冷却器盘管失效分析及防范措施

本文介绍了冷却器盘管破裂泄漏的情况，分析了失效破坏的原因，并提出防止冷却器盘管破裂泄漏的措施。     

四种杀菌剂对枸杞黑果病的防治效果

枸杞黑果病是枸杞产区的主要病害．发病后造成黑花、黑蕾和黑果，使枸杞产量降低，品质变劣。为探明四种杀菌剂对枸杞黑果病的防治效果及最佳剂量，2003年对下述四种杀菌剂进行了田间药效对比试验，调查防效结果如下：20％三苯基醋酸锡WP450～281g／hm^2(以有效成分计，下同)，20％氟硅唑EC21．08g／hm^21．5％噻霉酮EW16、88～21．08g／hm^2、40％氟硅唑EC450g／hm^2和70％甲基托布津WP787．5g/hm^2对枸杞黑果病防效均在88．25％以上。经LSD检验各处理间防效无显著差异。     

Electrochemical performance of nanocrystalline Li3V2(PO4)3/carbon composite material synthesized by a novel sol–gel method

A novel sol–gel method based on V₂O₅·nH₂O hydro-gel was developed to synthesize nanocrystalline Li₃V₂(PO₄)₃/carbon composite material. In this route, V₂O₅·nH₂O hydro-gel, NH₄H₂PO₄, Li₂CO₃ and high-surface-area carbon were used as starting materials to prepare precursor, and the Li₃V₂(PO₄)₃/carbon was obtained by sintering precursor at 750 °C for 4 h in flowing argon. The sol–gel synthesis ensures homogeneity of the precursors and improved reactivity. The sample was characterized by XRD, SEM and TEM. X-ray diffraction results show Li₃V₂(PO₄)₃ sample is monoclinic structure with the space group of P2₁/n. The TEM image indicates that the Li₃V₂(PO₄)₃ particles modified by conductive carbon are about 70 nm in diameter. The Li₃V₂(PO₄)₃/carbon system showed that the discharge capacities in the first and 50th cycle are about 155.3 and 143.6 mAh/g, respectively, in the range of 3.0–4.8 V. The sol–gel method is fit for the preparation of Li₃V₂(PO₄)₃/carbon composite material which may offer some favorable properties for commercial application.     

Phase Assemblages of Pr α-sialon Derived from SHS-ed Powders and TEM Study on the Nucleation of Pr α-sialon

The Pr α-sialon powders prepared by self-propagating high-temperature synthesis (SHS), consisting of 55 wt% Pr α-sialon and 45 wt% of β-sialon (abbreviated as α' and β'), were hot-pressed at 1800°C for 1 h. The results showed that Pr α' phase would transfer to β' with the appearance of JEM phase (Pr(Si_{6− z} Al _z )(N_{10− z} O _z )) after sintering, thus resulting in the increase of β' phase to 86 wt%. The addition of Y₂O₃ into SHS-ed Pr α' powders as the starting materials restrains the transformation of α' to β' and prevents the formation of JEM phase as well. The nucleation mechanism of Pr α' grain during hot-pressing was investigated in terms of transmission electron microscope and energy-dispersive spectrometer analysis. Two nucleation modes of Pr α' grains were found, i.e., nucleating on the undissolved Pr α' grains and on the nuclei of (Pr, Y) α' grains precipitated from liquid phase.     

Synthesis and characterization of copolythiophene

Copolythiophenes (Co‐PTs), poly(3‐hexylthiophene‐co‐3‐thiophene carboxylic acid) (P3HT‐TCa), poly(3‐hexyloxylthiophene‐co‐3‐thiophene carboxylic acid) (P3HOT‐TCa), and poly(3‐phenylthiophene‐co‐3‐thiophene carboxylic acid) (P3PhT‐TCa), were synthesized by chemical oxidized polymerization to investigate the effect of copolymerization on the properties of polythiophenes (PTs). Gel permeation chromatography showed that the molecular weight (MW) of Co‐PT was lower than that of homopolythiophene. Fourier transform infrared (FTIR) spectra indicated that the copolymerization was successful between the monomers. The λ_max of Co‐PTs gave a “blue shift” in ultraviolet‐visible (UV‐VIS) spectra. Photoluminescence (PL) spectra showed that the PL intensity of Co‐PT became weaker than that of homopolythiophene and the disappearance of PL had been observed in P3HOT‐TCa. The thermal stability of Co‐PT was influenced by the carboxyl for its low decomposition temperature. Furthermore, the copolymerization between multi‐wall carbon nanotube containing thiophene ring (MWNT‐Th) and 3‐hexyloxylthiphene could also take place successfully. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Integrated size and topology optimization of skeletal structures with exact frequency constraints

