New anion exchanger organic–inorganic hybrid materials and membranes from a copolymerof glycidylmethacrylate and γ‐methacryloxypropyl trimethoxy silane

Organic–inorganic hybrid materials and mem branes were prepared through coating on Teflon plate or dip‐coating on microporous alumina substrates with the solution of glycidylmethacrylate (GMA) and γ‐methacryloxypropyl trimethoxy silane (γ‐MPS) copolymer, followed by ring‐opening of the GMA moiety with trimethylamine hydrochloric and sol–gel reaction of the γ‐MPS moiety. Composition of the GMA and γ‐MPS copolymer was varied by changing the feed ratio of GMA to γ‐MPS during the copolymerization. So the thermal stability, hydrophilicity, electrical properties, etc. of the hybrid materials and membranes were varied. Results showed that as the γ‐MPS amount increased in the copolymer, T_d (the temperature on thermogram at 5% weight loss) value of the hybrid materials and water contact angle of the hybrid membrane generally increased, while the anion exchange capacity, water uptake (W_R) and pure water flux decreased. The charge transition point of the hybrid membranes deduced from their streaming potential behavior decreased from pH > 12 to pH = 7–8 as the γ‐MPS amount increased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3580–3589, 2006     

4′-甲基2腈基联苯的合成

以邻氨基苯甲酸为起始原料,经重氮化、芳基化、取代和脱水等步骤合成药物中间体4′-甲基-2-腈基联苯.通过正交实验得到芳基化反应较佳条件为:10mol/L氢氧化钠15mL,甲苯30mL,反应温度5℃,反应时间5h,产物4′-甲基-2-联苯羧酸的产率为59.4%. 考察了脱水剂种类,脱水反应较佳的实验条件为氯化亚砜15mL,4′-甲基-2-联苯酰胺2.6g,反应8h,产物4′-甲基-2-腈基联苯的产率为67.7%.     

Exothermic effect in the process of electron‐beam curing of epoxy resins

Temperature measurements have been performed in the process of electron‐beam curing of EB‐I and EB‐II epoxy resin systems. The influence of initiator content, resin type, and dose rate on the temperature of the systems was studied. Transverse and longitudinal temperatures of samples in the glass vessel were also analyzed. The nature of temperature curves varied with the different epoxy resin systems in the steel mold, but did not change with different contents of the initiator. At the same time, the heat had no effect on the gel fraction of epoxy resin systems. The temperature curve was greatly affected by the dose rate, and its peak value, peak width, and plateau value also increased with it. The transverse temperature of EB‐II glass vessel samples increased as the radiation dose increased and, in the same sample, the temperature reduced as the distance between the radiation center and the test point increased. The longitudinal temperature of EB‐I and EB‐II resin systems in a glass vessel decreased as the radiation depth increased. As the radiation dose increased, the temperature of the EB‐I resin system increased simultaneously, while that of the EB‐II resin system initially increased and then kept constant when the dose reached a certain value. The temperatures of these two resin systems decreased rapidly when the radiation process stopped. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2217–2222, 2004     

Creep and Stress Rupture Behavior of an Advanced Silicon Nitride: Part I, Experimental Observations

Cylindrical buttuohead specimens of an advanced silicon nitride were tested in uniaxial tension at temperatures between 1422 and 1673 K. In the range 1477 to 1673 K, creep deformation was reliably measured using high-temperature contact probe extensometry. Extensive scanning and transmission electron microscopy has revealed the formation of lenticular cavities at two-grain junctions at all temperatures (1422–1673 K) and extensive triple-junction cavitation occurring at the higher temperatures (1644–1673 K). Cavitation is believed to be part of the net creep process. The stress rupture data show stratification of the Monkman–Grant lines with respect to temperature. Failure strain increased with increase in rupture time or temperature, or decrease in stress. Fractography showed that final failure occurred by subcritical crack growth in all specimens.     

Dynamic viscoelasticity of low‐density polyethylene/in‐situ‐grafted carbon black composite

The study on the dynamic viscoelastic properties of grafted carbon black (g‐CB) filled low‐density polyethylene (LDPE) was carried out. Because of formation of CB networking, the characteristic modulus plateau and loss tangent arc appears. Addition of grafting monomer like butyl acrylate (BA) and acroleic acid (AA) enhances the interaction between particles and matrix due to accelerated formation of micronetworking in the composites induced by forming branch chains of AA and BA with multiunit. The decrease of the temperature corresponding to α_c mechanical relaxation together with AA (BA) addition given by the position of loss tangent (tan δ) peak for LDPE is owed to the formation of long‐chain polymer grafted between CB and the matrix, which facilitates the slip of the lamella of LDPE. The influence of maleic anhydride (MA) on enhancing interaction between LDPE and CB is not so pronounced, as compared with AA and BA because of no formation of long chain between CB particle and polymer matrix. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4127–4132, 2006     

旋风分离器内颗粒运动规律的数值模拟

采用单颗粒动力学模型计算了旋风分离器内颗粒的运动轨迹。计算结果表明：进入旋风分离器的颗粒绝大多数在环形空间内就被甩向器壁；从入口上部进入的部分较小颗粒由于局部二次流作用而上升形成顶灰环；还有少量颗粒进入下部分离空间。在下部分离空间内，有灰斗返气夹带上来的颗粒，处于内旋流的颗粒则有可能随上升气流而逃逸，所以一定的分离空间高度有利用颗粒的二次再分离。     

无底柱分段崩落法采矿进路受力过程分析

在使用无底柱分段崩落法的矿山,大都存在着地压现象。其主要表现是采矿进路和联络道的变形破坏。对采矿进路在开挖和回采过程中各阶段受力情况的分析表明,进路的变形、破坏主要是受到岩体初始静应力、爆破动应力和矿柱支撑应力的综合作用的结果。     

螺带式搅拌器在假塑液中的混合及放大的研究

本文综合研究了螺带式搅拌器在假塑性液体中的混合特性及动力特性，测定了双螺带，内外螺带及螺带螺旋３种类型搅拌器的功率常数Ｋｐ和Ｍｅｔａｎｅｒ常数Ｋｓ，并得出混匀操作和传质工艺过程的放大准则。     

Demineralization of a UK bituminous coal using HF and ferric ions

A UK bituminous coal has been used to study demineralization by two-stage chemical leaching. The first-stage uses hydrofluoric acid (HF) at 65 °C and reduces the ash content from 5.30 wt% to 1.37 wt% by mainly removing Al and Si containing minerals. Subsequent leaching by ferric ions decreases the ash content further to 990 ppm by removing most of the pyrite and fluorides formed during the HF leaching. Calorific value of the coal shows no change following leaching, which suggests no oxidation is occurring to the coal carbonaceous matrix. The mercury and sulfur contents after the two-stage leaching sequence decrease by 40% and 26%, respectively.