collected from PYP are consistent with previous results. The comparison with these results validates the capability of this spectrophotometer to deliver high quality time-resolved absorption spectra.     

Systematic generation of OTA-C sinusoidal oscillators

The authors outline a method for generating all possible, canonic, linearly tunable, OTA-C sinusoidal oscillators systematically.<>     

Surface modification of semiconductor photoelectrode for improved solar cell performance

The investigation is focused on the synthesis of nanostructured TiO₂–CuO admixed photoelectrode and its use as a photoelectrode of high-efficiency PEC solar cells for hydrogen production. TiO₂, in the nanostructured form, has been prepared by hydrolysis of titanium(IV) isopropoxide solution. An improvement in the nanostructured TiO₂ photoelectrode carried out in the present work corresponds to admixing CuO to improve the spectral response. In the present study, photo-electrochemical (PEC) and hydrogen evolution characteristics of new types of ns-TiO₂–CuO admixed/Ti septum-based semiconductor septum photo-electrochemical (SC-SEP PEC) solar cell has been studied. The CuO admixed ns-TiO₂ exhibited a high photocurrent and photovoltage of 18.6 mA/cm² and 680 mV, respectively. The ns-TiO₂–CuO electrode exhibited a higher hydrogen gas evolution rate of 14.00 l/h m².