The present paper studies the integrated size and topology optimization of skeletal structures under natural frequency constraints. It is found that, unlike the conventional compliance-oriented topology optimization problems, the considered problem may be strongly singular in the sense that the corresponding feasible domain may be disconnected and the global optimal solutions are often located at the tips of some separated low dimensional sub-domains when the cross-sectional areas of the structural components are used as design variables. As in the case of stress-constrained topology optimization, this unpleasant behavior may prevent the gradient-based numerical optimization algorithms from finding the true optimal topologies. To overcome the difficulties posed by the strongly singular optima, some particular forms of area/moment of inertia-density interpolation schemes, which can restore the connectedness of the feasible domain, are proposed. Based on the proposed optimization model, the probability of finding the strongly singular optimum with gradient-based algorithms can be increased. Numerical examples demonstrate the effectiveness of the proposed approach.     

橡胶对HIPS树脂落锤指标的影响

通过对高抗冲聚苯乙烯树脂出现产品落锤指标偏低问题的分析，从橡胶配量及其粒径大小上进行了改进，同时改进了工艺操作，采取了提高反应釜搅拌速度、降低乙苯浓度等措施。结果产品合格率达到９９％以上，优级品率达到９８％以上。     

Effects of the reinforcement and toughening of acrylate resin/CaCO3 nanoparticles on rigid poly(vinyl chloride)

Novel composite particles based on nanoscale calcium carbonate (nano‐CaCO₃) as the core and polyacrylates as the shell were first synthesized by in situ encapsulating emulsion polymerization in the presence of the fresh slush pulp of calcium carbonate (CaCO₃) nanoparticles. Subsequently, these modified nanoparticles were compounded with rigid poly(vinyl chloride) (RPVC) to prepare RPVC/CaCO₃ nanocomposites. At the same time, the effects of the reinforcement and toughening of these modified nanoparticles on RPVC were investigated, and the synergistic effect of modified nanoparticles with chlorinated polyethylene (CPE) was also studied. The results showed that in the presence of nano‐CaCO₃ particles, the in situ emulsion polymerization of acrylates was carried out smoothly, and polyacrylates successfully encapsulated on the surface of nano‐CaCO₃ to prepare the modified nanoparticles, breaking down nano‐CaCO₃ particle agglomerates, improving their dispersion in the matrix, and also increasing the particle–matrix interfacial adhesion. Thus, the effects of the reinforcement and toughening of these modified nanoparticles on RPVC were very significant, and the cooperative effect of the nanoparticles with CPE occurred in the united modification system. Scanning electron microscopy analyses indicated that large‐fiber drawing and network morphologies coexisted in the system of joint modification of nanoparticles with CPE. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3940–3949, 2007     

十二烷基苯磺酸钠水溶液聚集性质的研究

用滴体积法测出十二烷基苯磺酸钠（ＳＤＢＳ）稀水溶液的表面张力；然后求出其临界胶束浓度（ＣＭＣ）。同时通过溶液的电导率、吸收光谱以及荧光光谱测定求出其ＣＭＣ。这样测出的ＣＭＣ值为１．２～１．６×１０－３ｍｏｌ／Ｌ，与文献值相符。也研究了部分水解的聚丙烯酰胺（ＰＨＰＡＭ）对ＳＤＢＳ聚集性质的影响；发现ＳＤＢＳ的ＣＭＣ值随ＰＨＰＡＭ的加人而减少并且ＰＨＰＡＭ水溶液的粘度随ＳＤＢＳ的存在而急剧降低（类似盐效应）。这些方法与性质对强化采油（ＥＯＲ）是重要的。     

Interbay物料自动搬运系统性能分析

Interbay物料自动搬运系统的运行效率对于晶圆制造系统影响较大,研究Interbay物料自动搬运系统的绩效具有较大的意义[1]。该文以带有捷径的单闭环背脊式布局的物料自动搬运系统为研究对象,通过问题描述,简化、假设将实际问题抽象为导引运输模型。然后,建立数学模型,采用Dijkstra算法确定工件搬运的最短路径。最后,利用Arena仿真软件建立含有导引运输设备的模型,采用控制变量法探究小车数量小车占用轨道的方式、调度规则等因素对于产出的影响,发现对于本文中的模型,其它条件相同时,搬运系统采用Release-at-end的控制方式,系统最大搬运量越大。